"Maskman" <[email protected]> wrote in message news:<CSI0d.29138$D%.3360@attbi_s51>...
> In the most recent issue of Fine Woodworking there is an article on building
> a collapsable panel saw. Does anyone know of any other designs, plans, etc.
> out there?
> Thanks a lot,
> Jer
I built a panel saw that is on wheels, similar to saws you see in the
home centers. It is not collaspable but stores along a wall. Uses
sliding door rails and hardware to guide the saw. Accurate, dead
square crosscuts. I do not rip with the panel saw as I have a cabinet
saw for ripping. Last year I had a job that required almost 300
crosscuts in oak plywood, thus building a panel saw.If you anticipate
a lot of crosscutting sheet goods, then a panelsaw is very handy.I
probably could figure out a way to rip with my saw without removing
the saw and turning it 90 degrees on the mdf base.I might lose
accuracy of crosscuts though.
mike
On 11 Sep 2004 21:48:06 -0700, "Bob" <[email protected]> wrote:
>I've never understood the relative value of one of the homemade panel
>saws. They take up a lot of space, even when folded. I screw a couple
>of 7 foot 2x4 boards to the wooden tops of my two sawhorses and lay the
>panel on top of them. I adjust the blade of my circular saw to cut
>about 1/4" deeper than the thickness of the plywood or Mdf panel (thus
>cutting into the 2x4 boards. Its fast and doesn't take up a lot of
>space when stored.
>
>Bob
That works well, but I've found something works even better for me.
I put the sheet goods on the floor, on foam insulation, and simply
kneel on the sheet with my Makita trim saw. The 2'x8' foam sheets
easily store in my garage rafters, or outside, under my deck. One
could easily cut the foam into whatever size stores the easiest for
them.
I picked this technique up here on the 'wreck a few years back and
have yet to go back to sawhorses.
Barry
On 11 Sep 2004 21:48:06 -0700, "Bob" <[email protected]> calmly
ranted:
>I've never understood the relative value of one of the homemade panel
>saws. They take up a lot of space, even when folded. I screw a couple
>of 7 foot 2x4 boards to the wooden tops of my two sawhorses and lay the
>panel on top of them. I adjust the blade of my circular saw to cut
>about 1/4" deeper than the thickness of the plywood or Mdf panel (thus
>cutting into the 2x4 boards. Its fast and doesn't take up a lot of
>space when stored.
Ditto with scrap strips of 1" insulating foam panels and
a $20 StrateCut(tm) aluminum channel guide. No fuss, no
muss, easy storage.
-------------------------------------------------------
Have you read the new book "What Would Machiavelli Do?"
----------------------------
http://diversify.com Dynamic, Interactive Websites!
--------------------------------------------------------
One of the first ShopNotes has plans for a panel saw. Just guessing I'd say
#4. I pretty much went into Homedepo and copied one of theirs.
http://www.sawtrax.com/
Is pretty similar to the ShopNotes version. And just parts
http://www.sawtrax.com/Page3.html
Joel. phx
And there were 24,400 hits on 'panel saw plans' for a google group search.
"Maskman" <[email protected]> wrote in message
news:CSI0d.29138$D%.3360@attbi_s51...
> In the most recent issue of Fine Woodworking there is an article on
building
> a collapsable panel saw. Does anyone know of any other designs, plans,
etc.
> out there?
> Thanks a lot,
> Jer
>
>
>
And perhaps I should clarify; it would be a design using a portable circular
saw.
Thanks again.
"Maskman" <[email protected]> wrote in message
news:CSI0d.29138$D%.3360@attbi_s51...
> In the most recent issue of Fine Woodworking there is an article on
> building
> a collapsable panel saw. Does anyone know of any other designs, plans,
> etc.
> out there?
> Thanks a lot,
> Jer
>
>
>
I still think the key factor is what you need to do. In the last project I had
3-4 sheets to cut up, and just did it over a bed of 2x4s. The next project
will need about 15 sheets of 3/4 ply and I'm waiting until I can see the
cutting diagrams to decide if it justifies a panel saw. If I had several times
that number of sheets, there wouldn't be any question.
Yes, it could still be done with a straight ends and 2x4s. But then I really
wouldn't need a table saw, either. The reason I have one is because of the
number of rips I typically need. Same with a panel saw if the number of wide
crosscuts grows enough.
It also seems to me that you could make one that would break down into 3-4
pices, yet be easily assembled and aligned. Maybe that'll be the next project,
instead.
GerryG
On Mon, 13 Sep 2004 22:27:38 GMT, "Maskman" <[email protected]> wrote:
>I like this idea. Thanks.
>"Larry Jaques" <novalidaddress@di\/ersify.com> wrote in message
>news:[email protected]...
>> On 11 Sep 2004 21:48:06 -0700, "Bob" <[email protected]> calmly
>> ranted:
>>
>>>I've never understood the relative value of one of the homemade panel
>>>saws. They take up a lot of space, even when folded. I screw a couple
>>>of 7 foot 2x4 boards to the wooden tops of my two sawhorses and lay the
>>>panel on top of them. I adjust the blade of my circular saw to cut
>>>about 1/4" deeper than the thickness of the plywood or Mdf panel (thus
>>>cutting into the 2x4 boards. Its fast and doesn't take up a lot of
>>>space when stored.
>>
>> Ditto with scrap strips of 1" insulating foam panels and
>> a $20 StrateCut(tm) aluminum channel guide. No fuss, no
>> muss, easy storage.
>>
>>
>> -------------------------------------------------------
>> Have you read the new book "What Would Machiavelli Do?"
>> ----------------------------
>> http://diversify.com Dynamic, Interactive Websites!
>> --------------------------------------------------------
>>
>
I like this idea. Thanks.
"Larry Jaques" <novalidaddress@di\/ersify.com> wrote in message
news:[email protected]...
> On 11 Sep 2004 21:48:06 -0700, "Bob" <[email protected]> calmly
> ranted:
>
>>I've never understood the relative value of one of the homemade panel
>>saws. They take up a lot of space, even when folded. I screw a couple
>>of 7 foot 2x4 boards to the wooden tops of my two sawhorses and lay the
>>panel on top of them. I adjust the blade of my circular saw to cut
>>about 1/4" deeper than the thickness of the plywood or Mdf panel (thus
>>cutting into the 2x4 boards. Its fast and doesn't take up a lot of
>>space when stored.
>
> Ditto with scrap strips of 1" insulating foam panels and
> a $20 StrateCut(tm) aluminum channel guide. No fuss, no
> muss, easy storage.
>
>
> -------------------------------------------------------
> Have you read the new book "What Would Machiavelli Do?"
> ----------------------------
> http://diversify.com Dynamic, Interactive Websites!
> --------------------------------------------------------
>