On Dec 21, 8:18 pm, "Jack" <[email protected]> wrote:
> I need a drive for a 5 hp motor. The 30hp cost $2000.00 three years
> ago. I'll find one.
Check eBay.
JP
In article <[email protected]>,
Jack <[email protected]> wrote:
>Anyone know of a source for 1 ph to 3 ph vfd drives that are cheap.
>I've installed 30hp 1 ph to 3 ph Sq. D drives on machines before for
>friends, but I don't have the source they had. Jack
Of new equipment, AFAIK AutomationDirect (search on the web, probably
www.automationdirect.com) has the best deal. They have 2 or 3 lines
of VFDs. The largest 1ph to 3ph converters are 3HP; above that they
only have VFDs with 3 phase input.
Does anyone know of VFDs with 1ph input and 3ph output that are larger
than 3HP (typically 10-11A at 220V)? I haven't done an exhaustive
search, but have not found any VFDs that can be used on 1ph input
larger than 3HP.
In used equipment, there are many sources. Obviously ebay. There are
also several dealers that specialize in used equipment. The way I
work it: Find the manufacturer that makes the equipment, then find
used dealers for the equipment using google.
Good luck!
--
The address in the header is invalid for obvious reasons. Please
reconstruct the address from the information below (look for _).
Ralph Becker-Szendy _firstname_@lr_dot_los-gatos_dot_ca.us
Try your local SquareD distributor again and ask to see literature on the
Altivar 11 series. Reasonably priced and go from 1/4hp to 1hp. If you need a
larger size the Altivar 31 goes from 1/4hp to 3 hp. If you are looking to
control a larger yet size, the Altivar 71 will go up to a 7.5hp.. Also what
are you trying to do with it? If you are looking to run a 3ph. motor with a
1ph drive, it maybe a waste of money. Cheap drives burn up quite easily.
Allen
"Jack" <[email protected]> wrote in message
news:[email protected]...
> Anyone know of a source for 1 ph to 3 ph vfd drives that are cheap.
> I've installed 30hp 1 ph to 3 ph Sq. D drives on machines before for
> friends, but I don't have the source they had. Jack
>
Jack,
Try this:
http://web2.automationdirect.com/adc/Shopping/Catalog/AC_Drives_-z-_Motors
You didn't mention what size you need, but a 1 HP 230 volt, single phase
input, three phase output drive is $125.00 (GS1-21PO).
Regards,
Rick
"Jack" <[email protected]> wrote in message
news:[email protected]...
> Anyone know of a source for 1 ph to 3 ph vfd drives that are cheap.
> I've installed 30hp 1 ph to 3 ph Sq. D drives on machines before for
> friends, but I don't have the source they had. Jack
>
Jack,
Again,
http://web2.automationdirect.com/adc/Shopping/Catalog/AC_Drives_-z-_Motors
The GS2-25PO is 5 HP, 230 V 3ph in, 230V 3ph out ... $339.00.
Merry Christmas,
Rick
"Jack" <[email protected]> wrote in message
news:[email protected]...
>
> I need a drive for a 5 hp motor. The 30hp cost $2000.00 three years
> ago. I'll find one.
>
_firstname_@lr_dot_los-gatos_dot_ca.us (in 1166839545.69032@smirk)
said:
| Does anyone know of VFDs with 1ph input and 3ph output that are
| larger than 3HP (typically 10-11A at 220V)? I haven't done an
| exhaustive search, but have not found any VFDs that can be used on
| 1ph input larger than 3HP.
I have a Delta (VFD-B, I think) single phase input / three phase
output rated for 7-1/2 HP. I use it with a 5 HP spindle on a ShopBot
and have been happy with it. You can see it in the second and fourth
photos on the web page at the link below (it has a beige case with
black single phase cable, an orange three-phase cable, and a phone
wire.) I think I have a better photo somewhere - let me know if you're
interested in seeing it.
--
Morris Dovey
DeSoto Solar
DeSoto, Iowa USA
http://www.iedu.com/DeSoto/collectors.html
Jack (in [email protected]) said:
| I knew that Sq. D. used to make up to 30hp in a 1ph to 3 ph vfd but
| I didn't know Delta drive made them that big. The Delta machines
| 43-255x lathe has a 2 hp Delta drive ( made by Delta drives) on
| it. I'll look into their line of drives. Thanks everyone, Merry
| Christmas.
I went digging through a pile of photos last night and found one of
the Delta VFD-B - and it seems that I didn't quite have the capacity
right. It's rated for 10hp rather than 7-1/2. I'll post a photo of the
whole thing on abpw with a close-up of the output rating.
--
Morris Dovey
DeSoto Solar
DeSoto, Iowa USA
http://www.iedu.com/DeSoto
What size?
"Jack" <[email protected]> wrote in message
news:[email protected]...
> Anyone know of a source for 1 ph to 3 ph vfd drives that are cheap.
> I've installed 30hp 1 ph to 3 ph Sq. D drives on machines before for
> friends, but I don't have the source they had. Jack
>