I would like to build some items (bookcases, buffet, dressers) out of oak
boards that I got. My experience with a tablesaw (King) is that I have
trouble doing nice straight cross-cuts on narrow and long boards, as well as
dados on such boards.
I tried building a sleigh to hold the wood, it helps but is not great.
I was looking into a radial-arm saw but a few people told me that they are
hard to adjust precisely and they always have some loose play left so they
do not make nice clean and straigth cuts.
Any ideas?
>I was looking into a radial-arm saw but a few people told me that they are
hard to adjust precisely and they always have some loose play left so they
do not make nice clean and straight cuts.
If you purchase one of the older DeWalts they hold their adjustment and
aren't loose and can do everything your TS can do and more.
(Did any of you expect a different comment from me???) LOL
--
Rumpty
Radial Arm Saw Forum: http://forums.delphiforums.com/woodbutcher/start
RC wrote:
> I would like to build some items (bookcases, buffet, dressers) out of
> oak boards that I got. My experience with a tablesaw (King) is that
> I have trouble doing nice straight cross-cuts on narrow and long
> boards, as well as dados on such boards.
>
> I tried building a sleigh to hold the wood, it helps but is not great.
>
> I was looking into a radial-arm saw but a few people told me that
> they are hard to adjust precisely and they always have some loose
> play left so they do not make nice clean and straigth cuts.
>
> Any ideas?
Have you considered using a router instead? I've used my radial arm saw for
dados but I actually prefer my router. You can build a jig to speed things
along quite easily.
--
Mortimer Schnerd, RN
[email protected]
http://www.mortimerschnerd.com
"RC" <[email protected]> wrote in message
news:[email protected]...
> I would like to build some items (bookcases, buffet, dressers) out of oak
> boards that I got. My experience with a tablesaw (King) is that I have
> trouble doing nice straight cross-cuts on narrow and long boards, as well
as
> dados on such boards.
>
> I tried building a sleigh to hold the wood, it helps but is not great.
>
> I was looking into a radial-arm saw but a few people told me that they are
> hard to adjust precisely and they always have some loose play left so they
> do not make nice clean and straigth cuts.
>
> Any ideas?
++++++++++++++++++++++++++
Dados on 6-7 or 8 foot long lumber is not that easy on most Tablesaws.. And
without a Radial Arm saw the best way is to use a router...a simple jig for
the router will make the task pretty easy...
Heck I own a Crapsman RAS that I purchased new in the late 60's that I
usually use for dado cuts...this saw is most likely the worst of the breed
(RAS) BUT it is not at all hard to adjust ..
And it will make precise cuts ..
HOWEVER it will not hold these adjustments very long IF you do everything
on it... Mine has not moved off 90 degrees in 25 years and honestly dispite
what everyone says I have no problems doing dados' with it...
The ONLY reason I still own the saw is because it does such a good job on
dado cuts....THE ONLY REASON !
otherwise it would have been history years ago and would have been replaced
with some configuration of a Miter Saw..
Use a router... and be done with it ...
Bob Griffiths
May I make a few suggestions?
maybe your problem is not your table saw, if you can have an easier way to
do your dados perhaps you would be please and you wouldn't have to spend big
bucks in a radial saw.....
-If you add a sliding table to your saw, that might be easier? and it can be
use for all sort of other cut too :-)
-dados with a router?
just my $0.02
good luck
--
Mike