For a shop, what's a good kind of storage system for odd pieces of sheet
goods: plywood, particle board, paneling, etc.? In other words, what
kind of rack would be a good system? I suppose we have about 20 linear
feet of wall space to use, and we'll store along the wall in the rack
arrangement.
--
(||) Nehmo (||)
Agree flat storage is best for the material but flat storage requires a lot
of floor space which is often just not available. Narrow vertical racks
(that are usually full) keep material in a vertical position and bowing is
not a problem.
Earl Creel
"Leon" <[email protected]> wrote in message
news:[email protected]...
>
> The best would be laying the panels flat.
>
- JKevorkian -
> If you have a truck and at least one able-bodied buddy, take a trip to your
> local Borg and round up one of the stray buggies some inconsiderate yahoo left
> in the parking lot.
- Nehmo -
Since it has wheels, I don't need a buddy. I could just tie a rope
between one and the trailer hich. Then drive home.
--
(||) Nehmo (||)
Well of course it depends on what you want to store. IF the dimensions of
the sheet material is no longer than eight feet and no wider than five feet
then a mobile rack(s) similar to what I built for myself should work well
for you. My rack is eight feet long, 35 inches deep and 12 inches wide. It
is open on both ends so material can be slid in from either end and if the
material is not too wide it can also be loaded/unloaded from the top. It is
on casters so one end can be pulled out from the wall for easier access. My
space is limited so when working on a large project I roll the rack clear
out of the shop. The floor is a couple of 2 x 6's the sides were made from 2
sheets of OSB. Would post a picture or two if anyone is interested.
Earl Creel
"Nehmo Sergheyev" <[email protected]> wrote in message
news:[email protected]...
> For a shop, what's a good kind of storage system for odd pieces of sheet
> goods: plywood, particle board, paneling, etc.? In other words, what
> kind of rack would be a good system? I suppose we have about 20 linear
> feet of wall space to use, and we'll store along the wall in the rack
> arrangement.
>
> --
> (||) Nehmo (||)
>
>
So how are you doing Earl?
"Earl Creel" <[email protected]> wrote in message
news:0A6Af.9089$NE.7977@dukeread12...
> Agree flat storage is best for the material but flat storage requires a
> lot of floor space which is often just not available. Narrow vertical
> racks (that are usually full) keep material in a vertical position and
> bowing is not a problem.
> Earl Creel
> "Leon" <[email protected]> wrote in message
> news:[email protected]...
>>
>> The best would be laying the panels flat.
>>
>
>
> For a shop, what's a good kind of storage system for odd pieces of sheet
> goods: plywood, particle board, paneling, etc.? In other words, what
> kind of rack would be a good system? I suppose we have about 20 linear
> feet of wall space to use, and we'll store along the wall in the rack
> arrangement.
I store my plywood on edge in the corner of my shop. I built a stud wall
about 2 feet from the side wall, then stand my plywood sheets on end
between the two walls (I have 9-1/2' ceilings). They rest on PT 2x6's laid
flat on the floor to keep the edges off the concrete.
This system only takes up about 2'x4' of floor space, and I can easily flip
though the various sheets to find the one I need. Then it's easy to take a
single sheet out without moving the others.
I have several sheets of material, so everything is held vertically. And, I
don't usually have full sheets around very long to worry about warping.
I have a wheeled cart I store in front of the plywood sheets, so the space
doesn't go to waste. When I need a sheet of plywood, I simply wheel out the
cart, then pull out the sheet I need.
I've been real happy with this system.
Anthony
"Leon" <[email protected]> wrote in message
news:[email protected]...
>
> "Nehmo Sergheyev" <[email protected]> wrote in message
> news:[email protected]...
>> For a shop, what's a good kind of storage system for odd pieces of sheet
>> goods: plywood, particle board, paneling, etc.? In other words, what
>> kind of rack would be a good system? I suppose we have about 20 linear
>> feet of wall space to use, and we'll store along the wall in the rack
>> arrangement.
>
>
> The best would be laying the panels flat.
For those left over pieces I have mine stored flat in a rack above my garage
door. There was nothing in that space and it is not in the way.
"Leon" <[email protected]> wrote in message
news:[email protected]...
> So how are you doing Earl?
>
Okay for an old man. Found an additional source for salvage material. It
is a Co. that builds roof and floor trusses. They generate huge amounts of
2 x 4 cut-offs. They have pointy ends and are not very long, after the
point is trimmed off, but long enough to make drawers and such. Some are
good enough that I can re-saw them down and get book matched material that
is over 5/8" thick. After a few passes through the old Kuster drum sander I
have good looking stock that is a strong 9/16" which is the thickness I like
to use for most drawer boxes. Projects like this keep me as busy as I want
to be.
Earl Creel
On Sat, 21 Jan 2006 05:18:04 -0500, JKevorkian
<[email protected]> wrote:
>If you have a truck and at least one able-bodied buddy, take a trip to your
>local Borg and round up one of the stray buggies some inconsiderate yahoo left
>in the parking lot.
Don't forget to rent the Load N' Go so it'll be easier to get home!
"Nehmo Sergheyev" <[email protected]> wrote in message
news:[email protected]...
> For a shop, what's a good kind of storage system for odd pieces of sheet
> goods: plywood, particle board, paneling, etc.? In other words, what
> kind of rack would be a good system? I suppose we have about 20 linear
> feet of wall space to use, and we'll store along the wall in the rack
> arrangement.
The best would be laying the panels flat.
On Fri, 20 Jan 2006 09:22:41 GMT, "Nehmo Sergheyev" <[email protected]> wrote:
>For a shop, what's a good kind of storage system for odd pieces of sheet
>goods: plywood, particle board, paneling, etc.? In other words, what
>kind of rack would be a good system? I suppose we have about 20 linear
>feet of wall space to use, and we'll store along the wall in the rack
>arrangement.
If you have a truck and at least one able-bodied buddy, take a trip to your
local Borg and round up one of the stray buggies some inconsiderate yahoo left
in the parking lot.
"Earl Creel" <[email protected]> wrote in message
news:e%9Af.9104$NE.1876@dukeread12...
> Okay for an old man. Found an additional source for salvage material. It
> is a Co. that builds roof and floor trusses. They generate huge amounts
> of 2 x 4 cut-offs. They have pointy ends and are not very long, after the
> point is trimmed off, but long enough to make drawers and such. Some are
> good enough that I can re-saw them down and get book matched material that
> is over 5/8" thick. After a few passes through the old Kuster drum sander
> I have good looking stock that is a strong 9/16" which is the thickness I
> like to use for most drawer boxes. Projects like this keep me as busy as
> I want to be.
> Earl Creel
Great. Sounds like a nice find. Sounds like they might make good cabinet
door panels or small boxes also.