I'll soon be working on building new kitchen cabinets. It will involve 24 or
so frame and raised panel doors. That's about 100 mortise and tenon joints.
Does anyone have anything good to say about the Delta mortising attachment
for a drill press, or would a dedicated benchtop mortising tool be a better
route to go? Either tool would be something that would see future use,
although I don't anticipate that volume of doors at any one time again. I
currently use a forstner bit, for mortises, looking for something quicker.
thanks.
Dan Williams wrote:
> I'll soon be working on building new kitchen cabinets. It will involve 24 or
> so frame and raised panel doors. That's about 100 mortise and tenon joints.
> Does anyone have anything good to say about the Delta mortising attachment
> for a drill press, or would a dedicated benchtop mortising tool be a better
> route to go? Either tool would be something that would see future use,
> although I don't anticipate that volume of doors at any one time again. I
> currently use a forstner bit, for mortises, looking for something quicker.
> thanks.
Consider using pocket screws instead of mortise and tenons. Much
faster and easier. Otherwise, IMHO a dedicated mortising machine is
better than the drill press attachment .
Dan Williams wrote:
> I'll soon be working on building new kitchen cabinets. It will involve 24 or
> so frame and raised panel doors. That's about 100 mortise and tenon joints.
> Does anyone have anything good to say about the Delta mortising attachment
> for a drill press, or would a dedicated benchtop mortising tool be a better
> route to go? Either tool would be something that would see future use,
> although I don't anticipate that volume of doors at any one time again. I
> currently use a forstner bit, for mortises, looking for something quicker.
> thanks.
I have a Delta mortising attachment. It's a fair amount of trouble to
mount it and set it up, but that shouldn't be a big issue for you since
you have so many to do. But it requires so much downforce that I was
afraid I'd bend the handle on my drill press. And it keeps the drill
press tied up so you can't use it for anything else. Like others said,
I'd use rail & stile bit for doors, but if you insist on mortises,
especially that many, go for the dedicated mortise machine.
DonkeyHody
"Even an old blind hog finds an acorn every now and then."
I know this is contrary to your question, but in Rochester NY we have a
Habitat for Humanity 'building supply' store, where home
builders/remodelers can donate leftovers.
On my most recent trip I saw several 'entire kitchen's worth' of doors
in excellent shape (maple, cherry) stained and finished- and they were
selling the doors for about 5 to 7$ a piece. Some even had the closure
hardware still attached.
And if I didn't have the wife with me I probably would have bought it
for just the wood....
Good luck!
Jason
Dan Williams wrote:
> I'll soon be working on building new kitchen cabinets. It will involve 24 or
> so frame and raised panel doors. That's about 100 mortise and tenon joints.
> Does anyone have anything good to say about the Delta mortising attachment
> for a drill press, or would a dedicated benchtop mortising tool be a better
> route to go? Either tool would be something that would see future use,
> although I don't anticipate that volume of doors at any one time again. I
> currently use a forstner bit, for mortises, looking for something quicker.
> thanks.
For raised panel doors you would be much better off using a rail and stile
bit set with a router. A panel raising bit will do a good job making the
raised panels too and you can buy a bit set that includes all three. You'll
need a router table and a 3 HP router to run the raised panel bit though,
and it would be a good idea to use a router table when cutting the rails and
stiles too.
--
Charley
"Dan Williams" <[email protected]> wrote in message
news:[email protected]...
> I'll soon be working on building new kitchen cabinets. It will involve 24
or
> so frame and raised panel doors. That's about 100 mortise and tenon
joints.
> Does anyone have anything good to say about the Delta mortising attachment
> for a drill press, or would a dedicated benchtop mortising tool be a
better
> route to go? Either tool would be something that would see future use,
> although I don't anticipate that volume of doors at any one time again. I
> currently use a forstner bit, for mortises, looking for something quicker.
> thanks.
>
>
I did the kitchen door thing, 21 + another 5 in the pantry
I did the mortises with a dedicated mortiser. I like my mortiser, but if I
were to do it again I would just do with stub tenons formed by a rail and
stile cutter set. just because it would be a whole lot faster and the I'm
not convinced that the true M&T is warrented in a kitchen .... kitchens are
disposable (by heirloom furniture standards). They only have to last about
20 years before someone will want to remodel.
As for the drill press attachment, I had one and never could get it to work
satisfactorily.... Others have had better luck.
-Steve
"Dan Williams" <[email protected]> wrote in message
news:[email protected]...
> I'll soon be working on building new kitchen cabinets. It will involve 24
or
> so frame and raised panel doors. That's about 100 mortise and tenon
joints.
> Does anyone have anything good to say about the Delta mortising attachment
> for a drill press, or would a dedicated benchtop mortising tool be a
better
> route to go? Either tool would be something that would see future use,
> although I don't anticipate that volume of doors at any one time again. I
> currently use a forstner bit, for mortises, looking for something quicker.
> thanks.
>
>
The mortising attachment for drill press does not works as good as a real
mortising machine.
If you have a router and a carbide be you would be better off to make a jig
and fixture to make your mortising.
If not you can buy a made in china mortiser for around $200.00 CAD.
"Dan Williams" <[email protected]> wrote in message
news:[email protected]...
> I'll soon be working on building new kitchen cabinets. It will involve 24
> or so frame and raised panel doors. That's about 100 mortise and tenon
> joints. Does anyone have anything good to say about the Delta mortising
> attachment for a drill press, or would a dedicated benchtop mortising tool
> be a better route to go? Either tool would be something that would see
> future use, although I don't anticipate that volume of doors at any one
> time again. I currently use a forstner bit, for mortises, looking for
> something quicker. thanks.
>