Mostly a lurker here but desperately need your help on these doors.
These are nothing fancy floating panel doors to go on a painted storage
cabinet. When I dry fit the frames everything is flat and square on the
workbench and everything lines up. The panels when laid on the bench
are flat also. When I slide the panels into the frames for the final
dry fit, one corner or opposing corners will slightly bow. Have checked
all rails and stiles for squareness of cuts, groove for correct depth
and that the panel grooves line up. What am I missing? Any thoughts
and assistance will be greatly appreciated.
=A0Have checked
> all rails and stiles for squareness of cuts, groove for correct depth
> and that the panel grooves line up. =A0
Check that the style/rail grooves are cut straight, all along their
run, no slight curves WITHIN those channels. Also, check that the
panel edges are cut straight all along their run.
The channel ends may line up, but there may be a "bend" (curved cut,
somehow) in a center area, somewhere. Same with the style/rail
channels.... the ends may align, but an edge may have a curved cut
(somehow), somewhere. The boards may be flat... it may be a cut that
is not straight.
Flip the panel over, right-left & up-down, install each application.
Does the problem still exist in each application?
Sonny
Sonny likely identified the issue. If a straight edge laid up against
the groove shows some bow, you can just rabbit the back side of the
panel(s) a bit to add clearance and overcome the binding. Then use
some space balls or some other method like foam rubber or tubing, etc
added in the bottom of the grooves to keep the panels from rattling.
Sounds like you are doing some cool stuff and doing it right ie Dry
Fitting. Not everyone is alwasy so smart and ends up witha glued up
problem. Of course that has "never" happened to me. ;^)
On May 12, 7:51=A0am, Roger <[email protected]> wrote:
> Mostly a lurker here but desperately need your help on these doors.
> These are nothing fancy floating panel doors to go on a painted storage
> cabinet. =A0When I dry fit the frames everything is flat and square on th=
e
> workbench and everything lines up. =A0The panels when laid on the bench
> are flat also. =A0When I slide the panels into the frames for the final
> dry fit, one corner or opposing corners will slightly bow. =A0Have checke=
d
> all rails and stiles for squareness of cuts, groove for correct depth
> and that the panel grooves line up. =A0What am I missing? =A0Any thoughts
> and assistance will be greatly appreciated.
On 5/12/2011 11:12 AM, Sonny wrote:
> Have checked
>> all rails and stiles for squareness of cuts, groove for correct depth
>> and that the panel grooves line up.
>
> Check that the style/rail grooves are cut straight, all along their
> run, no slight curves WITHIN those channels. Also, check that the
> panel edges are cut straight all along their run.
>
> The channel ends may line up, but there may be a "bend" (curved cut,
> somehow) in a center area, somewhere. Same with the style/rail
> channels.... the ends may align, but an edge may have a curved cut
> (somehow), somewhere. The boards may be flat... it may be a cut that
> is not straight.
>
> Flip the panel over, right-left& up-down, install each application.
> Does the problem still exist in each application?
>
> Sonny
Thanks for the ideas and quick response. Will recheck everything again
but had not thought about the grooves not being cut perfectly straight.
Will check that first I think.
Roger
On 5/12/2011 1:13 PM, SonomaProducts.com wrote:
> Sonny likely identified the issue. If a straight edge laid up against
> the groove shows some bow, you can just rabbit the back side of the
> panel(s) a bit to add clearance and overcome the binding. Then use
> some space balls or some other method like foam rubber or tubing, etc
> added in the bottom of the grooves to keep the panels from rattling.
>
> Sounds like you are doing some cool stuff and doing it right ie Dry
> Fitting. Not everyone is alwasy so smart and ends up witha glued up
> problem. Of course that has "never" happened to me. ;^)
>
>
> On May 12, 7:51 am, Roger<[email protected]> wrote:
>> Mostly a lurker here but desperately need your help on these doors.
>> These are nothing fancy floating panel doors to go on a painted storage
>> cabinet. When I dry fit the frames everything is flat and square on the
>> workbench and everything lines up. The panels when laid on the bench
>> are flat also. When I slide the panels into the frames for the final
>> dry fit, one corner or opposing corners will slightly bow. Have checked
>> all rails and stiles for squareness of cuts, groove for correct depth
>> and that the panel grooves line up. What am I missing? Any thoughts
>> and assistance will be greatly appreciated.
>
Thanks to you and Sonny. You both nailed it. Really close inspection
revealed about a 2 inch long groove section that was not perfectly
straight. Recut the groove on that section and then it was time for a
few cold ones to restore my sanity. Thanks again!!
Not ever having created a raised panel door or any rail and style doors,
yet, I would have thought the panels should fit very loosely and then after
fitting and maintaining flat a rubberized (usually silicone clear) caulking
would be applied, inside to stop rattling and assure expansion adaption. I
have seen too many that rattle like heck after ten years of hanging in a dry
heated home.
Is this too tacky for better quality cabinets? I know this may not help the
rail and styles already machined out.
---------------
"SonomaProducts.com" wrote in message
news:cfaf04b1-b16c-4ad0-9f77-4d26baf282fd@s16g2000prf.googlegroups.com...
Sonny likely identified the issue. If a straight edge laid up against
the groove shows some bow, you can just rabbit the back side of the
panel(s) a bit to add clearance and overcome the binding. Then use
some space balls or some other method like foam rubber or tubing, etc
added in the bottom of the grooves to keep the panels from rattling.
Sounds like you are doing some cool stuff and doing it right ie Dry
Fitting. Not everyone is alwasy so smart and ends up witha glued up
problem. Of course that has "never" happened to me. ;^)
On May 12, 7:51 am, Roger <[email protected]> wrote:
Mostly a lurker here but desperately need your help on these doors.
These are nothing fancy floating panel doors to go on a painted storage
cabinet. When I dry fit the frames everything is flat and square on the
workbench and everything lines up. The panels when laid on the bench
are flat also. When I slide the panels into the frames for the final
dry fit, one corner or opposing corners will slightly bow. Have checked
all rails and stiles for squareness of cuts, groove for correct depth
and that the panel grooves line up. What am I missing? Any thoughts
and assistance will be greatly appreciated.