Unlike my previous several projects, I am doing at least some of the
assembly on the cookbook shelves before finishing. Worse yet, I will
probably be using stain.
I tried to remove all of the squeeze-out during the glue-up, but I was
working quickly and I am sure I got a gluey fingertip on the work at
least once or twice. I'm sure because I found such a spot today.
Even though I presanded everything, I decided to lightly resand the
outside faces at least. But how much is enough, and how do I check?
I just wiped some mineral spirits over one of the assemblies. I figure
any glue spots wouldn't "change color" due to being wet. Does that sound
right?
---
This email is free from viruses and malware because avast! Antivirus protection is active.
http://www.avast.com
On 10/26/2014 5:07 AM, John Paquay wrote:
> On 8/16/2014 1:56 PM, Greg Guarino wrote:
>> Unlike my previous several projects, I am doing at least some of the
>> assembly on the cookbook shelves before finishing. Worse yet, I will
>> probably be using stain.
>>
>> I tried to remove all of the squeeze-out during the glue-up, but I was
>> working quickly and I am sure I got a gluey fingertip on the work at
>> least once or twice. I'm sure because I found such a spot today.
>
> This was your first mistake.
> Never attempt to remove glue squeezeout during assembly. It will only
> make things worse. To deal with glue squeezeout:
> Complete your assembly.
> Take care not to disturb any glue squeezeout. Let it rise and leave it
> alone.
> Wait until the adhesive has begun to cure (with aliphatic resins, this
> is usually about 15-20 minutes). You can wait longer, but there is most
> definitely a 'sweet spot' in the timing for every adhesive.
> With a sharp chisel, shave the glue line. Adhesive that has squeezed out
> in beads will pop off the surface very easily and cleanly. Glue that has
> formed a continuous line of squeezeout may require waiting a little
> longer, but when the timing is right, it will peel off the wood and
> leave no residue.
> Let the glue finish hardening. You can then lightly shave or scrape the
> joint to make sure you've removed it all.
>
> This works because the squeezeout is just sitting on the wood, and has
> not penetrated into the wood's fibers, so its bond to the wood is
> extremely weak. Trying to wipe it or wash it off while it's wet or
> sticky simply pushes it into the fibers, making clean removal extremely
> difficult. I don't know how that wiping/washing method ever got pushed
> by so-called experts, but it's an exercise in futility.
>
>> Even though I presanded everything, I decided to lightly resand the
>> outside faces at least. But how much is enough, and how do I check?
>>
>> I just wiped some mineral spirits over one of the assemblies. I figure
>> any glue spots wouldn't "change color" due to being wet. Does that sound
>> right?
>
> Yes. Any liquid will darken the wood as it absorbs the liquid, and glue
> residue will remain a lighter color since it absorbs the liquid much
> less. That's why errant glue is a problem in the first place.
John, good to see you back here!
Been a long time, amigo.
--
eWoodShop: www.eWoodShop.com
Wood Shop: www.e-WoodShop.net
https://www.google.com/+eWoodShop
https://plus.google.com/+KarlCaillouet/posts
http://www.custommade.com/by/ewoodshop/
KarlCaillouet@ (the obvious)
On Saturday, August 16, 2014 12:56:49 PM UTC-5, Greg Guarino wrote:
> and I am sure I got a gluey fingertip on the work at least once or twice.
Don't worry about any fingerprints. It's a cookbook shelf. Chalk it up as cookbook shelf decor. Prolly, thems womens folk (and applicable mens folk) will have their cookingbooking fingerprints all over it, in no time.
Those cooking clean-freaks will think it's their messy prints and will huff and puff to scrub them off, so you're good to go, with a clear conscience.
Sonny
On 8/16/2014 1:56 PM, Greg Guarino wrote:
> Unlike my previous several projects, I am doing at least some of the
> assembly on the cookbook shelves before finishing. Worse yet, I will
> probably be using stain.
>
> I tried to remove all of the squeeze-out during the glue-up, but I was
> working quickly and I am sure I got a gluey fingertip on the work at
> least once or twice. I'm sure because I found such a spot today.
This was your first mistake.
Never attempt to remove glue squeezeout during assembly. It will only
make things worse. To deal with glue squeezeout:
Complete your assembly.
Take care not to disturb any glue squeezeout. Let it rise and leave it
alone.
Wait until the adhesive has begun to cure (with aliphatic resins, this
is usually about 15-20 minutes). You can wait longer, but there is most
definitely a 'sweet spot' in the timing for every adhesive.
With a sharp chisel, shave the glue line. Adhesive that has squeezed out
in beads will pop off the surface very easily and cleanly. Glue that has
formed a continuous line of squeezeout may require waiting a little
longer, but when the timing is right, it will peel off the wood and
leave no residue.
Let the glue finish hardening. You can then lightly shave or scrape the
joint to make sure you've removed it all.
This works because the squeezeout is just sitting on the wood, and has
not penetrated into the wood's fibers, so its bond to the wood is
extremely weak. Trying to wipe it or wash it off while it's wet or
sticky simply pushes it into the fibers, making clean removal extremely
difficult. I don't know how that wiping/washing method ever got pushed
by so-called experts, but it's an exercise in futility.
> Even though I presanded everything, I decided to lightly resand the
> outside faces at least. But how much is enough, and how do I check?
>
> I just wiped some mineral spirits over one of the assemblies. I figure
> any glue spots wouldn't "change color" due to being wet. Does that sound
> right?
Yes. Any liquid will darken the wood as it absorbs the liquid, and glue
residue will remain a lighter color since it absorbs the liquid much
less. That's why errant glue is a problem in the first place.
JP
--
This is my signature. Really. I'm not kidding. Stop reading now.
"Greg Guarino" <[email protected]> wrote in message
news:[email protected]
> Unlike my previous several projects, I am doing at least some of the
> assembly on the cookbook shelves before finishing. Worse yet, I will
> probably be using stain.
>
> I tried to remove all of the squeeze-out during the glue-up, but I was
> working quickly and I am sure I got a gluey fingertip on the work at
> least once or twice. I'm sure because I found such a spot today.
>
> Even though I presanded everything, I decided to lightly resand the
> outside faces at least. But how much is enough, and how do I check?
>
> I just wiped some mineral spirits over one of the assemblies. I figure
> any glue spots wouldn't "change color" due to being wet. Does that sound
> right?
Yes.
--
dadiOH
____________________________
Winters getting colder? Tired of the rat race?
Taxes out of hand? Maybe just ready for a change?
Check it out... http://www.floridaloghouse.net