I am taking on a project that is bigger than I have done before. An 8
foot entertainment wall unit in 2', 4', 2' sections. I have built the
carcases but I am stuck on the doors. How do I predict the size I need
for the face frame cup hinges? Is there a difference in overlay when the
door is closed and when it is open and if so which overlay size to you
buy for?. I have visited Rockler's web site but the info is still
sketchy to me.
Thanks for any help
kb
"Leon" wrote in message
> I have probably drilled a thousand 1-3/8" holes in doors and always used
the
> drill press with a temp fence. I draw a line at the center location of 1
> hole and drill the hole. Then I extend that line to the fence. After that
> simply align the line on the door to the one on the fence. I used to use
> stops but find a tape measure and a quick mark on the door works just
fine.
Great minds think alike ... I first used stops also, but your method and/or
pencil lines on the fence in place of stops (that way I don't have to mark
each door) works fine too, particularly with overlay doors on FF cabinets
where the top and bottom hinge alignment distance is not all that critical.
--
www.e-woodshop.net
Last update: 11/06/05
"Keith Boeheim" <[email protected]> wrote in message
news:[email protected]...
>I am taking on a project that is bigger than I have done before. An 8 foot
>entertainment wall unit in 2', 4', 2' sections. I have built the carcases
>but I am stuck on the doors. How do I predict the size I need for the face
>frame cup hinges? Is there a difference in overlay when the door is closed
>and when it is open and if so which overlay size to you buy for?. I have
>visited Rockler's web site but the info is still sketchy to me.
>
> Thanks for any help
I buy these type hinges by the 100's. Typically the face frame overlay
hinges come in different overlay measurements. I always use 1/2" overlay
hinges. Simply double the amount of overlay and add it to the width and
height of the actual opening in the cabinet. For example when I use 1/2"
overlay face frame hinges on a door to cover a 14" x 20" opening, I make the
door 15"x21".
The second obstacle is hole placement in the door for the cup. Every hinge
of this type that I have used requires that you have the edge of the hole
1/8" from the edge of the door. Up and down measurements are strictly up to
you. If you drill the hole more than 1/8" from the edge of the door the
door will rub the cabinet face frame when you open or close the door.
Theoretically doors using these type hinges can almost be places next to
each other so clearance is normally not an issue providing you measure
properly. The hinges offset them selves when opened and closed such that
tight tolerances between doors can be obtained. That said this is more
important when building the more traditional Euro cabinets that have no face
frames at all and all you see is doors and drawer fronts. Typically with a
face framed cabinet you have plenty of clearance as usually the face frame
is exposed between the doors.
"Swingman" <[email protected]> wrote in message
news:[email protected]...
> All good info ... about the only thing I could add for the OP with regard
> to
> the "pricey jigs" is that if he has a drill press, all he really needs to
> locate the 35mm holes precisely/properly in the doors is a simple fence
> clamped solidly to the drill press table ... those "pricey jigs" are
> mainly
> for those operating only with a hand drill, IME.
>
I've found the Rockler jigs to locate the cabinet side of the hinge to be
quite handy.
"Leon" <[email protected]> wrote in message
news:[email protected]...
I guess the pivot point on the different sized 38's is in
> different places in the cup.
Oops.. that should have been,
I guess the pivot point on the different sized 33's is in
> different places in the cup.
"Swingman" <[email protected]> wrote in message
news:[email protected]...
>
> All good info ... about the only thing I could add for the OP with regard
> to
> the "pricey jigs" is that if he has a drill press, all he really needs to
> locate the 35mm holes precisely/properly in the doors is a simple fence
> clamped solidly to the drill press table ... those "pricey jigs" are
> mainly
> for those operating only with a hand drill, IME.
I have probably drilled a thousand 1-3/8" holes in doors and always used the
drill press with a temp fence. I draw a line at the center location of 1
hole and drill the hole. Then I extend that line to the fence. After that
simply align the line on the door to the one on the fence. I used to use
stops but find a tape measure and a quick mark on the door works just fine.
"Swingman" <[email protected]> wrote in message
news:[email protected]...
> "BobS" wrote in message
>> According to Blum and the hinges I usually get (compact 33's) there is a
>> difference for each overlay. The distance from the edge of the door to
> the
>> edge of the cup hole varies from 1/8" to 5/16"
> .
>
> Yep ... my last blum spec sheet for _inset_ cabinet doors on non-FF
> cabinets called for 3/16". I don't recall which model blum it was, but the
> blums I used with the accuride flipper slides on the same project called
> for
> 3/16" also.
>
> The blums I use on 3/8" overlay doors for FF cabinets generally call for
> Leon's 1/8", though.
I use the Compact 38's. I have almost always used the face frame stile as
the OP indicated. I absolutely do no doubt that the non-FF hinges require
different spacing from the edge of the door.
Leon,
According to Blum and the hinges I usually get (compact 33's) there is a
difference for each overlay. The distance from the edge of the door to the
edge of the cup hole varies from 1/8" to 5/16"
(http://www.blum.com/usa/img/brochure_pdf/1046_Concealed_hinges.pdf ) see
table on page 3.
I know that's not much but it can ruin your whole day if you misdrilll the
cup holes. I haven't checked all their hinges but I thought they had a new
one out where you could use a -set- offset (as in production run) and adjust
for different overlay's on the arm. Don't recall where I read that - and
maybe it wasn't for a Blum hinge.
Bob S.
"Leon" <[email protected]> wrote in message
news:72ucf.14026$q%[email protected]...
> door 15"x21".
> The second obstacle is hole placement in the door for the cup. Every
> hinge of this type that I have used requires that you have the edge of the
> hole 1/8" from the edge of the door. Up and down measurements are
> strictly up to you. If you drill the hole more than 1/8" from the edge of
> the door the door will rub the cabinet face frame when you open or close
> the door.
"BobS" <[email protected]> wrote in message
news:[email protected]...
> No doubt about it - they show 1/8" for the Compact 38 hinges. Now go look
> at the Compact 33 on that site and look at the Application Guide and you
> tell me what the offset would be? They sure make that chart hard to
> understand.....
Yeah I read it. I had always assumed the 1/8" was so that the door edge
would clear the face frame since the hinge holds the door out from the face
frame 1/8". I guess the pivot point on the different sized 38's is in
different places in the cup.
> Guess the point here is - best read the instructions for the hinge you're
> using before applying power.....
16 years ago I used some Blum hinges that actually mounted on the surface of
the face frame. Those were a real PIA to properly position on the cabinet.
Still even back then the spacing was 1/8" I agree though it is safe to read
the directions especially when using a new style hinge.
Keith,
Not sure I'm understanding what you wrote but it sounds like you want to
know what kind of Euro (hidden hinge) to buy. You can look up the exact
sizes up at several sites ( www.blum.com ) is one.
As for how much overlay (door larger than opening), that's a design decision
but 1/2" overlay is pretty typical. For instance, if the cabinet door is
made 1" wider and 1" taller than the face frame openings then you would have
1/2" overlay all the way around and would use a 1/2" overlay hinge. The
next consideration is how far do you want the hinge to open the door (90°,
110°... more...) and then whether the hinge is mounted to the edge of the
face frame (3/4" stock I presume) or is it a side mounted hinge as used in
Euro stile cabinets that don't have a face frame.
And.... if you're design includes a center stile (a door on either side)
then you need to consider the width of the stile, how much the doors will
overlap the center stile (looks count here...) The overlay on the hinge
side can be different than the handle side. For that matter, you can have
whatever overlay you want on all the edges just so long as the hinge side is
an overlay size that matches the type hinge you're buying.
Then there is the 35mm hole for the hinge cup on the door itself but there
are styles that mount flush and do not need a hole if I remember correctly.
Alignment is pretty critical and there are some pricey jigs you can buy to
guide the cutting of the hole and mounting screws but you can make one in
about 10 mins from some scraps too. The distance from the edge of the door
to the hole is 1/8" on 1/2" overlay doors. If you use 3/8" or 5/8" overlay
hinges then that distance to edge and hole will vary. So yes, you need to
know how much the door will overlay the hinge side of the frame before you
purchase the hinges.
But there are always exceptions and like just about all other technologies -
they change damn near overnight.
Bob S.
"Keith Boeheim" <[email protected]> wrote in message
news:[email protected]...
>I am taking on a project that is bigger than I have done before. An 8 foot
>entertainment wall unit in 2', 4', 2' sections. I have built the carcases
>but I am stuck on the doors. How do I predict the size I need for the face
>frame cup hinges? Is there a difference in overlay when the door is closed
>and when it is open and if so which overlay size to you buy for?. I have
>visited Rockler's web site but the info is still sketchy to me.
>
> Thanks for any help
>
> kb
In article <[email protected]>,
"Swingman" <[email protected]> wrote:
> those "pricey jigs" are mainly
> for those operating only with a hand drill, IME.
By hand, eh? Not me. If there needs to be just one reason to buy a drill
press...........
It is not easy to drill within a few millimetres from the face of the
door with a bit that big and keep the bottom of the hole parallel to the
face of the door at the same time...... all without a depth-stop *S*
YIKES!!
I did make a small guide/jig that clamps onto the door and with a 1/2"
mortising router bit and a bushing, it makes nice flat-bottomed
hinge-cup holes. Strictly for that 'field emergency'.
"BobS" wrote in message
> Then there is the 35mm hole for the hinge cup on the door itself but there
> are styles that mount flush and do not need a hole if I remember
correctly.
> Alignment is pretty critical and there are some pricey jigs you can buy to
> guide the cutting of the hole and mounting screws but you can make one in
> about 10 mins from some scraps too. The distance from the edge of the door
> to the hole is 1/8" on 1/2" overlay doors. If you use 3/8" or 5/8"
overlay
> hinges then that distance to edge and hole will vary. So yes, you need to
> know how much the door will overlay the hinge side of the frame before you
> purchase the hinges.
All good info ... about the only thing I could add for the OP with regard to
the "pricey jigs" is that if he has a drill press, all he really needs to
locate the 35mm holes precisely/properly in the doors is a simple fence
clamped solidly to the drill press table ... those "pricey jigs" are mainly
for those operating only with a hand drill, IME.
--
www.e-woodshop.net
Last update: 11/06/05
"BobS" wrote in message
> According to Blum and the hinges I usually get (compact 33's) there is a
> difference for each overlay. The distance from the edge of the door to
the
> edge of the cup hole varies from 1/8" to 5/16"
.
Yep ... my last blum spec sheet for _inset_ cabinet doors on non-FF
cabinets called for 3/16". I don't recall which model blum it was, but the
blums I used with the accuride flipper slides on the same project called for
3/16" also.
The blums I use on 3/8" overlay doors for FF cabinets generally call for
Leon's 1/8", though.
--
www.e-woodshop.net
Last update: 11/06/05
cup hinges(euro hinges) come in three "basic" flavors with
a little twist here and there.
(1) full overlay
(2) half overlay (used when two doors are back to back)
(3) full inset
(4) face frame --- full overlay
A cheap and easy way to predict door size is make a "dummy"
out of 3/4" mdf and see how it works.
With face frame hinges, I would shoot for 3/8" all the way
around BUT ..you need to pick a hinge before you build the
doors. The hinge will determine door size.
Did you read this ????
http://www.rockler.com/articles/display_article.cfm?&story_id=51#overlay
Note that they come in 3 different overlays....
I would find a hinge I like and stick with that hinge going forward.
Keith Boeheim wrote:
> I am taking on a project that is bigger than I have done before. An 8
> foot entertainment wall unit in 2', 4', 2' sections. I have built the
> carcases but I am stuck on the doors. How do I predict the size I need
> for the face frame cup hinges? Is there a difference in overlay when the
> door is closed and when it is open and if so which overlay size to you
> buy for?. I have visited Rockler's web site but the info is still
> sketchy to me.
>
> Thanks for any help
>
> kb
I forgot:
http://www.hardwaresource.com/newsdetail.asp?ID=12
which describes it fairly well...
Keith Boeheim wrote:
> I am taking on a project that is bigger than I have done before. An 8
> foot entertainment wall unit in 2', 4', 2' sections. I have built the
> carcases but I am stuck on the doors. How do I predict the size I need
> for the face frame cup hinges? Is there a difference in overlay when the
> door is closed and when it is open and if so which overlay size to you
> buy for?. I have visited Rockler's web site but the info is still
> sketchy to me.
>
> Thanks for any help
>
> kb
"BobS" <[email protected]> wrote in message
news:[email protected]...
>
> I know that's not much but it can ruin your whole day if you misdrilll the
> cup holes. I haven't checked all their hinges but I thought they had a
> new one out where you could use a -set- offset (as in production run) and
> adjust for different overlay's on the arm. Don't recall where I read
> that - and maybe it wasn't for a Blum hinge.
>
> Bob S.
Thanks for pointing that out to me Bob. Personally I use the Blum Compact
38. This is a 1 piece design and according to the application guide the
offset is 1/8" on all overlays.
Take a look here and if you click the application icon it appears to be a
1/8" off set that I assume is for all overlays. Again I have always only
used 1/2" overlays.
http://wwhardware.com/catalog.cfm/GroupID/Cabinet%20Hinges/CatID/Cabinet%20Hinges%2C%20Blum%26%23174%3B%20Concealed/SubCatID/105%26%230176%3B%20Compact%2038
No doubt about it - they show 1/8" for the Compact 38 hinges. Now go look
at the Compact 33 on that site and look at the Application Guide and you
tell me what the offset would be? They sure make that chart hard to
understand.....
Guess the point here is - best read the instructions for the hinge you're
using before applying power.....
Bob S.
"Leon" <[email protected]> wrote in message
news:[email protected]...
>
> "BobS" <[email protected]> wrote in message
> news:[email protected]...
>>
>> I know that's not much but it can ruin your whole day if you misdrilll
>> the cup holes. I haven't checked all their hinges but I thought they had
>> a new one out where you could use a -set- offset (as in production run)
>> and adjust for different overlay's on the arm. Don't recall where I read
>> that - and maybe it wasn't for a Blum hinge.
>>
>> Bob S.
>
> Thanks for pointing that out to me Bob. Personally I use the Blum Compact
> 38. This is a 1 piece design and according to the application guide the
> offset is 1/8" on all overlays.
> Take a look here and if you click the application icon it appears to be a
> 1/8" off set that I assume is for all overlays. Again I have always only
> used 1/2" overlays.
>
>
> http://wwhardware.com/catalog.cfm/GroupID/Cabinet%20Hinges/CatID/Cabinet%20Hinges%2C%20Blum%26%23174%3B%20Concealed/SubCatID/105%26%230176%3B%20Compact%2038
>