Ben,
IMO - it's a pretty good deal if the saws good shape. I think they go for
about $950 for the base model.
I've had one for about 3 years, used it heavily, and still like it. First
thing I did was put a WWII on it - I think that blade makes any saw work
better.
Good points:
1)Decent power on 120v
2)Runs pretty smooth.
3)Knee switch for shut-off
4)Fence moves easily and locks square
5)Minimal initial tuning required.
6)Table was dead flat
7) Retains tune-up well
8) Easy to read scale on fence
My complaints:
1) Sliding table (optional) was out of flat by almost .15" (not kidding).
Have to say though that the Dewalt service center replaced without question
even though I'd had it for over a year before I took it in.
2) Extension table (optional) began to sag shortly after installing a
router. Easily fixed with angle iron and shims though.
3) Sliding table mitre has too much flex. Replaced w/Incra mitre.
4) Dust colleciton is acceptable but could be better
5) Installation of 52" extension and sliding table was a bear (at least for
me)
If buying another hybrid I'd buy the Dewalt again just for the service
experience. I've been thinking of a PM66 (or the new PM - forget the model)
for my next saw though :^)
HTH
<[email protected]> wrote in message
news:[email protected]...
>I just bought a Dewalt DW746 w/mobile base from the Newspaper. It's
> about 2 years old, and in great shape. I paid $650 for it. I though
> this was pretty good, was I right?
>
> If you have one of these, do you like it?
>
> Thanks
> Ben
>
. But $650 isn't bad. So glad
>you didn't say you bought a Jet Stupid Saw, I mean, Super Saw.
>
>
Just Curious...since I have owned and used (heavily) a Jet Cabinet Saw
for the last 10-15 years....
Is the "Stupid: saw that bad... ? and basically why..?
Again just curious because I have absolutely no intentions of
replacing my saw... and to be honest if I did it would be another
Cabinet saw. .
Bob G..
Used one in a shop I worked at. It had the 50" fence and sliding table.
Power OK (1 3/4 hp @ 110V), fence surprisingly good for what it looked like,
loved the sliding table, hated the miter gauge contraption on the sliding
table (a square lived near the saw), and the dust collection sucked (not
literally). I think they paid something like $1100 for it. (pity, another
$600 and they would have had a 3hp Unisaw). But $650 isn't bad. So glad
you didn't say you bought a Jet Stupid Saw, I mean, Super Saw.
"eric" <[email protected]> wrote in message
news:1138203496.141878@sj-nntpcache-3...
> Ben,
>
> IMO - it's a pretty good deal if the saws good shape. I think they go for
> about $950 for the base model.
>
> I've had one for about 3 years, used it heavily, and still like it. First
> thing I did was put a WWII on it - I think that blade makes any saw work
> better.
>
> Good points:
> 1)Decent power on 120v
> 2)Runs pretty smooth.
> 3)Knee switch for shut-off
> 4)Fence moves easily and locks square
> 5)Minimal initial tuning required.
> 6)Table was dead flat
> 7) Retains tune-up well
> 8) Easy to read scale on fence
>
> My complaints:
> 1) Sliding table (optional) was out of flat by almost .15" (not kidding).
> Have to say though that the Dewalt service center replaced without
question
> even though I'd had it for over a year before I took it in.
> 2) Extension table (optional) began to sag shortly after installing a
> router. Easily fixed with angle iron and shims though.
> 3) Sliding table mitre has too much flex. Replaced w/Incra mitre.
> 4) Dust colleciton is acceptable but could be better
> 5) Installation of 52" extension and sliding table was a bear (at least
for
> me)
>
> If buying another hybrid I'd buy the Dewalt again just for the service
> experience. I've been thinking of a PM66 (or the new PM - forget the
model)
> for my next saw though :^)
>
> HTH
>
> <[email protected]> wrote in message
> news:[email protected]...
> >I just bought a Dewalt DW746 w/mobile base from the Newspaper. It's
> > about 2 years old, and in great shape. I paid $650 for it. I though
> > this was pretty good, was I right?
> >
> > If you have one of these, do you like it?
> >
> > Thanks
> > Ben
> >
>
>
<[email protected]> wrote in message
news:[email protected]...
> What's the benefit to wiring it for 220V? Can all induction motors be
> wired for 220V?
>
> Mike
>
The motor used to bog down while cutting thick hardwoods. No more. It also
starts instantly rather than start slow and spool up to speed. The motor
housing should state if it can be wired for 220V.
<[email protected]> wrote in message
news:[email protected]...
>I just bought a Dewalt DW746 w/mobile base from the Newspaper. It's
> about 2 years old, and in great shape. I paid $650 for it. I though
> this was pretty good, was I right?
>
> If you have one of these, do you like it?
>
> Thanks
> Ben
>
Got it - like it a lot. Did 2 things to make me love it:
1. Wired it for 220
2. Bought the sliding table
eric wrote:
> Ben,
>
> IMO - it's a pretty good deal if the saws good shape. I think they go for
> about $950 for the base model.
>
> I've had one for about 3 years, used it heavily, and still like it. First
> thing I did was put a WWII on it - I think that blade makes any saw work
> better.
>
> Good points:
> 1)Decent power on 120v
> 2)Runs pretty smooth.
> 3)Knee switch for shut-off
> 4)Fence moves easily and locks square
> 5)Minimal initial tuning required.
> 6)Table was dead flat
> 7) Retains tune-up well
> 8) Easy to read scale on fence
>
> My complaints:
> 1) Sliding table (optional) was out of flat by almost .15" (not kidding).
> Have to say though that the Dewalt service center replaced without question
> even though I'd had it for over a year before I took it in.
> 2) Extension table (optional) began to sag shortly after installing a
> router. Easily fixed with angle iron and shims though.
> 3) Sliding table mitre has too much flex. Replaced w/Incra mitre.
> 4) Dust colleciton is acceptable but could be better
> 5) Installation of 52" extension and sliding table was a bear (at least for
> me)
>
> If buying another hybrid I'd buy the Dewalt again just for the service
> experience. I've been thinking of a PM66 (or the new PM - forget the model)
> for my next saw though :^)
>
> HTH
>
> <[email protected]> wrote in message
> news:[email protected]...
>
>>I just bought a Dewalt DW746 w/mobile base from the Newspaper. It's
>>about 2 years old, and in great shape. I paid $650 for it. I though
>>this was pretty good, was I right?
>>
>>If you have one of these, do you like it?
>>
>>Thanks
>>Ben
>>
>
>
>
I agree with most of the above. I have the DW746, and have over time
added the sliding table (mine was flat), and the 52" rails. The table
mitre does have too much flex in it, but I've just lived with it.
Which Incra did you add?
Also, not as easy to fasten a jig to the fence as some others. But
overall, I really like it (with the WWII)
Eric