I need an 1/8" chisel to clean up some cuts from a CNC machine, 1/8" in
diameter. I've got mainly Stanley chisels and am reasonably happy with
them, but my smallest is 1/4".
Do you guys have any suggestions? Is the typical length of the 1/8" chisel
going to be a problem trying to cut end grain? 1/8" would seem to be awful
flexible...
I was hoping to spend about $10, but a quick search on Amazon shows only
one chisel for that price, a new Irwin Marples that is leaving many
disappointed.
Alternatively, I have some W1 drill rod and a mill... I guess I could make
one but I've already got enough on my plate...
Puckdropper
notbob <[email protected]> wrote in
news:[email protected]:
> On 2016-05-12, Scott Lurndal <[email protected]> wrote:
>
>> Puckdropper <puckdropper(at)yahoo(dot)com> writes:
>
>>>I was hoping to spend about $10......
>
>> I have, and use, one of these:
>>
>> http://www.traditionalwoodworker.com/2mm-1_8-Bevel-Edge-Chisel-by-Two-
>> Cherries/productinfo/500-1502/
>
> This is closer to yer target expenditure and Narex has a very good
> rep. Considered by many to be a "best buy":
>
> <http://www.amazon.com/Narex-Woodworking-Cabinetmakers-Chisel-Handle/dp
> /B00V922QT6/ref=sr_1_2?ie=UTF8&qid=1463064904&sr=8-2&keywords=chisel+1%
> 2F8>
>
> ....0r....
>
> ttp://tinyurl.com/hwmvn33
>
> Still gotta pay shipping, but shouldn't cost more than a few $$.
> Definitely cheaper than the other recommended chisel. ;)
>
> nb
>
It's a 3mm chisel, but I think in this case it will work ok. My cuts are
actually 1 thou oversize, to give me a tight "push together" fit. I
might have to bump it up another thou or two for glue space.
As far as shipping goes, I've got Prime so don't have to worry about
that. Speaking of Prime, if you like How It's Made, look up "How Did
They Make That?". It's well worth watching!
Puckdropper
"Puckdropper" wrote in message
news:[email protected]...
>I need an 1/8" chisel to clean up some cuts from a CNC machine, 1/8" in
>diameter. I've got mainly Stanley chisels and am reasonably happy with
>them, but my smallest is 1/4".
>Do you guys have any suggestions? Is the typical length of the 1/8" chisel
>going to be a problem trying to cut end grain? 1/8" would seem to be awful
>flexible...
When I couldn't find one I bought a relatively flat sweep narrow carving
gouge and reshaped it... a #2 2MM as I recall. This option might provide
alternatives...
On 12 May 2016 13:49:45 GMT, Puckdropper
<puckdropper(at)yahoo(dot)com> wrote:
>I need an 1/8" chisel to clean up some cuts from a CNC machine, 1/8" in
>diameter. I've got mainly Stanley chisels and am reasonably happy with
>them, but my smallest is 1/4".
Expensive, but they are out there.
http://www.leevalley.com/en/wood/page.aspx?p=67689&cat=1,41504
On 12 May 2016 14:32:45 GMT, notbob <[email protected]> wrote:
>On 2016-05-12, [email protected] <[email protected]> wrote:
>
>> Expensive, but they are out there.
>>
>> http://www.leevalley.com/en/wood/page.aspx?p=67689&cat=1,41504
>
>Specially when buying one-at-a-time from Lee Valley. Try Amazon:
>
><http://www.amazon.com/Stanley-16-781-Sweetheart-Socket-Chisel/dp/B004TQGHOE/ref=sr_1_3?ie=UTF8&qid=1463063078&sr=8-3&keywords=Stanley+Sweetheart+Chisels>
>
>....or....
>
>http://tinyurl.com/haaoahb
>
>That chisel will cost you $46, w/ shipping, from LV. Whatever Amazon
>charges fer shipping, the total still hasta be less than $46. ;)
>
>nb
$ 32. US plus $ 9. shipping from LV.
< the web link above is Canadian $ 38.50 >
... still a lot more than the $ 20. + shipping on Amazon.
John T.
Puckdropper <puckdropper(at)yahoo(dot)com> writes:
>I need an 1/8" chisel to clean up some cuts from a CNC machine, 1/8" in
>diameter. I've got mainly Stanley chisels and am reasonably happy with
>them, but my smallest is 1/4".
>
>Do you guys have any suggestions? Is the typical length of the 1/8" chisel
>going to be a problem trying to cut end grain? 1/8" would seem to be awful
>flexible...
>
>I was hoping to spend about $10, but a quick search on Amazon shows only
>one chisel for that price, a new Irwin Marples that is leaving many
>disappointed.
>
>Alternatively, I have some W1 drill rod and a mill... I guess I could make
>one but I've already got enough on my plate...
>
>Puckdropper
I have, and use, one of these:
http://www.traditionalwoodworker.com/2mm-1_8-Bevel-Edge-Chisel-by-Two-Cherries/productinfo/500-1502/
Need a grinder with water/oil to keep the work cool.
Grind your profile and flatten the other end a little,
So when you put it in a vice and compress on a handle,
the round hole accepts the round/flat rod and holds tight.
Before that naturally is tempering... I'd get a 1/4" and cool
grind down the sides myself. Don't kneed to know heat treating.
Martin
On 5/12/2016 8:49 AM, Puckdropper wrote:
> I need an 1/8" chisel to clean up some cuts from a CNC machine, 1/8" in
> diameter. I've got mainly Stanley chisels and am reasonably happy with
> them, but my smallest is 1/4".
>
> Do you guys have any suggestions? Is the typical length of the 1/8" chisel
> going to be a problem trying to cut end grain? 1/8" would seem to be awful
> flexible...
>
> I was hoping to spend about $10, but a quick search on Amazon shows only
> one chisel for that price, a new Irwin Marples that is leaving many
> disappointed.
>
> Alternatively, I have some W1 drill rod and a mill... I guess I could make
> one but I've already got enough on my plate...
>
> Puckdropper
>
On 2016-05-12, [email protected] <[email protected]> wrote:
> Expensive, but they are out there.
>
> http://www.leevalley.com/en/wood/page.aspx?p=67689&cat=1,41504
Specially when buying one-at-a-time from Lee Valley. Try Amazon:
<http://www.amazon.com/Stanley-16-781-Sweetheart-Socket-Chisel/dp/B004TQGHOE/ref=sr_1_3?ie=UTF8&qid=1463063078&sr=8-3&keywords=Stanley+Sweetheart+Chisels>
....or....
http://tinyurl.com/haaoahb
That chisel will cost you $46, w/ shipping, from LV. Whatever Amazon
charges fer shipping, the total still hasta be less than $46. ;)
nb
On 2016-05-12, Scott Lurndal <[email protected]> wrote:
> Puckdropper <puckdropper(at)yahoo(dot)com> writes:
>>I was hoping to spend about $10......
> I have, and use, one of these:
>
> http://www.traditionalwoodworker.com/2mm-1_8-Bevel-Edge-Chisel-by-Two-Cherries/productinfo/500-1502/
This is closer to yer target expenditure and Narex has a very good
rep. Considered by many to be a "best buy":
<http://www.amazon.com/Narex-Woodworking-Cabinetmakers-Chisel-Handle/dp/B00V922QT6/ref=sr_1_2?ie=UTF8&qid=1463064904&sr=8-2&keywords=chisel+1%2F8>
....0r....
ttp://tinyurl.com/hwmvn33
Still gotta pay shipping, but shouldn't cost more than a few $$.
Definitely cheaper than the other recommended chisel. ;)
nb
On 5/12/2016 9:49 AM, Puckdropper wrote:
> I need an 1/8" chisel to clean up some cuts from a CNC machine, 1/8" in
> diameter. I've got mainly Stanley chisels and am reasonably happy with
> them, but my smallest is 1/4".
>
> Do you guys have any suggestions? Is the typical length of the 1/8" chisel
> going to be a problem trying to cut end grain? 1/8" would seem to be awful
> flexible...
>
> I was hoping to spend about $10, but a quick search on Amazon shows only
> one chisel for that price, a new Irwin Marples that is leaving many
> disappointed.
>
> Alternatively, I have some W1 drill rod and a mill... I guess I could make
> one but I've already got enough on my plate...
>
> Puckdropper
>
If you have a bench grinder, could you make a chisel out of an
appropriate sized screew driver?
Puckdropper wrote:
> I need an 1/8" chisel to clean up some cuts from a CNC machine, 1/8" in
> diameter. I've got mainly Stanley chisels and am reasonably happy with
> them, but my smallest is 1/4".
>
> Do you guys have any suggestions? Is the typical length of the 1/8" chisel
> going to be a problem trying to cut end grain? 1/8" would seem to be awful
> flexible...
>
> I was hoping to spend about $10,
If you are cutting hard wood, maybe it will let you down. Otherwise,
maybe it's worth $10 to find out, especially if the wood you are cutting
isn't too hard. You know going in that you may have to sharpen it a bit
more often. After all that, I hope you'll share your experience! : )
Bill
> but a quick search on Amazon shows only
> one chisel for that price, a new Irwin Marples that is leaving many
> disappointed.
>
> Alternatively, I have some W1 drill rod and a mill... I guess I could make
> one but I've already got enough on my plate...
>
> Puckdropper