Leon <lcb11211@swbelldotnet> wrote in news:OfqdncWIeL_FnhPFnZ2dnUU7-
[email protected]:
>
> All true but he really does not care what any of us think about his
> comments. He only wants to suck us for information and never takes any
> advice. He believes he is much smarter than any of us on woodworking
> although hes has yet to show any thing he has done. I really do not
> think he does anything at all.
>
>
There is one thing EC does... He fills the newsgroup with woodworking
comments. Sometimes we get so busy chatting with each other, we forget
that this group is about woodworking.
Puckdropper
--
http://www.puckdroppersplace.us/rec.woodworking
A mini archive of some of rec.woodworking's best and worst!
On 1/29/2017 8:04 AM, Larry Kraus wrote:
> On 1/28/2017 5:01 PM, Electric Comet wrote:
>>
>> first setup gave me a convex curved bottom cut
>>
>> swapped the outside blades and now i get a flat bottom cut
>>
>> seemed logical to place the labeled sides
>>
>> under no load the 6 inch dado set is much quieter than my regular
>> blade and thought it would make more noise
>>
>>
>
>
>
> Most of us can deal with a lack of capital letters.
>
> A few will try to sort words without punctuation into coherent units,
> though the result will likely be different than you might have intended.
>
> But when you leave out entire words, we are left with gibberish.
>
All true but he really does not care what any of us think about his
comments. He only wants to suck us for information and never takes any
advice. He believes he is much smarter than any of us on woodworking
although hes has yet to show any thing he has done. I really do not
think he does anything at all.
On Sun, 29 Jan 2017 09:04:58 -0500, Larry Kraus <[email protected]>
wrote:
>On 1/28/2017 5:01 PM, Electric Comet wrote:
>>
>> first setup gave me a convex curved bottom cut
>>
>> swapped the outside blades and now i get a flat bottom cut
>>
>> seemed logical to place the labeled sides
>>
>> under no load the 6 inch dado set is much quieter than my regular
>> blade and thought it would make more noise
>>
>>
>
>
>
>Most of us can deal with a lack of capital letters.
>
>A few will try to sort words without punctuation into coherent units,
>though the result will likely be different than you might have intended.
>
>But when you leave out entire words, we are left with gibberish.
>
With all the words, punctuation and capitalization, most of it would
still be gibberish.
>
>
>
On 1/28/2017 5:01 PM, Electric Comet wrote:
>
> first setup gave me a convex curved bottom cut
>
> swapped the outside blades and now i get a flat bottom cut
>
> seemed logical to place the labeled sides
>
> under no load the 6 inch dado set is much quieter than my regular
> blade and thought it would make more noise
>
>
Most of us can deal with a lack of capital letters.
A few will try to sort words without punctuation into coherent units,
though the result will likely be different than you might have intended.
But when you leave out entire words, we are left with gibberish.
On 1/29/2017 10:39 AM, Puckdropper wrote:
> Leon <lcb11211@swbelldotnet> wrote in news:OfqdncWIeL_FnhPFnZ2dnUU7-
> [email protected]:
>>
>> All true but he really does not care what any of us think about his
>> comments. He only wants to suck us for information and never takes any
>> advice. He believes he is much smarter than any of us on woodworking
>> although hes has yet to show any thing he has done. I really do not
>> think he does anything at all.
>>
> There is one thing EC does... He fills the newsgroup with woodworking
> comments. Sometimes we get so busy chatting with each other, we forget
> that this group is about woodworking.
Exactly. He starts most of the threads in this group now, giving those
that think they know everything, and the english school marms a chance
to spout off. I went through the subjects the other day it most of
them were started by EC.
Oh, the other thing he does that is somewhat impressive, he ignores ALL
smarmy responses to his posts, and they are abundant, particularly from
the english school marms and those that know little and need a chance to
bitch.
He might be the only reason this group still lives...
--
Jack
Add Life to your Days not Days to your Life.
http://jbstein.com
On 1/29/2017 4:46 PM, [email protected] wrote:
> On Sun, 29 Jan 2017 09:04:58 -0500, Larry Kraus <[email protected]>
> wrote:
>
>> On 1/28/2017 5:01 PM, Electric Comet wrote:
>>>
>>> first setup gave me a convex curved bottom cut
>>>
>>> swapped the outside blades and now i get a flat bottom cut
>>>
>>> seemed logical to place the labeled sides
>>>
>>> under no load the 6 inch dado set is much quieter than my regular
>>> blade and thought it would make more noise
>>>
>>>
>>
>>
>>
>> Most of us can deal with a lack of capital letters.
>>
>> A few will try to sort words without punctuation into coherent units,
>> though the result will likely be different than you might have intended.
>>
>> But when you leave out entire words, we are left with gibberish.
>>
> With all the words, punctuation and capitalization, most of it would
> still be gibberish.
>
>>
>>
>>
Let me try to interpret for those with little comprehension skills.
On first use he had the outside blades reversed, left blade on the
right, right blade on left. (This sounds hard to do unless you have a
Freud dado set.) After correcting this the dado cut had a flat bottom
and was quieter. On my Freud set, it is hard to figure the correct
placement of the chippers as well.
He missed a word to describe if he thought the label side should be in
or out, so if I were to insert a word, I'd say the label should be out,
but who knows, perhaps a few hundred messages will result from his
"gibberish".
--
Jack
Add Life to your Days not Days to your Life.
http://jbstein.com
On 1/30/2017 10:00 PM, [email protected] wrote:
> On Mon, 30 Jan 2017 09:41:11 -0500, Jack <[email protected]> wrote:
>
>> On 1/29/2017 10:39 AM, Puckdropper wrote:
>>> Leon <lcb11211@swbelldotnet> wrote in news:OfqdncWIeL_FnhPFnZ2dnUU7-
>>> [email protected]:
>>>>
>>>> All true but he really does not care what any of us think about his
>>>> comments. He only wants to suck us for information and never takes any
>>>> advice. He believes he is much smarter than any of us on woodworking
>>>> although hes has yet to show any thing he has done. I really do not
>>>> think he does anything at all.
>>>>
>>> There is one thing EC does... He fills the newsgroup with woodworking
>>> comments. Sometimes we get so busy chatting with each other, we forget
>>> that this group is about woodworking.
>>
>> Exactly. He starts most of the threads in this group now, giving those
>> that think they know everything, and the english school marms a chance
>> to spout off. I went through the subjects the other day it most of
>> them were started by EC.
>>
>> Oh, the other thing he does that is somewhat impressive, he ignores ALL
>> smarmy responses to his posts, and they are abundant, particularly from
>> the english school marms and those that know little and need a chance to
>> bitch.
>>
>> He might be the only reason this group still lives...
>
> No one is forcing you to stay.
>
WTF? You guys bitch constantly about the guy that keeps the group
alive. No one is forcing you to stay, idiot!
--
Jack
Add Life to your Days not Days to your Life.
http://jbstein.com
On Mon, 30 Jan 2017 09:41:11 -0500, Jack <[email protected]> wrote:
>On 1/29/2017 10:39 AM, Puckdropper wrote:
>> Leon <lcb11211@swbelldotnet> wrote in news:OfqdncWIeL_FnhPFnZ2dnUU7-
>> [email protected]:
>>>
>>> All true but he really does not care what any of us think about his
>>> comments. He only wants to suck us for information and never takes any
>>> advice. He believes he is much smarter than any of us on woodworking
>>> although hes has yet to show any thing he has done. I really do not
>>> think he does anything at all.
>>>
>> There is one thing EC does... He fills the newsgroup with woodworking
>> comments. Sometimes we get so busy chatting with each other, we forget
>> that this group is about woodworking.
>
>Exactly. He starts most of the threads in this group now, giving those
>that think they know everything, and the english school marms a chance
>to spout off. I went through the subjects the other day it most of
>them were started by EC.
>
>Oh, the other thing he does that is somewhat impressive, he ignores ALL
>smarmy responses to his posts, and they are abundant, particularly from
>the english school marms and those that know little and need a chance to
>bitch.
>
>He might be the only reason this group still lives...
No one is forcing you to stay.
On Tue, 31 Jan 2017 11:00:13 -0500, Jack <[email protected]> wrote:
>On 1/30/2017 10:00 PM, [email protected] wrote:
>> On Mon, 30 Jan 2017 09:41:11 -0500, Jack <[email protected]> wrote:
>>
>>> On 1/29/2017 10:39 AM, Puckdropper wrote:
>>>> Leon <lcb11211@swbelldotnet> wrote in news:OfqdncWIeL_FnhPFnZ2dnUU7-
>>>> [email protected]:
>>>>>
>>>>> All true but he really does not care what any of us think about his
>>>>> comments. He only wants to suck us for information and never takes any
>>>>> advice. He believes he is much smarter than any of us on woodworking
>>>>> although hes has yet to show any thing he has done. I really do not
>>>>> think he does anything at all.
>>>>>
>>>> There is one thing EC does... He fills the newsgroup with woodworking
>>>> comments. Sometimes we get so busy chatting with each other, we forget
>>>> that this group is about woodworking.
>>>
>>> Exactly. He starts most of the threads in this group now, giving those
>>> that think they know everything, and the english school marms a chance
>>> to spout off. I went through the subjects the other day it most of
>>> them were started by EC.
>>>
>>> Oh, the other thing he does that is somewhat impressive, he ignores ALL
>>> smarmy responses to his posts, and they are abundant, particularly from
>>> the english school marms and those that know little and need a chance to
>>> bitch.
>>>
>>> He might be the only reason this group still lives...
>>
>> No one is forcing you to stay.
>>
>WTF? You guys bitch constantly about the guy that keeps the group
>alive. No one is forcing you to stay, idiot!
You're whining right here, dumbass!