Can anyone tell me the method Sam Maloof uses to create the curved,
7 rail backrest slats on his signature chairs?
With his penchant for free-handing things on a bandsaw (thus removing
various fingertips as well), I have imagined he might cut them from
solid stock. But could it be that he uses a more conventional method
such as steam bending?
I drew up a dining chair design loosely influenced by a mix of Queen
Anne, early 1800s American and Scandinavian, but fairly modern.
Comfort and clean lines were my major criteria for this design. I then
searched the web for anything similar, and found that Maloof backrest
slats are quite similar to my drawing. (Drawring to you Normites...)
I feel a massive new project coming up...
Thanks,
Greg G.
<<: Boy, you've got that part right. $2000 for a rocker and I could
: afford to throw out half my stock as well.
I think his start at 8-10 times that.
-- Andy Barss >>
Rest assured, they are starting now at something like 20K + for his
BASE line rocker that is also made with the help of his trained
craftsman.
Mr. Maloof is something like 82 or so, and is purported to have a
backlog of something like 5 years to get a base line rocker.
Robert
Greg G. wrote:
> I've seen video of him freehanding various parts, unsupported, and it
> made me a little queasy. I tried to cut a cylinder of wood, a long
> time ago, that took off like a spinning top. Left me WAY more
> appreciative of my intact fingers... and the potential for disaster on
> a bandsaw. (3tpi - 1/2" blade - makes for a fine meatcutter.)
> I think I'll try steam bending instead. I worry about consistancy,
> however - They have to match up pretty well.
Yeah, I always see him free-handing them. I even heard him say that he
doesn't recommend that for other people. I know he also likes to use
the router one-handed with roundover bits. I would probably go that
way only with guled laminations and a roundover bit in the table where
possible.
brian
Solid stock, freehand cut on a bandsaw He has templates
for everthing he's made more than one of. There's a
video "Sam Maloof Woodworking Profile"
ISBN 0-942391-26-8, from Taunton, that goes
through the making of one of his rocking chairs,
inlcuding the joinery, which you may want to
find and watch.(Taunton's number is 1-800-
888-8286 if you can't find it).
charlie b
BobS wrote:
>
> Greg,
>
> Unless I'm missing something, why not just mill some stock wide and thick
> enough to make the 7 slats from. Make a template, transfer it to the stock
> 7 times, then start cutting on the bandsaw. The stock would be flat (laying
> on the edge side of the slats) and you just follow near the cut line.
> Finish them up on a spindle sander.
>
> Bob S.
Well first, 1 1/2 1o 2" thick walnut .ain't easy to come by for a lot
of folks - though not a problem for Mr. Maloof who can have half his
original stock become cutoffs and scrap.
Second, the first bandsaw cuts do the "S" curve then you have to put
those back to make the next cuts for the curve to go from flat to
round
where they go into the chair seat and chair back.
And still photos don't even hint at what his video shows. 2-D stills
just don't convey how he sculpts on the bandsaw, hitting two lines
on adjacent faces which are both curved. It's pretty amazing to
see - and a bit scary. Freehanding with only one contact point on
the table is a touchy process. One hidden knot or hard spot, a tooth
catches rather than cuts and the end he's holding comes down very
quickly, with a lot of force, onto the unyielding cast iron table.
If you think a catch when turning is "interesting", try one on a
bandsaw - while free handing
Oh- the special router bits he had custom made for the back and
arms to the chair seat joints are now available to the rest of
us.
charlie b
On Sun, 30 Oct 2005 05:51:06 -0500, Greg G.<[email protected]> wrote:
>With his penchant for free-handing things on a bandsaw (thus removing
>various fingertips as well),
Out of interest, how many fingers does Maloof still have?
Greg,
Unless I'm missing something, why not just mill some stock wide and thick
enough to make the 7 slats from. Make a template, transfer it to the stock
7 times, then start cutting on the bandsaw. The stock would be flat (laying
on the edge side of the slats) and you just follow near the cut line.
Finish them up on a spindle sander.
Bob S.
"Greg G." <[email protected]> wrote in message
news:[email protected]...
>
>
> Can anyone tell me the method Sam Maloof uses to create the curved,
> 7 rail backrest slats on his signature chairs?
>
> With his penchant for free-handing things on a bandsaw (thus removing
> various fingertips as well), I have imagined he might cut them from
> solid stock. But could it be that he uses a more conventional method
> such as steam bending?
>
> I drew up a dining chair design loosely influenced by a mix of Queen
> Anne, early 1800s American and Scandinavian, but fairly modern.
> Comfort and clean lines were my major criteria for this design. I then
> searched the web for anything similar, and found that Maloof backrest
> slats are quite similar to my drawing. (Drawring to you Normites...)
>
> I feel a massive new project coming up...
>
> Thanks,
>
>
> Greg G.
<<Thanks for the links! Interesting articles, even though they
contained no revelations of his woodworking techniques.
Nevertheless, they were a refreshing look into the life of what
appears to be an exceedingly fine and generous gentleman.
A National Treasure indeed - not as much for his furniture, but his
philanthropy.>>
I have had a chance to chat with both of the authors shortly after they had
returned from their visits to Maloof's shop in California (one even got him
to autograph a copy of the magazine for me). In each case the guys were as
impressed with Maloof's humility as they were with his craftsmanship. One
or both of them occasionally visit the wreck so it is possible that he might
be able to provide the details you were seeking about Maloof's methods.
Lee
--
To e-mail, replace "bucketofspam" with "dleegordon"
_________________________________
Lee Gordon
http://www.leegordonproductions.com
"Greg G." wrote in message
> Didn't know much about Maloof, only that his chairs caught my eye
> years ago - even though I failed to recognize the name of the man who
> designed them. Made the connection to his name while watching a
> Modern Masters program on HGTV a couple of years ago that showed his
> unique style of bandsawing chair parts - and that is what stuck in my
> mind at the time - that and his curvy chair designs.
I do like the finish on his pieces. Also the rounded edges on drawer fronts,
rails, and stiles on his inset drawer cabinets caught my eye the first time
I saw them and I've heard since that it's his inspiration/influence.
It's all those little natural elements that add up to pleasing Maloof
designs, although I am normally much more of a functional
Stickley/Mission/Prairie/Bungalow kinda guy in my furniture and architecture
tastes.
--
www.e-woodshop.net
Last update: 10/22/05
Greg G. <[email protected]> wrote:
: charlie b said:
:>BobS wrote:
:>>
:>> Greg,
:>>
:>> Unless I'm missing something, why not just mill some stock wide and thick
:>> enough to make the 7 slats from. Make a template, transfer it to the stock
:>> 7 times, then start cutting on the bandsaw. The stock would be flat (laying
:>> on the edge side of the slats) and you just follow near the cut line.
:>> Finish them up on a spindle sander.
Isn't that going to create spindles with a lot of weak, short grain?
: Boy, you've got that part right. $2000 for a rocker and I could
: afford to throw out half my stock as well.
I think his start at 8-10 times that.
-- Andy Barss
Lee Gordon said:
><<Can anyone tell me the method Sam Maloof uses to create the curved,
>7 rail backrest slats on his signature chairs?>>
>
>A couple of publications have recently presented features on Maloof. Here's
>a link to the one that was in Woodcraft Magazine:
>http://woodcraftmagazine.com/articles/article.aspx?id=10
>
>And here's the one that was in Woodshop News:
>http://www.woodshopnews.com/ME2/dirmod.asp?sid=&nm=&type=Publishing&mod=Publications%3A%3AArticle&mid=8F3A7027421841978F18BE895F87F791&tier=4&id=F94616F04A90481D9AFCF1A3C459556B
>
>I'm not sure if either of these articles provides the precise information
>you are looking for but both are quite interesting. I seem to recall that
>one of the illustrations that accompanied one of these articles (I can't
>recall which) showed Maloof standing in his workshoop next to an impressive
>number of curved templates hanging on the wall. They looked like they could
>have been used as patterns for a router.
Thanks for the links! Interesting articles, even though they
contained no revelations of his woodworking techniques.
Nevertheless, they were a refreshing look into the life of what
appears to be an exceedingly fine and generous gentleman.
A National Treasure indeed - not as much for his furniture, but his
philanthropy.
Didn't know much about Maloof, only that his chairs caught my eye
years ago - even though I failed to recognize the name of the man who
designed them. Made the connection to his name while watching a
Modern Masters program on HGTV a couple of years ago that showed his
unique style of bandsawing chair parts - and that is what stuck in my
mind at the time - that and his curvy chair designs.
Greg G.
Swingman said:
>"Greg G." wrote in message
>
>> Can anyone tell me the method Sam Maloof uses to create the curved,
>> 7 rail backrest slats on his signature chairs?
>>
>> With his penchant for free-handing things on a bandsaw (thus removing
>> various fingertips as well), I have imagined he might cut them from
>> solid stock. But could it be that he uses a more conventional method
>> such as steam bending?
>
>Everything I've seen points to the former (bandsaw) ... I've seen many
>pictures of him doing exactly that with solid stock.
I've seen video of him freehanding various parts, unsupported, and it
made me a little queasy. I tried to cut a cylinder of wood, a long
time ago, that took off like a spinning top. Left me WAY more
appreciative of my intact fingers... and the potential for disaster on
a bandsaw. (3tpi - 1/2" blade - makes for a fine meatcutter.)
I think I'll try steam bending instead. I worry about consistancy,
however - They have to match up pretty well.
Greg G.
Andy Dingley said:
>On Sun, 30 Oct 2005 05:51:06 -0500, Greg G.<[email protected]> wrote:
>
>>With his penchant for free-handing things on a bandsaw (thus removing
>>various fingertips as well),
>
>Out of interest, how many fingers does Maloof still have?
It is my understanding that he still has them all.
But he has lost several finger tips due to...
( I am told, a jointer accident. - planer for you across the pond )
Greg G.
charlie,
Agreed, finding some 8/4 walnut may be difficult but not impossible by any
means - if that's what he's using but the OP didn't say anything about using
walnut.
I disagree about having to tape the "S" curved slats back together to cut
the transitions for the rounds. No matter whether he laminates them or cuts
from solid stock, they still need to be cut. Simply lay the slat flat on
the BS table and make the cuts - one at a time then do the final rounding
with a rasp and sanding.
As for free-handing on the bandsaw, I don't see where any single-point
free-handing is necessary to make the slats - look at one of Maloof's
rockers and I think you would agree. Whether he laminates the slats or makes
them from solid stock, the transitions for the rounds still need to be cut.
Simply laying the slat, flat on the BS table and making the cuts will get
the job done. Then, as Mr. Maloof does, he gets out his rasps, files and
then has assistants sand them for a week or two.
I don't think there's as much waste as one might think in making the slats.
If someone is making a heirloom piece out of a fine hardwood, then a few
extra dollars isn't really going to make a difference in the overall price.
I would bet that someone making laminations for the first time like these,
would waste more wood than making them out of solid stock to begin with.
As Greg stated, he did a lot of research so I imagine he came across the
many sites that show Maloof inspired rockers and although some used flat
slats, top to bottom, others made the slats similar to Maloof's. This type
of rocker is not made primarily with a tablesaw and as such requires a
person skilled or at least willing to learn how to use a bandsaw. I consider
my 1hp bandsaw a lot less dangerous than my 3hp tablesaw and certainly a
versatile tool.
I'm no expert on it but if there's a difficult piece to make, it's usually a
good fit for the bandsaw. Leave enough spare stock at the end so you can
handle the piece safely if you're free-handing it. Go slow enough so that
when you make a curved cut the blade has time to cut and you're not putting
a lateral load on the blade causing it to deflect, bind and then grab the
wood out of your hand. Also be sure your table is large enough.
There's several methods he can use to make these, from steam bending, cold
laminations, template and router to cutting them on the bandsaw. The
bandsaw appears to be the most effective method and certainly not the most
expensive when you consider what it takes to make the slats using other
methods.
Learn a new technique, practice it using scraps until your comfortable with
the whole process and do it safely - then go for the gold. It's called
woodworking.
Bob S.
"charlie b" <[email protected]> wrote in message
news:[email protected]...
> BobS wrote:
>>
>> Greg,
>>
>> Unless I'm missing something, why not just mill some stock wide and thick
>> enough to make the 7 slats from. Make a template, transfer it to the
>> stock
>> 7 times, then start cutting on the bandsaw. The stock would be flat
>> (laying
>> on the edge side of the slats) and you just follow near the cut line.
>> Finish them up on a spindle sander.
>>
>> Bob S.
>
> Well first, 1 1/2 1o 2" thick walnut .ain't easy to come by for a lot
> of folks - though not a problem for Mr. Maloof who can have half his
> original stock become cutoffs and scrap.
>
> Second, the first bandsaw cuts do the "S" curve then you have to put
> those back to make the next cuts for the curve to go from flat to
> round
> where they go into the chair seat and chair back.
>
> And still photos don't even hint at what his video shows. 2-D stills
> just don't convey how he sculpts on the bandsaw, hitting two lines
> on adjacent faces which are both curved. It's pretty amazing to
> see - and a bit scary. Freehanding with only one contact point on
> the table is a touchy process. One hidden knot or hard spot, a tooth
> catches rather than cuts and the end he's holding comes down very
> quickly, with a lot of force, onto the unyielding cast iron table.
> If you think a catch when turning is "interesting", try one on a
> bandsaw - while free handing
>
> Oh- the special router bits he had custom made for the back and
> arms to the chair seat joints are now available to the rest of
> us.
>
> charlie b
charlie b said:
>Solid stock, freehand cut on a bandsaw He has templates
>for everthing he's made more than one of. There's a
>video "Sam Maloof Woodworking Profile"
>ISBN 0-942391-26-8, from Taunton, that goes
>through the making of one of his rocking chairs,
>inlcuding the joinery, which you may want to
>find and watch.(Taunton's number is 1-800-
>888-8286 if you can't find it).
>
>charlie b
Thanks for the info - our library doesn't have it. :-(
Every video is another chunk of wood or tool I won't be getting. ;-)
I do subscribe to FWW magazine, however - they had a recent blurb
about Maloof but nothing useful about technique. I've seen video of
his shop on Modern Masters - templates everywhere.
Greg G.
An easy method that doesn't involve complicated bandsawing (and Mallof lost
his fingertip on a jointer, not a bandsaw) is to do a stack lamination glue
up. I've done this for a couple of rockers I've built. Gives you good
control over the shape and the consistency between the different spindles.
Build yourself a glue up form of the shape you want, cut a bunch of 1/8 or
so strips of the wood you'll use and glue and clamp to the form. It's really
pretty easy and results are good. Plus it gives you the option to add some
contrasting woods to the glue up for a litte diversity. Stack lamination is
how Maloof does the rockers and the attachments of the rockers to his legs.
Gary in KC
"Greg G." <[email protected]> wrote in message
news:[email protected]...
>
>
> Can anyone tell me the method Sam Maloof uses to create the curved,
> 7 rail backrest slats on his signature chairs?
>
> With his penchant for free-handing things on a bandsaw (thus removing
> various fingertips as well), I have imagined he might cut them from
> solid stock. But could it be that he uses a more conventional method
> such as steam bending?
>
> I drew up a dining chair design loosely influenced by a mix of Queen
> Anne, early 1800s American and Scandinavian, but fairly modern.
> Comfort and clean lines were my major criteria for this design. I then
> searched the web for anything similar, and found that Maloof backrest
> slats are quite similar to my drawing. (Drawring to you Normites...)
>
> I feel a massive new project coming up...
>
> Thanks,
>
>
> Greg G.
charlie b said:
>BobS wrote:
>>
>> Greg,
>>
>> Unless I'm missing something, why not just mill some stock wide and thick
>> enough to make the 7 slats from. Make a template, transfer it to the stock
>> 7 times, then start cutting on the bandsaw. The stock would be flat (laying
>> on the edge side of the slats) and you just follow near the cut line.
>> Finish them up on a spindle sander.
>>
>> Bob S.
>
> Well first, 1 1/2 1o 2" thick walnut .ain't easy to come by for a lot
> of folks - though not a problem for Mr. Maloof who can have half his
> original stock become cutoffs and scrap.
Boy, you've got that part right. $2000 for a rocker and I could
afford to throw out half my stock as well. I'm so poor, I have to cut
down cherry trees in my yard for lumber - and then wait 3 years to use
what hasn't split. ;-)
> Second, the first bandsaw cuts do the "S" curve then you have to put
> those back to make the next cuts for the curve to go from flat to
> round where they go into the chair seat and chair back.
Well, I'm not trying to emulate his work, I just saw that his design
has the same style of slat as my design. I can deal with differences.
> And still photos don't even hint at what his video shows. 2-D stills
> just don't convey how he sculpts on the bandsaw, hitting two lines
> on adjacent faces which are both curved. It's pretty amazing to
> see - and a bit scary. Freehanding with only one contact point on
> the table is a touchy process. One hidden knot or hard spot, a tooth
> catches rather than cuts and the end he's holding comes down very
> quickly, with a lot of force, onto the unyielding cast iron table.
> If you think a catch when turning is "interesting", try one on a
> bandsaw - while free handing
That's for sure. I've seen a video of him working, and I now
understand why he has several missing fingertips. I was a complete
novice when I saw him freehanding a rail on the bandsaw and freaked.
And no, I didn't try if for myself, and probably never will. I prefer
jigs and other "disposable" objects to be shredded by a fast moving
blade as opposed to my most valued body parts. Nothing that endangers
my fingers, hands or eyes. I'd rather loose Mr. Winkey!
> Oh- the special router bits he had custom made for the back and
> arms to the chair seat joints are now available to the rest of
> us.
And where would that be? Whiteside? Amana?
I've often wondered how he did those, thinking perhaps through hours
and hours of sanding - but apparently not.
Greg G.
<<Can anyone tell me the method Sam Maloof uses to create the curved,
7 rail backrest slats on his signature chairs?>>
A couple of publications have recently presented features on Maloof. Here's
a link to the one that was in Woodcraft Magazine:
http://woodcraftmagazine.com/articles/article.aspx?id=10
And here's the one that was in Woodshop News:
http://www.woodshopnews.com/ME2/dirmod.asp?sid=&nm=&type=Publishing&mod=Publications%3A%3AArticle&mid=8F3A7027421841978F18BE895F87F791&tier=4&id=F94616F04A90481D9AFCF1A3C459556B
I'm not sure if either of these articles provides the precise information
you are looking for but both are quite interesting. I seem to recall that
one of the illustrations that accompanied one of these articles (I can't
recall which) showed Maloof standing in his workshoop next to an impressive
number of curved templates hanging on the wall. They looked like they could
have been used as patterns for a router.
Lee
--
To e-mail, replace "bucketofspam" with "dleegordon"
_________________________________
Lee Gordon
http://www.leegordonproductions.com
"Greg G." wrote in message
> Can anyone tell me the method Sam Maloof uses to create the curved,
> 7 rail backrest slats on his signature chairs?
>
> With his penchant for free-handing things on a bandsaw (thus removing
> various fingertips as well), I have imagined he might cut them from
> solid stock. But could it be that he uses a more conventional method
> such as steam bending?
Everything I've seen points to the former (bandsaw) ... I've seen many
pictures of him doing exactly that with solid stock.
--
www.e-woodshop.net
Last update: 10/22/05