I've got a radius plane on order, this one:
http://www.rockler.com/product.cfm?page=5320
It's supposed to round over corners with a 1/16" radius. This brings
up another probably silly question. Do I sand the flat sides of the
(oak 1x2) wood first, then apply the radius plane? Will I then need to
sand (gently, I suppose) the radius edge? Or do apply the plane to the
unsanded wood, then sand the whole thing? Or do the coarse sanding
first, or... what?
Greg Guarino
Andy Dingley wrote:
> On Mon, 24 Apr 2006 22:59:11 GMT, Greg Guarino <[email protected]>
> wrote:
>
> >I've got a radius plane on order, this one:
> >http://www.rockler.com/product.cfm?page=5320
>
> Can you cancel? Those things are a _real_ dog.
I wasn't going to rain on the parade, but since it's already started
drizzling...
I have the same radius plane and I never use it. I find the can opener
style corner edging tools much easier and faster to use. Since the
tool can cut on the push or pull, you don't have to reverse the tool if
the grain changes.
http://www.leevalley.com/wood/page.aspx?c=2&p=32682&cat=1,42524
Another benefit is that it cuts much closer into corners. The small
distance from the corner is uniform, of course, and it makes a fast way
to cut a lambs tongue.
R
Greg Guarino wrote:
> I've got a radius plane on order, this one:
>
> http://www.rockler.com/product.cfm?page=5320
>
> It's supposed to round over corners with a 1/16" radius. This brings
> up another probably silly question. Do I sand the flat sides of the
> (oak 1x2) wood first, then apply the radius plane? Will I then need to
> sand (gently, I suppose) the radius edge? Or do apply the plane to the
> unsanded wood, then sand the whole thing? Or do the coarse sanding
> first, or... what?
>
Sanding leaves grit in the wood that is not kind to the sharp
edges of tools. So whenever possible, leave sanding until
after all the cutting, planing, and scraping is done.
--
FF
In article <[email protected]>, Greg Guarino
<[email protected]> wrote:
> It's supposed to round over corners with a 1/16" radius. This brings
> up another probably silly question. Do I sand the flat sides of the
> (oak 1x2) wood first, then apply the radius plane? Will I then need to
> sand (gently, I suppose) the radius edge? Or do apply the plane to the
> unsanded wood, then sand the whole thing? Or do the coarse sanding
> first, or... what?
Sand last.
On Mon, 24 Apr 2006 22:59:11 GMT, Greg Guarino <[email protected]>
wrote:
>I've got a radius plane on order, this one:
>http://www.rockler.com/product.cfm?page=5320
Can you cancel? Those things are a _real_ dog.
On 26 Apr 2006 22:12:02 -0700, "RicodJour" <[email protected]>
wrote:
>I have the same radius plane and I never use it. I find the can opener
>style corner edging tools much easier and faster to use.
I'm not sure which is worse, but I wouldn't go for those either.
I break arrises with 40 grit sandpaper, I round most stuff with a low
angle block plane, and for posh work with a definite radius I use an old
woodie rounder. This has a real iron and a real mouth, so it cuts
properly.
"Greg Guarino" <[email protected]> wrote in message
news:[email protected]...
> I've got a radius plane on order, this one:
>
> http://www.rockler.com/product.cfm?page=5320
>
> It's supposed to round over corners with a 1/16" radius. This brings
> up another probably silly question. Do I sand the flat sides of the
> (oak 1x2) wood first, then apply the radius plane? Will I then need to
> sand (gently, I suppose) the radius edge? Or do apply the plane to the
> unsanded wood, then sand the whole thing? Or do the coarse sanding
> first, or... what?
>
> Greg Guarino
I typically sand last regardless of what tool I use to shape the edges.