MM

Mike M

29/11/2012 7:43 PM

Ibox, Leon

Finally got a chance to play with it. Had a little trouble getting
set up as I have a right tilt saw. But got throught that and first
pass my joints are too tight, and too deep, Any suggestions? Damn
Xmas is coming fast and I'm hoping to do boxes. Using the Frued box
joint blade. Using 3/8" setting and using scrap still. Too deep
should be easy to cure but not sure on the tighgtness. My senses tell
me to open the fingers. Any advice

Mike M


This topic has 4 replies

Cc

"CW"

in reply to Mike M on 29/11/2012 7:43 PM

30/11/2012 1:46 AM



"Mike M" wrote in message
news:[email protected]...

Finally got a chance to play with it. Had a little trouble getting
set up as I have a right tilt saw. But got throught that and first
pass my joints are too tight, and too deep, Any suggestions? Damn
Xmas is coming fast and I'm hoping to do boxes. Using the Frued box
joint blade. Using 3/8" setting and using scrap still. Too deep
should be easy to cure but not sure on the tighgtness. My senses tell
me to open the fingers. Any advice
=========================================================================
The slots will remain the same so the thing to do is make the fingers
narrower.

MM

Mike M

in reply to Mike M on 29/11/2012 7:43 PM

01/12/2012 2:17 AM

On Fri, 30 Nov 2012 18:08:33 -0600, Leon <lcb11211@swbelldotnet>
wrote:

>On 11/29/2012 9:43 PM, Mike M wrote:
>> Finally got a chance to play with it. Had a little trouble getting
>> set up as I have a right tilt saw. But got throught that and first
>> pass my joints are too tight, and too deep, Any suggestions? Damn
>> Xmas is coming fast and I'm hoping to do boxes. Using the Frued box
>> joint blade. Using 3/8" setting and using scrap still. Too deep
>> should be easy to cure but not sure on the tighgtness. My senses tell
>> me to open the fingers. Any advice
>>
>> Mike M
>>
>
>
>Ummm did you read the directions? LOL
>
>Too deep , lower the blade.
>
>Too tight widen the spacing a touch. should be a simple process to
>figure out..

Mostly watching the DVD. All so girl friend wants to borrow money.
I've been very distracted. I figure little slave girl is worth
several points of interest.

MM

Mike M

in reply to Mike M on 29/11/2012 7:43 PM

30/11/2012 11:08 AM

On Fri, 30 Nov 2012 01:46:03 -0800, "CW" <[email protected]> wrote:

>
>
>"Mike M" wrote in message
>news:[email protected]...
>
>Finally got a chance to play with it. Had a little trouble getting
>set up as I have a right tilt saw. But got throught that and first
>pass my joints are too tight, and too deep, Any suggestions? Damn
>Xmas is coming fast and I'm hoping to do boxes. Using the Frued box
>joint blade. Using 3/8" setting and using scrap still. Too deep
>should be easy to cure but not sure on the tighgtness. My senses tell
>me to open the fingers. Any advice
>=========================================================================
>The slots will remain the same so the thing to do is make the fingers
>narrower.

I agree, however just leaning to use this jig I'll have to experiment.
In a previous post Leon made it sound like a very close to no kiss was
the answer. So I guess I experiment.

Ll

Leon

in reply to Mike M on 29/11/2012 7:43 PM

30/11/2012 6:08 PM

On 11/29/2012 9:43 PM, Mike M wrote:
> Finally got a chance to play with it. Had a little trouble getting
> set up as I have a right tilt saw. But got throught that and first
> pass my joints are too tight, and too deep, Any suggestions? Damn
> Xmas is coming fast and I'm hoping to do boxes. Using the Frued box
> joint blade. Using 3/8" setting and using scrap still. Too deep
> should be easy to cure but not sure on the tighgtness. My senses tell
> me to open the fingers. Any advice
>
> Mike M
>


Ummm did you read the directions? LOL

Too deep , lower the blade.

Too tight widen the spacing a touch. should be a simple process to
figure out..


You’ve reached the end of replies