I just made a hand-power one. .750" plywood base about 16" x 16", .& 250"
plywood screwed to it, shy ~2" on either side. A precision 1.25"x.75" strip
screwd along top @ far edge from legs, and a strip on the underside for
clamping to a bench vice. Then a 3x3 drill pattern through both plys for a
mitre strip of .750" x 1.000" x ~13" long, attached with a wing nut into
bolt held in grooves cut in bottom of .750" ply. A std. planer (whole
thing, not-attached, arm operated) rides flat on the .750" ply, up against
the .250" ply, on either side. The far edge strip is at 90 degrees, but
also micro-adjustable with a flat bottomed hole, and lat bottoming screw in
oversized C'Bored hole.
BTW, why is my No.4 Stanley plane flat (i.e right angled via. plane blade
plane) on one side, but not on the other!?
----== Posted via Newsfeeds.Com - Unlimited-Unrestricted-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----
I put a couple of posts (bent) in "Newbie questions on use of table saw",
06/03/2006 6:39 PM you may want to see and also search group or net for term
"miter sled", or "mitre sled", as I was taught. "sled" or message or
subject "sled", & sender "bent". I know I described my mitXX sled, as well
as my cross-cut sled somewhere in here.
----== Posted via Newsfeeds.Com - Unlimited-Unrestricted-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----
Hi Patt,
Why not just cut your miters accurately on the table saw:
http://www.ts-aligner.com/accuratemiters.htm
Ed Bennett
[email protected]
http://www.ts-aligner.com
Patt wrote:
> I'm looking for the plans for a jig for fine tuning miter cuts after they
> have first been cut on the table saw. I saw,and can't remember where, a jig
> that used an iron from a plane. Does that sound familiar to anyone?
> Patt
OK, fine. I'll re-state it:
Why not just do it right the first time? Why start out planning for
failure? What if you could cut your miter on the table saw so that it
didn't need any "fine tuning" or "clean up" afterwards?
Ed Bennett
[email protected]
http://www.ts-aligner.com
Ed Bennett
Leon wrote:
> That might not help if "fine tuning miter cuts", means to clean up the
> miter cut.
Hi Leon,
Why do you think that the output of the TS will necessarily need
clean-up? Heck, a good quality sharp blade will produce excellent
results, free from tearout or any crushed fibers. And, it will cost
less than one of those guillotine things. Ever seen the Forrest demo
at the trade shows?
Again, why not just do it right the first time?
Ed Bennett
[email protected]
http://www.ts-aligner.com
Leon wrote:
> LOL.. No Ed what I mean is what if "fine tuning" is meant to reflect a more
> crisp edge with out tear out. What if the blade on the TS makes a perfect
> 45 but with lots of tear out and he wants to use some thing like those
> Guillotine jobs that cut a crisp sharp edge. No amount of machine set up
> is going to prevent a problems with a blade that causes a lot of tear out.
> You know, some people run their TS ripped edge through the jointer
> afterwards to clean up the cut.
<[email protected]> wrote in message
news:[email protected]...
> OK, fine. I'll re-state it:
>
> Why not just do it right the first time? Why start out planning for
> failure? What if you could cut your miter on the table saw so that it
> didn't need any "fine tuning" or "clean up" afterwards?
>
LOL.. No Ed what I mean is what if "fine tuning" is meant to reflect a more
crisp edge with out tear out. What if the blade on the TS makes a perfect
45 but with lots of tear out and he wants to use some thing like those
Guillotine jobs that cut a crisp sharp edge. No amount of machine set up
is going to prevent a problems with a blade that causes a lot of tear out.
You know, some people run their TS ripped edge through the jointer
afterwards to clean up the cut.
<[email protected]> wrote in message
news:[email protected]...
> Hi Patt,
>
> Why not just cut your miters accurately on the table saw:
>
> http://www.ts-aligner.com/accuratemiters.htm
>
> Ed Bennett
> [email protected]
> http://www.ts-aligner.com
That might not help if "fine tuning miter cuts", means to clean up the
miter cut.
In article <WNr9h.358303$5R2.189910@pd7urf3no>, "Patt" <[email protected]> wrote:
>I'm looking for the plans for a jig for fine tuning miter cuts after they
>have first been cut on the table saw. I saw,and can't remember where, a jig
>that used an iron from a plane. Does that sound familiar to anyone?
Perhaps you're referring to a shooting board? Google that, and see if that's
what you're looking for.
--
Regards,
Doug Miller (alphageek at milmac dot com)
It's time to throw all their damned tea in the harbor again.
Google = shooting board
On Fri, 24 Nov 2006 01:20:54 GMT, "Patt" <[email protected]> wrote:
>I'm looking for the plans for a jig for fine tuning miter cuts after they
>have first been cut on the table saw. I saw,and can't remember where, a jig
>that used an iron from a plane. Does that sound familiar to anyone?
>Patt
>
"Patt" <[email protected]> wrote in message
news:WNr9h.358303$5R2.189910@pd7urf3no...
> I'm looking for the plans for a jig for fine tuning miter cuts after they
> have first been cut on the table saw. I saw,and can't remember where, a
> jig
> that used an iron from a plane. Does that sound familiar to anyone?
> Patt
>
>
Consider that if your jig does not allow for you to PRECISELY cut your
pieces to an EXACT length, 45's for parallel pieces and picture frames will
probably have gaps at the joint.
As important as having an exact 45 or other degree cut, is having parallel
sides to be of exact equal length.
<[email protected]> wrote in message
news:[email protected]...
> Hi Leon,
>
> Why do you think that the output of the TS will necessarily need
> clean-up? Heck, a good quality sharp blade will produce excellent
> results, free from tearout or any crushed fibers. And, it will cost
> less than one of those guillotine things. Ever seen the Forrest demo
> at the trade shows?
>
> Again, why not just do it right the first time?
Maybe it was the comment by the OP that he was looking for a jig for fine
tuning miter cuts after they have first been cut on the table saw. That
really could mean anything, the comment was non specific.
IF he does not have a good blade the cuts can be cleaned up with a jig and a
plane blade. If his miter gauge is not reliably repeatable your tool will
come in handy.
Forrest demo's? I do my own Forrest demo most every day. ;~)
It is not a shooting board I'm looking for.
"Roy" <[email protected]> wrote in message
news:[email protected]...
> Google = shooting board
>
> On Fri, 24 Nov 2006 01:20:54 GMT, "Patt" <[email protected]> wrote:
>
> >I'm looking for the plans for a jig for fine tuning miter cuts after they
> >have first been cut on the table saw. I saw,and can't remember where, a
jig
> >that used an iron from a plane. Does that sound familiar to anyone?
> >Patt
> >
>