I was looking at spiral router bits on the internet and see they have two
flute up spiral bits and two flute down spiral bits. I'm confused. What
the heck is the difference between these two types and for what purpose. I
can imagine use for up spiral.. chips are extracted.. but down spiral?
Why.. Thanks..
Some background at the http://patwarner.com/faq.html no.12 link.
Great tools if you are prepared.
******************************************************************
Jim Hall wrote:
> I was looking at spiral router bits on the internet and see they have two
> flute up spiral bits and two flute down spiral bits. I'm confused. What
> the heck is the difference between these two types and for what purpose. I
> can imagine use for up spiral.. chips are extracted.. but down spiral?
> Why.. Thanks..
Interesting.. Thanks for cost saving tip..
"CW" <[email protected]> wrote in message
news:[email protected]...
> The idea behind down spiral is to reduce chipout on the surface.
> Particularly good for plywood. These spiral bits are direct copies of two
> flute metal cutting end mills. End mills are what I use. They are less
> expensive (about $25.00 to $30.00 dollars for a 1/2" end mill as opposed
to
> $50.00 to $60.00 for a spiral router bit) and work great. The only real
> advantage to the spiral router bit is shank size. They are ground to fit
the
> average router. The most common sizes in spiral router bits are 1/4, 3/8,
> and 1/2 and are ground to fit either a 1/4 or 1/2 collet. With end mills,
> about the only thing available to fit a 1/4 collet is a 1/4 cutter. 3/8
has
> a 3/8 shank. 1/2 is of course 1/2 shank. In between sizes have the next
size
> larger standard shank. Example: a 5/16 end mill will have a 3/8 shank.
Most
> routers have 1/4 and 1/2 collets. If there is a 3/8 collet available for
> your router (there is for PC routers), you have the size range covered
from
> 1/2 down. End mills are also available as up spiral or down spiral. Use
the
> down spiral only if neccessary. They tend to lift the router out of the
work
> and pack chips into the cut.
>
> "Jim Hall" <[email protected]> wrote in message
> news:yj7Lg.3357$TA5.2675@fed1read09...
> > I was looking at spiral router bits on the internet and see they have
two
> > flute up spiral bits and two flute down spiral bits. I'm confused.
What
> > the heck is the difference between these two types and for what purpose.
> I
> > can imagine use for up spiral.. chips are extracted.. but down spiral?
> > Why.. Thanks..
> >
> >
>
>
Got it..!! Thank you very much.. Now it makes sense..
"todd" <[email protected]> wrote in message
news:[email protected]...
> "Jim Hall" <[email protected]> wrote in message
> news:yj7Lg.3357$TA5.2675@fed1read09...
> >I was looking at spiral router bits on the internet and see they have two
> > flute up spiral bits and two flute down spiral bits. I'm confused.
What
> > the heck is the difference between these two types and for what purpose.
> > I
> > can imagine use for up spiral.. chips are extracted.. but down spiral?
> > Why.. Thanks..
>
> IIRC, the down spiral is used when cutting something like laminate where
you
> want to minimize chipping.
>
> todd
>
>
"Jim Hall" <[email protected]> wrote in message
news:yj7Lg.3357$TA5.2675@fed1read09...
>I was looking at spiral router bits on the internet and see they have two
> flute up spiral bits and two flute down spiral bits. I'm confused. What
> the heck is the difference between these two types and for what purpose.
> I
> can imagine use for up spiral.. chips are extracted.. but down spiral?
> Why.. Thanks..
IIRC, the down spiral is used when cutting something like laminate where you
want to minimize chipping.
todd
"todd" <[email protected]> wrote in message
>
> IIRC, the down spiral is used when cutting something like laminate where
> you want to minimize chipping.
>
Keep in mid that if the router is mounted in a table, the down spiral is now
an up spiral when looking at it so plan your cuts accordingly. Up spiral
bits will help remove material better when cutting a groove too.
The idea behind down spiral is to reduce chipout on the surface.
Particularly good for plywood. These spiral bits are direct copies of two
flute metal cutting end mills. End mills are what I use. They are less
expensive (about $25.00 to $30.00 dollars for a 1/2" end mill as opposed to
$50.00 to $60.00 for a spiral router bit) and work great. The only real
advantage to the spiral router bit is shank size. They are ground to fit the
average router. The most common sizes in spiral router bits are 1/4, 3/8,
and 1/2 and are ground to fit either a 1/4 or 1/2 collet. With end mills,
about the only thing available to fit a 1/4 collet is a 1/4 cutter. 3/8 has
a 3/8 shank. 1/2 is of course 1/2 shank. In between sizes have the next size
larger standard shank. Example: a 5/16 end mill will have a 3/8 shank. Most
routers have 1/4 and 1/2 collets. If there is a 3/8 collet available for
your router (there is for PC routers), you have the size range covered from
1/2 down. End mills are also available as up spiral or down spiral. Use the
down spiral only if neccessary. They tend to lift the router out of the work
and pack chips into the cut.
"Jim Hall" <[email protected]> wrote in message
news:yj7Lg.3357$TA5.2675@fed1read09...
> I was looking at spiral router bits on the internet and see they have two
> flute up spiral bits and two flute down spiral bits. I'm confused. What
> the heck is the difference between these two types and for what purpose.
I
> can imagine use for up spiral.. chips are extracted.. but down spiral?
> Why.. Thanks..
>
>