I've been learning to make mortises the 'old-fashioned' way, by
chopping by hand.
The first few went pretty well, but the edge of my mortise chisel (Lie
Nielsen) will
need some work on the 220 stone to restore the edge. I'm certain that
my beginner
technique is much too hard on it.
The wood is Cherry, and the angle is 30 deg from the factory.
How many passes should I expect to make on a 1 inch deep mortise? I
suspect I
am driving the chisel too deep and damaging the edge during the chip
levering step.
Or perhaps I am making the chips too big.
Any advice out there from seasoned Neanders?
I think you should be able to get about 1/4 to 3/8 '' per hit. If the
edge does not surviive then try putting a microbevel of 5 deg. This
will keep the edge strong as well as allow you to reach deeper with the
original bevel angle.
On Dec 15, 8:28 pm, [email protected] wrote:
> I've been learning to make mortises the 'old-fashioned' way, by
> chopping by hand.
>
> The first few went pretty well, but the edge of my mortise chisel (Lie
> Nielsen) will
> need some work on the 220 stone to restore the edge. I'm certain that
> my beginner
> technique is much too hard on it.
>
> The wood is Cherry, and the angle is 30 deg from the factory.
>
> How many passes should I expect to make on a 1 inch deep mortise? I
> suspect I
> am driving the chisel too deep and damaging the edge during the chip
> levering step.
> Or perhaps I am making the chips too big.
>
> Any advice out there from seasoned Neanders?
alexy wrote:
> I in no way qualify as an "experienced neander", so take this FWIW.
> My technique is to start with a series of very small and shallow (not
> much deeper than the score lines that define the edge of the mortise)
> cuts to ease registration of the chisel in future passes. Then I take
> healthy chunks a little deeper than the amount taken along the length
> of the mortise--maybe a chip 3/8" deep but only 3/16" "long". But
> frankly I'm having a hard time visualizing it for description. It just
> "feels" right. Most of the levering I do is removing wood that has
> already been cut free or is just weakly attached along the long grain.
>
> Final cuts are several cuts on the last 1/4" of length to define the
> length of the mortise. These are paring or "mallet assisted paring"
> cuts looking more for clean surface than lots of stock removal.
> --
> Alex -- Replace "nospam" with "mail" to reply by email. Checked infrequently.
A 3/8 by 3/16 chip doesn't sound to much different than what I am
doing. Perhaps adding a 35 degree secondary bevel will help.
Vijay wrote:
> I think you should be able to get about 1/4 to 3/8 '' per hit. If the
> edge does not surviive then try putting a microbevel of 5 deg. This
> will keep the edge strong as well as allow you to reach deeper with the
> original bevel angle.
>
>
I'm going to add a 5 deg secondary bevel today and see how that works.
Lowell Holmes wrote:
>>
> Just my thoughts below and no more than that. :-)
>
> I was taught at Homestead Heritage you strike the chisels 3 times and then
> go to the next chip. If you take a chisel and present it to the wood, the
> chisel will go in as deep as it is going to with 3 strikes of the mallet. I
> don't really hammer it either, just good crisp blows.
>
> I define the mouth of the mortise with a series of small light chips,
> starting 1/8" from the starting end and stopping 1/8" from the end of the
> mortise.
>
> If you can get your hands on Frank Klausz's video "Mortise and Tenon
> Joinery", I think it will help.
>
> I have mortise chisels, but if I need a size mortise that I have no mortise
> chisel for, a bevel edge bench chisel does just fine. They don't use mortise
> chisels in the rocking chair classes at Homestead Heritage. They use blue
> handled Marples beveled edge chisels. The chairs will 45 -50 hand chopped
> mortises each.
>
> If your having a problem with the edges on your Lie Nielsen chisels, I
> suspect you are striking the chisels too hard. I have the beveled edge Lie
> Nielsen's, and they do just fine for mortises or dovetails.
I put the 'three strikes' rule in effect and the edge held up much
better. I think I might have tried to pry up too big a chip yesterday
and chipped an edge....
Lowell Holmes wrote:
> <[email protected]> wrote in message
> news:[email protected]...
> >>snip
> >
> > I put the 'three strikes' rule in effect and the edge held up much
> > better. I think I might have tried to pry up too big a chip yesterday
> > and chipped an edge....
>
>
>
> When prying the chips out, push towards the bevel on the chisel end. It will
> pop the chips loose with minimal movement of the handle. I start with the
> back of the chisel towards me and push away from me to pop the chips loose.
> If at the end of the mortise, you present the chisel to the work with the
> beveled edge vertical, strike the chisel, and then push the handle away the
> end chip will pop loose with not much movement and no damage to the edge.
>
> It sounds like you are on your way. :-)
Another clue! I probobly was prying the other way, and thats what
damaged the edge.
<[email protected]> wrote in message
news:[email protected]...
>
> I've been learning to make mortises the 'old-fashioned' way, by
> chopping by hand.
>
> The first few went pretty well, but the edge of my mortise chisel (Lie
> Nielsen) will
> need some work on the 220 stone to restore the edge. I'm certain that
> my beginner
> technique is much too hard on it.
>
> The wood is Cherry, and the angle is 30 deg from the factory.
>
> How many passes should I expect to make on a 1 inch deep mortise? I
> suspect I
> am driving the chisel too deep and damaging the edge during the chip
> levering step.
> Or perhaps I am making the chips too big.
>
> Any advice out there from seasoned Neanders?
What about a hand drill (bit and brace) to drill out the bulk of material in
the middle then use the chisel to square up and clean the edges?
--
Regards,
Dean Bielanowski
Editor, OnlineToolReviews.com
http://www.onlinetoolreviews.com
Over 110+ woodworking product reviews online!
-----------------------------------------------
Latest 6 Reviews:
- Nova Cole Jaws
- The Dust Picker!
- Leigh D1600 Dovetail Jig
- Wagner MMC220 Moisture Meter
- PowerTwist Link Belts
- Ryobi "LiveTool" Range
=========================
"Lowell Holmes" <[email protected]> wrote in message
news:56bhh.4097$od6.2666@trnddc04...
>
> > It sounds like you are on your way. :-)
>
Don't let the previous post confuse you. My thinking shifted from the
cutting edge of the chisel to the edge of the mortise.
The mortise cut shouldn't be hard work. Smaller and quicker blows will make
smaller chips with less effort will probably save time. The Klausz video
would help. He can chop a mortise in less time than it takes tell about it.
Taunton (Fine Woodworking) has the video.
You might want to view his video on dovetails on a drawer. He can dovetail a
complete drawer in just a few minutes.
<[email protected]> wrote in message
news:[email protected]...
>>snip
>
> I put the 'three strikes' rule in effect and the edge held up much
> better. I think I might have tried to pry up too big a chip yesterday
> and chipped an edge....
When prying the chips out, push towards the bevel on the chisel end. It will
pop the chips loose with minimal movement of the handle. I start with the
back of the chisel towards me and push away from me to pop the chips loose.
If at the end of the mortise, you present the chisel to the work with the
beveled edge vertical, strike the chisel, and then push the handle away the
end chip will pop loose with not much movement and no damage to the edge.
It sounds like you are on your way. :-)
<[email protected]> wrote in message
news:[email protected]...
>
> I've been learning to make mortises the 'old-fashioned' way, by
> chopping by hand.
>
> The first few went pretty well, but the edge of my mortise chisel (Lie
> Nielsen) will
> need some work on the 220 stone to restore the edge. I'm certain that
> my beginner
> technique is much too hard on it.
>
> The wood is Cherry, and the angle is 30 deg from the factory.
>
> How many passes should I expect to make on a 1 inch deep mortise? I
> suspect I
> am driving the chisel too deep and damaging the edge during the chip
> levering step.
> Or perhaps I am making the chips too big.
>
> Any advice out there from seasoned Neanders?
Just my thoughts below and no more than that. :-)
I was taught at Homestead Heritage you strike the chisels 3 times and then
go to the next chip. If you take a chisel and present it to the wood, the
chisel will go in as deep as it is going to with 3 strikes of the mallet. I
don't really hammer it either, just good crisp blows.
I define the mouth of the mortise with a series of small light chips,
starting 1/8" from the starting end and stopping 1/8" from the end of the
mortise.
If you can get your hands on Frank Klausz's video "Mortise and Tenon
Joinery", I think it will help.
I have mortise chisels, but if I need a size mortise that I have no mortise
chisel for, a bevel edge bench chisel does just fine. They don't use mortise
chisels in the rocking chair classes at Homestead Heritage. They use blue
handled Marples beveled edge chisels. The chairs will 45 -50 hand chopped
mortises each.
If your having a problem with the edges on your Lie Nielsen chisels, I
suspect you are striking the chisels too hard. I have the beveled edge Lie
Nielsen's, and they do just fine for mortises or dovetails.
Did you sharpen the chisel before you first used it?
<[email protected]> wrote in message
news:[email protected]...
>
> I've been learning to make mortises the 'old-fashioned' way, by
> chopping by hand.
>
> The first few went pretty well, but the edge of my mortise chisel (Lie
> Nielsen) will
> need some work on the 220 stone to restore the edge. I'm certain that
> my beginner
> technique is much too hard on it.
>
> The wood is Cherry, and the angle is 30 deg from the factory.
>
> How many passes should I expect to make on a 1 inch deep mortise? I
> suspect I
> am driving the chisel too deep and damaging the edge during the chip
> levering step.
> Or perhaps I am making the chips too big.
>
> Any advice out there from seasoned Neanders?
>
[email protected] wrote:
>
>I've been learning to make mortises the 'old-fashioned' way, by
>chopping by hand.
>
>The first few went pretty well, but the edge of my mortise chisel (Lie
>Nielsen) will
>need some work on the 220 stone to restore the edge. I'm certain that
>my beginner
>technique is much too hard on it.
>
>The wood is Cherry, and the angle is 30 deg from the factory.
>
>How many passes should I expect to make on a 1 inch deep mortise? I
>suspect I
>am driving the chisel too deep and damaging the edge during the chip
>levering step.
>Or perhaps I am making the chips too big.
>
>Any advice out there from seasoned Neanders?
I in no way qualify as an "experienced neander", so take this FWIW.
My technique is to start with a series of very small and shallow (not
much deeper than the score lines that define the edge of the mortise)
cuts to ease registration of the chisel in future passes. Then I take
healthy chunks a little deeper than the amount taken along the length
of the mortise--maybe a chip 3/8" deep but only 3/16" "long". But
frankly I'm having a hard time visualizing it for description. It just
"feels" right. Most of the levering I do is removing wood that has
already been cut free or is just weakly attached along the long grain.
Final cuts are several cuts on the last 1/4" of length to define the
length of the mortise. These are paring or "mallet assisted paring"
cuts looking more for clean surface than lots of stock removal.
--
Alex -- Replace "nospam" with "mail" to reply by email. Checked infrequently.