Hi All;
Am refinishing the inside of an Airstream trailer. Going to
use veneer throughout. Try to determine how to cut the two
ends of the trailer pieces. Looks like I will need at least six
pieces to make the complete curve at each end. Short of
using lots of tar paper for templates, just not sure how to go
about making straight wood fit into curved corners.
Thanks for your time and efforts.
Don
[email protected] wrote:
> Hi All;
> Am refinishing the inside of an Airstream trailer. Going to
> use veneer throughout. Try to determine how to cut the two
> ends of the trailer pieces. Looks like I will need at least six
> pieces to make the complete curve at each end. Short of
> using lots of tar paper for templates, just not sure how to go
> about making straight wood fit into curved corners.
> Thanks for your time and efforts.
>
> Don
If you know you need six pieces of veneer, you could tape them all to
the interior using double-stick tape. Obviously they'll overlap to
some extend, especially at the top and bottom.
Then, set up a self-leveling laser level which can draw a plumb line
for you, and position it one sixth of the way around the circumference
of the end of the trailer, and trace the line onto the veneer. Then
move it over another sixth, then another, until you've gotten all of
your lines traced onto the veneer. Then slice through the overlapping
layers.
Josh
It would appear that I have to spell it out for some people. Try to fallow
along. If he glues veneer directly to the aluminum shell of a trailer, it
will buckle, split and come off. He will end up with an expensive mess.
Coefficient of expansion of woold and aluminum is substantially different.
Consequently, the only way of doing this and making it work is to put it on
something besides the aluminum. Something more stable. Plain enough for you?
"Oleg Lego" <[email protected]> wrote in message
news:[email protected]...
> The CW entity posted thusly:
>
> >I'm wondering what he is gluing the veneer to and how he got it to fit.
>
> Uh, he didn't get it to fit. That's why he wants to know the best way
> to figure out the cuts.
>
Hi again;
Let me back up a little. I actually replace the plastic roof ends
with new aluminum sheets, five total at each end. I was going to
glue veneer to that. Found out as was stated earlier, that expansion
is enough different in the two materials the glue would not hold.
Another person has already done this kind of project but was not
too clear about templates and such. The new idea is to sheet metal
screw or rivot veneer onto the ribs of the trailer.
There is a real possibility of condensation being aluminum and all.
So by using a 1 inch spacer and thin insulation between the outside
shell and the veneer this will be minumized. Also applying three
coats of sealer on the back side of wood wil help. I found out with
the aluminum that what was is straight laying of the table becomes
concave when put into the trailer. Just don't know how to figure this
curving in advance. Looks like a trail and error sort of thing.
Thanks again for time and efforts and responses.
Don
You are lost, aren't you?
"Oleg Lego" <[email protected]> wrote in message
news:[email protected]...
> The CW entity posted thusly:
>
> >It would appear that I have to spell it out for some people. Try to
fallow
> >along.
>
> I follow just fine. I followed both things you said. They are
> completely different. Try to say what you mean.
>
>
You are going to need to use some kind of template or risk wasting a lot of
veneer.
You could use cardboard or pegboard type material which is easily available
in 4ft x 8 ft sheets. You could cut the largest rectangle which will fit in
the end and then use cardboad to get the curves to fill the gaps. I would
then transfer this to another piece or two of the pegboard type material
just so the final template was a single piece.
Sound like an interesting project.
Dave Paine.
<[email protected]> wrote in message
news:[email protected]...
> Hi All;
> Am refinishing the inside of an Airstream trailer. Going to
> use veneer throughout. Try to determine how to cut the two
> ends of the trailer pieces. Looks like I will need at least six
> pieces to make the complete curve at each end. Short of
> using lots of tar paper for templates, just not sure how to go
> about making straight wood fit into curved corners.
> Thanks for your time and efforts.
>
> Don
I'm wondering what he is gluing the veneer to and how he got it to fit.
"Tyke" <[email protected]> wrote in message
news:[email protected]...
> You are going to need to use some kind of template or risk wasting a lot
of
> veneer.
>
> You could use cardboard or pegboard type material which is easily
available
> in 4ft x 8 ft sheets. You could cut the largest rectangle which will fit
in
> the end and then use cardboad to get the curves to fill the gaps. I would
> then transfer this to another piece or two of the pegboard type material
> just so the final template was a single piece.
>
> Sound like an interesting project.
>
> Dave Paine.
>
>
> <[email protected]> wrote in message
> news:[email protected]...
> > Hi All;
> > Am refinishing the inside of an Airstream trailer. Going to
> > use veneer throughout. Try to determine how to cut the two
> > ends of the trailer pieces. Looks like I will need at least six
> > pieces to make the complete curve at each end. Short of
> > using lots of tar paper for templates, just not sure how to go
> > about making straight wood fit into curved corners.
> > Thanks for your time and efforts.
> >
> > Don
>
>
The CW entity posted thusly:
>"Oleg Lego" <[email protected]> wrote in message
>news:[email protected]...
>> The CW entity posted thusly:
>>
>> >It would appear that I have to spell it out for some people. Try to
>fallow
>> >along.
>>
>> I follow just fine. I followed both things you said. They are
>> completely different. Try to say what you mean.
>You are lost, aren't you?
Not at all.
On Sun, 11 Jun 2006 15:51:30 GMT, "CW" <[email protected]> wrote:
>It would appear that I have to spell it out for some people. Try to fallow
>along. If he glues veneer directly to the aluminum shell of a trailer, it
>will buckle, split and come off. He will end up with an expensive mess.
>Coefficient of expansion of woold and aluminum is substantially different.
>Consequently, the only way of doing this and making it work is to put it on
>something besides the aluminum. Something more stable. Plain enough for you?
>
>"Oleg Lego" <[email protected]> wrote in message
>news:[email protected]...
>> The CW entity posted thusly:
>>
>> >I'm wondering what he is gluing the veneer to and how he got it to fit.
>>
>> Uh, he didn't get it to fit. That's why he wants to know the best way
>> to figure out the cuts.
>>
>
I think he stated "re-finishing" and thus I would assume the backing
is the original from the factory at mfg....I've seen formed plywood
before but cannot recall if it was an Airstream or not.
In any case this is a challenging project.
On 12 Jun 2006 10:59:30 -0700, "Josh" <[email protected]> wrote:
>[email protected] wrote:
>> Hi All;
>> Am refinishing the inside of an Airstream trailer. Going to
>> use veneer throughout. Try to determine how to cut the two
>> ends of the trailer pieces. Looks like I will need at least six
>> pieces to make the complete curve at each end. Short of
>> using lots of tar paper for templates, just not sure how to go
>> about making straight wood fit into curved corners.
>> Thanks for your time and efforts.
>>
>> Don
>
>If you know you need six pieces of veneer, you could tape them all to
>the interior using double-stick tape. Obviously they'll overlap to
>some extend, especially at the top and bottom.
>
>Then, set up a self-leveling laser level which can draw a plumb line
>for you, and position it one sixth of the way around the circumference
>of the end of the trailer, and trace the line onto the veneer. Then
>move it over another sixth, then another, until you've gotten all of
>your lines traced onto the veneer. Then slice through the overlapping
>layers.
>
>Josh
Neat, I just am not very creative. Thanks for you response and all
of the others too.
Don
On Sat, 10 Jun 2006 22:33:46 -0700, [email protected] wrote:
>Hi All;
>Am refinishing the inside of an Airstream trailer. Going to
>use veneer throughout. Try to determine how to cut the two
>ends of the trailer pieces. Looks like I will need at least six
>pieces to make the complete curve at each end. Short of
>using lots of tar paper for templates, just not sure how to go
>about making straight wood fit into curved corners.
Templates are the way to go, but I wouldn't use tar paper! Red rosin
paper is fairly cheap and works nicely for templates.