Hello,
I have inherited a Craftman Table saw from my Dad. I think I can
recollect that my Grandparents got it for him when I was a youngin'.
I just purchased a new belt for it, I don't think my Dad ever put a new
one on it. Anyway, in order to raise or lower the blade I have to loosen
a bolt on the motor pivot and then retighten when I have the blade
height set.
How is this suppose to work? I sure don't recall seeing any of the home
improvement shows or Norm adjusting this bolt when raising or lowering
the blade.
Thank you,
Fred
Frederick Wilson wrote:
> Hello,
>
> I have inherited a Craftman Table saw from my Dad. I think I can
> recollect that my Grandparents got it for him when I was a youngin'.
>
> I just purchased a new belt for it, I don't think my Dad ever put a new
> one on it. Anyway, in order to raise or lower the blade I have to loosen
> a bolt on the motor pivot and then retighten when I have the blade
> height set.
>
> How is this suppose to work? I sure don't recall seeing any of the home
> improvement shows or Norm adjusting this bolt when raising or lowering
> the blade.
>
> Thank you,
> Fred
The purpose of the bolt is to reduce vibration of
the saw. There is suppose to be a special washer
on the bolt that allows you to tighten to the
point the bolt doesn't vibrate loose but still
allows the part to slip. If you tighten it too
much, and don't loosen it when you raise the saw,
it will shear the bolt. That was the condition of
my dad's saw until I got the broken piece out.
Just put any washer on it next to the head,
tighten until vibration decrease with a running
saw but not much more than finger tight. Lift the
motor up by hand (or try) to assure that it will
move with only slight binding. (or keep a small
wrench handy to loosen and tighten it every time
you raise and lower the saw blade.
"Frederick Wilson" <[email protected]> wrote in message
news:[email protected]...
> Hello,
>
> I have inherited a Craftman Table saw from my Dad. I think I can recollect
> that my Grandparents got it for him when I was a youngin'.
>
> I just purchased a new belt for it, I don't think my Dad ever put a new
> one on it. Anyway, in order to raise or lower the blade I have to loosen a
> bolt on the motor pivot and then retighten when I have the blade height
> set.
>
> How is this suppose to work? I sure don't recall seeing any of the home
> improvement shows or Norm adjusting this bolt when raising or lowering the
> blade.
>
> Thank you,
> Fred
That bolt is not supposed to be that tight. Just snug enough to keep the
motor from "jumping".
It should be loose enough to allow for raising the blade.
Max D.
"Frederick Wilson" <[email protected]> wrote
> AHHHHHHHHHH, I get it. I know I have ran the saw with that bolt loose and
> the motor jumps around and the belt slaps around and the blade slips.
>
> I wonder what would happen if I put in a longer bolt with a tense spring
> under it.
>
> Thanks,
> Fred
There should be a tension washer under the bolt (when the saw was new).
A longer bolt and a spring sounds like a good idea.
Max D.
On Sun, 27 Mar 2005 09:49:23 -0500, Frederick Wilson
<[email protected]> wrote:
>AHHHHHHHHHH, I get it. I know I have ran the saw with that bolt loose
>and the motor jumps around and the belt slaps around and the blade slips.
>
>I wonder what would happen if I put in a longer bolt with a tense spring
>under it.
The design of a contractors saw is such that the weight of the motor
provides the sole tension on the belt. You can adjust the tension by
sizing the belt (or moving the motor) to vary the angle at which the
motor hangs on the mount (the Craftsman saw's motor mount is on two
rails which slide in and out of the trunnion assembly).
Somewhere out around 45° will give the maximum tension, but in
reality, you'll be better off with something less than that. I don't
have a magic number to tell you.
Because of that design, one is limited in what one may expect in
replacing the motor with one of higher power. There is only so much
power that can be transmitted with that system. 2 HP (REAL HP, not
Sears HP) or more is a waste of time.
--
LRod
Master Woodbutcher and seasoned termite
Shamelessly whoring my website since 1999
http://www.woodbutcher.net
Proud participant of rec.woodworking since February, 1997
AHHHHHHHHHH, I get it. I know I have ran the saw with that bolt loose
and the motor jumps around and the belt slaps around and the blade slips.
I wonder what would happen if I put in a longer bolt with a tense spring
under it.
Thanks,
Fred
Max wrote:
> "Frederick Wilson" <[email protected]> wrote in message
> news:[email protected]...
>
>>Hello,
>>
>>I have inherited a Craftman Table saw from my Dad. I think I can recollect
>>that my Grandparents got it for him when I was a youngin'.
>>
>>I just purchased a new belt for it, I don't think my Dad ever put a new
>>one on it. Anyway, in order to raise or lower the blade I have to loosen a
>>bolt on the motor pivot and then retighten when I have the blade height
>>set.
>>
>>How is this suppose to work? I sure don't recall seeing any of the home
>>improvement shows or Norm adjusting this bolt when raising or lowering the
>>blade.
>>
>>Thank you,
>>Fred
>
>
> That bolt is not supposed to be that tight. Just snug enough to keep the
> motor from "jumping".
> It should be loose enough to allow for raising the blade.
>
> Max D.
>
>