Bandsaw/Drill Press Tables?

> Is there some reason not to remove the existing table and mount the new
> one
> directly to the trunions?

Way too difficult and no real benefit. I have a 30" x 18" table that is
held in place with two handscrews and I can have it off in about 1 minute.
Actually, I cannot think of a reason I would take it off. I built mine with
extendable table, extendable fence, tracks, etc. It can be used equally
well for wood or metal projects. The tracks are spaced to accept a the
hold-down vices I use for occasional metalworking.

As far as clearance loss goes I guess it depends on whether you have a floor
or bench model. I used two thicknesses of 3/4" Baltic Birch ply on mine,
with a third ply at the ends. Mine is a floor model so clearance is no
issue.

However, weight might be an issue if you don't have a mechanical lift (rack
and crank, etc,). Mine was a little heavy before the auxiliary table. I
rigged up a simple and inexpensive counter weight using cable, pulleys and
rubber bungee. Works fine. I posted pics a few months ago.

Building a drill press table is a fun and useful project. Depending on
design, it can add a lot of utility to the tool.

RonB

I built a pretty hefty add-on drill press table and it is heavy.
http://www.anneldavis.com/bobandanne/drillpresstable.htm.

The weight doesn't really bother me, but the lack of clearance to get
to the crank to raise and lower it does. I'm going to modify the table
to give me more clearance back there.

I don't have the tools to make a table that would fit in the existing
trunion accurately and don't really see any advantage to replacing it.
Bob

> Ron, saw your setup when you posted it. Very ingenous.
>
> Thanks to everyone for their comments on the drill press table. Anyone
> got any comments on the band saw?

Thanks - Probably more stingy than ingenious. Actully the guys who frequent
this group came up with most of it.

Yeah, I addressed the drill press more than band saw. You are giving up
some depth clearance on that tool. I believe I saw some auxilary band saw
table and accessory projects in one of the magazines during the past 1 to 2
years. The table I am thinking of sat on top of the existing cast table.
Best bet is WOOD magazine but I loaned several of mine to my son a while
back. You might check the project list on their site.

RonB

"Lobby Dosser" <[email protected]> wrote in message
news:wUDid.3462$xO1.1057@trnddc08...
> I've been looking at commercial add on tables for bandsaws and drill
> presses with a view to building my own. All the models I have seen so far
> are literaly 'add ons'; the new table is mounted directly over the
existing
> table. The same seems to hold true for plans in magazines. It seems to me
> that this adds weight and decreases clearance.
>
> Is there some reason not to remove the existing table and mount the new
one
> directly to the trunions?
>
> TIA
>
> LD

I'd say the reason would be primarily one of flexibility. A lot of people
use their drill presses for multiple tasks - some woodworking, some metal
working, some respectfully use the table as it was originally intended - as
yet another flat surface in the shop for the convenient placement of
anything that you need to put down. Point being - I would not want to do
metal work on a nice wood top - metal work often gets messy. Better to do
it on the original table and throw on a top that is somewhat special purpose
when I need to do something like drill mortises with the press. Everything
stays much cleaner - the wood does not stand the chance of picking up oil
that you might not have cleaned up well enough from the last metal work you
did.

Also - as time goes by you'll likely build more than one special purpose top
for your press to accommodate different tasks. It's easier to unclamp one
from a table and clamp another one on than it is to remove a table and mount
it.

--

-Mike-
[email protected]

I just installed an "add-on". I see zero reason to remove the original
table. It would take more time, I don't need the clearance, and it's
something else to store. It works fine by just attaching the new table
to the old.

David

Lobby Dosser wrote:

> I've been looking at commercial add on tables for bandsaws and drill
> presses with a view to building my own. All the models I have seen so far
> are literaly 'add ons'; the new table is mounted directly over the existing
> table. The same seems to hold true for plans in magazines. It seems to me
> that this adds weight and decreases clearance.
>
> Is there some reason not to remove the existing table and mount the new one
> directly to the trunions?
>
> TIA
>
> LD

"Lobby Dosser" <[email protected]> wrote in message
> The same seems to hold true for plans in magazines. It seems to me
> that this adds weight and decreases clearance.
>
> Is there some reason not to remove the existing table and mount the new
> one
> directly to the trunions?

As for adding weight, less than three pounds. Clearance lost is 3/4". I've
never use the full depth on my DP so I did not care.

To remove the table I just remove two wing nuts, about 20 seconds each.

"RonB" <[email protected]> wrote:

>> Is there some reason not to remove the existing table and mount the
>> new one
>> directly to the trunions?
>
> Way too difficult and no real benefit. I have a 30" x 18" table that
> is held in place with two handscrews and I can have it off in about 1
> minute. Actually, I cannot think of a reason I would take it off. I
> built mine with extendable table, extendable fence, tracks, etc. It
> can be used equally well for wood or metal projects. The tracks are
> spaced to accept a the hold-down vices I use for occasional
> metalworking.
>
> As far as clearance loss goes I guess it depends on whether you have a
> floor or bench model. I used two thicknesses of 3/4" Baltic Birch ply
> on mine, with a third ply at the ends. Mine is a floor model so
> clearance is no issue.
>
> However, weight might be an issue if you don't have a mechanical lift
> (rack and crank, etc,). Mine was a little heavy before the auxiliary
> table. I rigged up a simple and inexpensive counter weight using
> cable, pulleys and rubber bungee. Works fine. I posted pics a few
> months ago.
>
> Building a drill press table is a fun and useful project. Depending
> on design, it can add a lot of utility to the tool.
>
> RonB
>
>

Ron, saw your setup when you posted it. Very ingenous.

Thanks to everyone for their comments on the drill press table. Anyone
got any comments on the band saw?