Second "Machines are Heavy" thread in a day.
I've got a chance to buy a used Jet 14" saw (not sure which model yet)
but I think I'm going to have to move it myself. The seller is a widow
and, unless they've slipped some steroids into her hormone therapy, is
unlikely to be of much help.
Size isn't a problem (my wife just coughed for some reason) but weight
is, I don't think I could lift it alone into my van. I think my best
bet is to disassemble the saw into smaller parts and move the parts.
Never having been closer than four inches (coughed again, must be
allergies) to a bandsaw, I have no idea how much they can be broken
down, and what the best strategy for reducing the weight might be. Can
the table be removed? Can the wheels be taken out? Can the top arm be
separated from the bottom? Should I prop it on skateboards and drag it
behind my car?
I appreciate any help that can be offered. I'd enlist some friends to
help my move it, but the fact that I'm here posting on the internet
should give you a sense of how many friends I have. Perhaps it's my
attitude. Anyway, thanks!
I would download the JET manual for this and see how the
thing was assembled and follow the reverse of that to get
into pieces.
If you WANT to move it whole, why not see if a local moving
company will do it? Sometimes these guys finish early in
the day and might want to make a quick dollar.
Just a suggestion. Watch your back!
MJ Wallace
[email protected] wrote:
> Second "Machines are Heavy" thread in a day.
>
> I've got a chance to buy a used Jet 14" saw (not sure which model yet)
> but I think I'm going to have to move it myself. The seller is a widow
> and, unless they've slipped some steroids into her hormone therapy, is
> unlikely to be of much help.
>
> Size isn't a problem (my wife just coughed for some reason) but weight
> is, I don't think I could lift it alone into my van. I think my best
> bet is to disassemble the saw into smaller parts and move the parts.
> Never having been closer than four inches (coughed again, must be
> allergies) to a bandsaw, I have no idea how much they can be broken
> down, and what the best strategy for reducing the weight might be. Can
> the table be removed? Can the wheels be taken out? Can the top arm be
> separated from the bottom? Should I prop it on skateboards and drag it
> behind my car?
They aren't all that heavy...around 100#. Taking off the motor would reduce
the weight the most followed by the table.
--
dadiOH
____________________________
dadiOH's dandies v3.06...
...a help file of info about MP3s, recording from
LP/cassette and tips & tricks on this and that.
Get it at http://mysite.verizon.net/xico
How strong do you feel, and how far do you have to move it? I've moved my
14" Delta, with the riser kit on it a few times. Some things to note:
1) My bandsaw could get taken off it's base pretty easy.
2) The motor also comes off pretty easy, but I'd probably avoid doing this,
because it's a real bugger to get it back in place.
3) Use your head, not your back (where-ever possible). Think about getting
a mobile base for it, and using that to move it around. Back your van up as
close as you can to it, and gently ease it over, then slide it around. And
so on...
Having said all that, the top part of the bandsaw (with both wheels, etc)
is, I'm guessing about 2/3 to 3/4 of the total weight. Out of a 200 pound
bandsaw, that's what, 120 to 150 pounds? It's awkward to move, it will
crush fingers (DAMHIKT) if you're not careful setting it down, and it's not
much fun to move by yourself, especially up a flight of stairs. I don't
think you'll save much weight by taking the wheels off, but if you separate
the top section from the bottom, you'll get a reasonable division of the
weight, I think. Bottom part will probalby still be heavier, but not too
bad. Table is easy to remove and put back on, though.
Clint
<[email protected]> wrote in message
news:[email protected]...
> Second "Machines are Heavy" thread in a day.
>
> I've got a chance to buy a used Jet 14" saw (not sure which model yet)
> but I think I'm going to have to move it myself. The seller is a widow
> and, unless they've slipped some steroids into her hormone therapy, is
> unlikely to be of much help.
>
> Size isn't a problem (my wife just coughed for some reason) but weight
> is, I don't think I could lift it alone into my van. I think my best
> bet is to disassemble the saw into smaller parts and move the parts.
> Never having been closer than four inches (coughed again, must be
> allergies) to a bandsaw, I have no idea how much they can be broken
> down, and what the best strategy for reducing the weight might be. Can
> the table be removed? Can the wheels be taken out? Can the top arm be
> separated from the bottom? Should I prop it on skateboards and drag it
> behind my car?
>
> I appreciate any help that can be offered. I'd enlist some friends to
> help my move it, but the fact that I'm here posting on the internet
> should give you a sense of how many friends I have. Perhaps it's my
> attitude. Anyway, thanks!
>
[email protected] wrote in news:1149615410.120167.26170
@c74g2000cwc.googlegroups.com:
> Second "Machines are Heavy" thread in a day.
>
> I've got a chance to buy a used Jet 14" saw ...
> but I think I'm going to have to move it myself.
Been there done that. Jet 14" Bandsaw with riser kit and jet 1236 lathe.
Bandsaw was on mobile base, rolled it out of garage to pu-truck and tipped
it in. Lathe was disaasembled off the base. Had some help to pick lathe to
slide in. Only problem was breaking the "plastic ears" off the bandsaw
pushbutton switch during transit. Tipped bandsaw out of truck myself onto
mobile base in the garage. Had someone help ease lathe on base in garage.
During the next several weeks had my daughter (25) help carry lathe
downstairs to shop ^h^h^h^h basement. Later, son (27) helped with bandsaw
up four steps and down a full flight. No dissassembly, just took off the
fence & took all the blades and crap out of the base. It is top heavy, but
with a handtruck and straps it is not a real problem.
HTH
Jerry
:) Yeah, my bandsaw is missing the cover of my plastic safety switch too,
after a move. It was a choice of setting it down on the side with the
switch, or the pulleys, and I chose the switch. I'd do it again, too. I
think the useless vacuum port got busted in one of the moves, too.
Clint
"A Lurker" <[email protected]> wrote in message
news:[email protected]...
> [email protected] wrote in news:1149615410.120167.26170
> @c74g2000cwc.googlegroups.com:
>
>> Second "Machines are Heavy" thread in a day.
>>
>> I've got a chance to buy a used Jet 14" saw ...
>> but I think I'm going to have to move it myself.
>
> Been there done that. Jet 14" Bandsaw with riser kit and jet 1236 lathe.
> Bandsaw was on mobile base, rolled it out of garage to pu-truck and tipped
> it in. Lathe was disaasembled off the base. Had some help to pick lathe
> to
> slide in. Only problem was breaking the "plastic ears" off the bandsaw
> pushbutton switch during transit. Tipped bandsaw out of truck myself onto
> mobile base in the garage. Had someone help ease lathe on base in garage.
> During the next several weeks had my daughter (25) help carry lathe
> downstairs to shop ^h^h^h^h basement. Later, son (27) helped with bandsaw
> up four steps and down a full flight. No dissassembly, just took off the
> fence & took all the blades and crap out of the base. It is top heavy, but
> with a handtruck and straps it is not a real problem.
>
> HTH
>
> Jerry
The table top and motor should not be too tough to remove and will account
for a fair amount of weight. If there is an integrated stand, that might be
worth removing just to make the main casting that much easier to remove.
-Steve
<[email protected]> wrote in message
news:[email protected]...
> Second "Machines are Heavy" thread in a day.
>
> I've got a chance to buy a used Jet 14" saw (not sure which model yet)
> but I think I'm going to have to move it myself. The seller is a widow
> and, unless they've slipped some steroids into her hormone therapy, is
> unlikely to be of much help.
>
> Size isn't a problem (my wife just coughed for some reason) but weight
> is, I don't think I could lift it alone into my van. I think my best
> bet is to disassemble the saw into smaller parts and move the parts.
> Never having been closer than four inches (coughed again, must be
> allergies) to a bandsaw, I have no idea how much they can be broken
> down, and what the best strategy for reducing the weight might be. Can
> the table be removed? Can the wheels be taken out? Can the top arm be
> separated from the bottom? Should I prop it on skateboards and drag it
> behind my car?
>
> I appreciate any help that can be offered. I'd enlist some friends to
> help my move it, but the fact that I'm here posting on the internet
> should give you a sense of how many friends I have. Perhaps it's my
> attitude. Anyway, thanks!
>
In article <[email protected]>,
[email protected] wrote:
> I have no idea how much they can be broken
> down, and what the best strategy for reducing the weight might be. Can
> the table be removed? Can the wheels be taken out? Can the top arm be
> separated from the bottom? Should I prop it on skateboards and drag it
> behind my car?
Having just moved a 700 pound band saw, I think I can offer a few tips.
The absolutely easiest way would be to beg, borrow, rent or steal a
utility trailer and heavy-duty appliance dolly. The appliance dolly
needs to be one with the auxiliary wheels at the back that can be
extended for support. You should be able to muscle the Jet band saw
around with this setup fairly easily - these only weigh about 200 lbs.
They are a tad top-heavy, so just be aware of that when you tip it back.
<http://users.easystreet.com/onlnlowe/misc/DAVISwellsBANDsaw/AsUnloaded.j
pg>
If you must do without the trailer and dolly, I'd recommend taking the
table off (loosen and remove the two tilt/angle knobs on the underside
of the table - the table should lift straight up off the trunnions);
remove the drive belt from the motor and then unbolt the upper assembly
from the base. With those three components separated, you shouldn't have
too much trouble lifting by yourself.
I'd not separate the upper arm casting from the lower casting - just too
much trouble and I don't think it's necessary - and I'm a 180 lb
weakling... If you do decide to go this route, make sure you have a BIG
wrench to fit the bolt and nut.
--
Owen Lowe
The Fly-by-Night Copper Company
__________
"I pledge allegiance to the flag of the
Corporate States of America and to the
Republicans for which it stands, one nation,
under debt, easily divisible, with liberty
and justice for oil."
- Wiley Miller, Non Sequitur, 1/24/05
The Jet weighs about the same as the Grizzly G0555 - a little over 200#.
It's a bit top heavy but if you have an appliance dolly - should be no
problem. If you plan ahead, you should be able to get it to the van and use
the top heavy feature to tilt it on it's side and slide it into the van. If
you use leverage properly, you should have no problem and not have to
dismantle the saw.
HTH
<[email protected]> wrote in message
news:[email protected]...
> Second "Machines are Heavy" thread in a day.
>
> I've got a chance to buy a used Jet 14" saw (not sure which model yet)
> but I think I'm going to have to move it myself. The seller is a widow
> and, unless they've slipped some steroids into her hormone therapy, is
> unlikely to be of much help.
>
> Size isn't a problem (my wife just coughed for some reason) but weight
> is, I don't think I could lift it alone into my van. I think my best
> bet is to disassemble the saw into smaller parts and move the parts.
> Never having been closer than four inches (coughed again, must be
> allergies) to a bandsaw, I have no idea how much they can be broken
> down, and what the best strategy for reducing the weight might be. Can
> the table be removed? Can the wheels be taken out? Can the top arm be
> separated from the bottom? Should I prop it on skateboards and drag it
> behind my car?
>
> I appreciate any help that can be offered. I'd enlist some friends to
> help my move it, but the fact that I'm here posting on the internet
> should give you a sense of how many friends I have. Perhaps it's my
> attitude. Anyway, thanks!
>