I figured wood workers might be a good group to post this question to.
Was building an outdoor shed in our back yard. Had a lot of tools out
there. Foolishly trusted the weather man who claimed no chance of
showers.
We caught a pop of thunder shower today. Had all my tools for the shed
outside. Got rained on hard for 15 minutes. Wondering if there is any
advice on how to handle them. I dried them all off (
and took them inside). But was wondering if sraying them internally
with WD40 for its water displacement qualities would help - or any
other suggestion.
Left out tools: framing nail gun, pancacke compressor, circular sawm
drill.
Many thanks!
Thanks for all the replies folks! Great ideas. Since my wife would
kill me if my power tools invader her oven, going to try the rubbing
alcohol first. Many, many thanks.
Rob Mills wrote:
> "Mortimer Schnerd, RN" <[email protected]> wrote in message
> news:[email protected]...
>
>
> >>> You know, when you have water trapped in your ear after swimming,
> >>> pouring a
> little rubbing alcohol will cause it to dry almost immediately.<<<
>
>
> The best thing I ever used to dry out wet ignition wires was either (diesel
> starting fluid) that is available at most truck stops. You sure don't want
> to fire things up until the either is completely evaperated. RM~
Hmmmm.....
I dunno. When I get caught in the rain, which does happen (think
decking a house when a big storm is coming) and cannot stop, our tools
get soaked. Ditto when we go to a job and get caught in an unexpected
frog strangler while sitting in traffic (no doubt caused by rain).
We use WD40 on the nails, not on the tools. Try this: spray WD40 on a
piece of metal, and let it dry. It leaves a film behind. This film
attracts dirt, lint, etc. and makes it into gum on moving surfaces. I
sure wouldn't recommend using it on the tools, inside or out. My tool
repair guy can tell in a minute when the armatures or brushes are
gummed up that someone has been using WD40. That is why my favorite
gunsmith told me to quit using it on my shotguns.
Acetone, etc., will dissolve or etch most plastics. I ruined some of
my drill and saw cases as I was industriously cleaning off tar from the
cases and I noticed the plastic became gummy. Can you imagine what
would happen to the varnish on your motor windings if you did this?
As far as your nail gun goes, forget it. No harm, no foul. How much
water do you drain out of your compressor tank every day? We are
usually in for a few ounces, depending on the season. The point is
this: is you are using a compressor to power your nailers and sanders
and do not have a drying system of filters in place, they are already
exposed to a lot of moisture. If you didn't have a funnel to channel
the water into the housing, you should be fine. Many mornings in the
south where we have extreme temp changes and high humidity you can
actually see the condensation coming out of the exhaust port of the gun
on the high usage guns like roofing nailers and staplers.
So what to do when they get wet? We dry everything off as quickly and
completely as possible. If we have the compressor on site, we blow out
the tools till dry, have some coffee and get back to work. Ideally,
we dry with a cloth, blow them out, and then let them sit overnight
before using.
Never lost one tool to rain as you described... lost plenty to rust,
though.
Robert
Put them on a heat register in your house, let the heat blow on them for
about a week. They'll work as good as new.
Bob
<[email protected]> wrote in message
news:[email protected]...
>I figured wood workers might be a good group to post this question to.
> Was building an outdoor shed in our back yard. Had a lot of tools out
> there. Foolishly trusted the weather man who claimed no chance of
> showers.
>
> We caught a pop of thunder shower today. Had all my tools for the shed
> outside. Got rained on hard for 15 minutes. Wondering if there is any
> advice on how to handle them. I dried them all off (
> and took them inside). But was wondering if sraying them internally
> with WD40 for its water displacement qualities would help - or any
> other suggestion.
>
> Left out tools: framing nail gun, pancacke compressor, circular sawm
> drill.
>
> Many thanks!
>
On Sat, 13 Aug 2005 19:41:32 GMT, Joe Mama <[email protected]> wrote:
> A little water won't hurt these tools. My stuff gets wet on jobs all
>the time. Have a 20 year old Air-O-Smith compressor that has been wet
>too many times to count and it still works fine. Never use WD40 on
>lubricated parts. It will wash the lubricant off then dry out leaving
>nothing to keep the part lubricated.
> Rabbit
hmm... interesting brand... does it sing "dream on" a lot? *g*
mac
Please remove splinters before emailing
"Mortimer Schnerd, RN" <[email protected]> wrote in message
news:[email protected]...
>>> You know, when you have water trapped in your ear after swimming,
>>> pouring a
little rubbing alcohol will cause it to dry almost immediately.<<<
The best thing I ever used to dry out wet ignition wires was either (diesel
starting fluid) that is available at most truck stops. You sure don't want
to fire things up until the either is completely evaperated. RM~
Take a hair dryer to it...couldn't hurt...
Tina
<[email protected]> wrote in message
news:PgUIe.125769$s54.120028@pd7tw2no...
> Just shake them a bit make sure all the water is out. I do concrete form
> work and we work in the sand and water. NEVER a problem. Left a pinner
> (BOSH hammer drill) in an inch of water picked it up and started working
NO
> PROBLEMS
>
> --
>
>
> Http://www.powertool-reviews.com
>
> <[email protected]> wrote in message
> news:[email protected]...
> >I figured wood workers might be a good group to post this question to.
> > Was building an outdoor shed in our back yard. Had a lot of tools out
> > there. Foolishly trusted the weather man who claimed no chance of
> > showers.
> >
> > We caught a pop of thunder shower today. Had all my tools for the shed
> > outside. Got rained on hard for 15 minutes. Wondering if there is any
> > advice on how to handle them. I dried them all off (
> > and took them inside). But was wondering if sraying them internally
> > with WD40 for its water displacement qualities would help - or any
> > other suggestion.
> >
> > Left out tools: framing nail gun, pancacke compressor, circular sawm
> > drill.
> >
> > Many thanks!
> >
>
>
James "Cubby" Culbertson wrote:
> Friendly warning....let em air a while after the alcohol. I could see
> myself setting my power drill on fire!
>
Snip
I'd SECOND that.
A few years ago I had a CIG "Little Beaver" Spray system. Kind of like a
vacuum unit. Anyhow it started to make some horrendous noises so I
pulled it apart cleaned out the dust and gave it a good spray of WD40.
Put it all back together and had a serious brain fart. Fired it up and
bloody thing near blew apart. Scared the living Christ out of me.
Needless to say, it was a good excuse to get my first real compressor.
Quietened it down though :)
regards
John
I would put the saw and drill in the oven with the door open and set to the
"Keep Warm" setting for a couple of hours before applying power. The air
nailer should be treated with a rust preventative such as WD-40 and
lubricated internally with the recommended oil. If you have another
compressor I'd try to gently blow out any water that got into the motor of
the pancake compressor. If that is not possible I'd use a hair dryer to dry
out the moisture. Don't cook the motor to death, just warm to the touch for
an hour of so.
Don Dando
<[email protected]> wrote in message
news:[email protected]...
> I figured wood workers might be a good group to post this question to.
> Was building an outdoor shed in our back yard. Had a lot of tools out
> there. Foolishly trusted the weather man who claimed no chance of
> showers.
>
> We caught a pop of thunder shower today. Had all my tools for the shed
> outside. Got rained on hard for 15 minutes. Wondering if there is any
> advice on how to handle them. I dried them all off (
> and took them inside). But was wondering if sraying them internally
> with WD40 for its water displacement qualities would help - or any
> other suggestion.
>
> Left out tools: framing nail gun, pancacke compressor, circular sawm
> drill.
>
> Many thanks!
>
125 should be fine, maybe 2-3 hr...no need to take a chance with the
plastic. All you can do is evaporate the water. Rain doesn't leave much
behind.
Wilson
"Lew Hodgett" <[email protected]> wrote in message
news:[email protected]...
> RE: Subject
>
> Turn on your oven at about 150-175F and place tools in the oven for an
> hour or so, then allow to cool to room temp.
>
> Heat does a great job of vaporizing water, if you don't over do it.
>
> As far as WD40, like chicken soup, no medicinal value but hadn't oughta
> hurt!
>
> Lew
Just shake them a bit make sure all the water is out. I do concrete form
work and we work in the sand and water. NEVER a problem. Left a pinner
(BOSH hammer drill) in an inch of water picked it up and started working NO
PROBLEMS
--
Http://www.powertool-reviews.com
<[email protected]> wrote in message
news:[email protected]...
>I figured wood workers might be a good group to post this question to.
> Was building an outdoor shed in our back yard. Had a lot of tools out
> there. Foolishly trusted the weather man who claimed no chance of
> showers.
>
> We caught a pop of thunder shower today. Had all my tools for the shed
> outside. Got rained on hard for 15 minutes. Wondering if there is any
> advice on how to handle them. I dried them all off (
> and took them inside). But was wondering if sraying them internally
> with WD40 for its water displacement qualities would help - or any
> other suggestion.
>
> Left out tools: framing nail gun, pancacke compressor, circular sawm
> drill.
>
> Many thanks!
>
A little water won't hurt these tools. My stuff gets wet on jobs all
the time. Have a 20 year old Air-O-Smith compressor that has been wet
too many times to count and it still works fine. Never use WD40 on
lubricated parts. It will wash the lubricant off then dry out leaving
nothing to keep the part lubricated.
Rabbit
--
--
Lon Marshall <[email protected]>
<[email protected]> wrote in message
news:[email protected]...
> Thanks for all the replies folks! Great ideas. Since my wife would
> kill me if my power tools invader her oven, going to try the rubbing
> alcohol first. Many, many thanks.
I know this may seem silly but, why didn't you take 25 seconds to put the
tools under cover during the storm.
Why on earth just sit there for 15 min watching them get soaked?
Am I missing something here?
James "Cubby" Culbertson wrote:
> I've had the same thing happen to me a number of times. You'd think I'd
> learn!
> I suppose WD40 would work ok but I find it tends to gather dirt later on and
> I probably wouldn't go that route.
You know, when you have water trapped in your ear after swimming, pouring a
little rubbing alcohol will cause it to dry almost immediately. I don't know
what effect it might have on the plastic parts but I wonder what would happen if
you poured some alcohol in them, then hitting them hard with compressed air?
--
Mortimer Schnerd, RN
[email protected]
It sounds like he trusted the weather predictions, left them out, and left
the house. Came back and the storm had hit. At least that's what's
happened to me in the past.
Cheers,
cc
"Battleax" <[email protected]> wrote in message
news:[email protected]...
>
> <[email protected]> wrote in message
> news:[email protected]...
>> Thanks for all the replies folks! Great ideas. Since my wife would
>> kill me if my power tools invader her oven, going to try the rubbing
>> alcohol first. Many, many thanks.
>
>
> I know this may seem silly but, why didn't you take 25 seconds to put the
> tools under cover during the storm.
> Why on earth just sit there for 15 min watching them get soaked?
> Am I missing something here?
>
>
On 5 Aug 2005 14:27:28 -0700, [email protected] wrote:
>I figured wood workers might be a good group to post this question to.
>Was building an outdoor shed in our back yard. Had a lot of tools out
>there. Foolishly trusted the weather man who claimed no chance of
>showers.
>
>We caught a pop of thunder shower today. Had all my tools for the shed
>outside. Got rained on hard for 15 minutes. Wondering if there is any
>advice on how to handle them. I dried them all off (
>and took them inside). But was wondering if sraying them internally
>with WD40 for its water displacement qualities would help - or any
>other suggestion.
>
>Left out tools: framing nail gun, pancacke compressor, circular sawm
>drill.
Nothing. What do you think construction workers do when it starts
raining? You may or may not get a little rust on consumable parts
like blades or drill bits, but the tools you listed are designed and
intended for use outdoors. Being outside means rain sometimes, and
most tools are just fine after a little moisture. If they start to
get really rusty, polish them up a bit, and wipe some oil on them, or
spray some WD-40. Don't get to worked up about it- if you've got
anything that could be described as a decent tool, it'll be fine.
Those tools are for use- not for looking at!
I've had the same thing happen to me a number of times. You'd think I'd
learn!
I suppose WD40 would work ok but I find it tends to gather dirt later on and
I probably wouldn't go that route.
If you need to use the tools soon, hit them pretty good with compressed air
until you are certain there is no water
in them. I've usually just used it as an excuse to relax a while while
they dry out!
Good luck,
Cheers,
cc
<[email protected]> wrote in message
news:[email protected]...
>I figured wood workers might be a good group to post this question to.
> Was building an outdoor shed in our back yard. Had a lot of tools out
> there. Foolishly trusted the weather man who claimed no chance of
> showers.
>
> We caught a pop of thunder shower today. Had all my tools for the shed
> outside. Got rained on hard for 15 minutes. Wondering if there is any
> advice on how to handle them. I dried them all off (
> and took them inside). But was wondering if sraying them internally
> with WD40 for its water displacement qualities would help - or any
> other suggestion.
>
> Left out tools: framing nail gun, pancacke compressor, circular sawm
> drill.
>
> Many thanks!
>
On Sat, 6 Aug 2005 22:19:53 -0500, "bob"
<[email protected]> wrote:
>Put them on a heat register in your house, let the heat blow on them for
>about a week. They'll work as good as new.
>
Better yet just put them in the auto in the sun with the windows
closed, when the windows are not steamy they are done.
And yes a tongue might be slightly askew here.
Mark
><[email protected]> wrote in message
>news:[email protected]...
>>I figured wood workers might be a good group to post this question to.
>> Was building an outdoor shed in our back yard. Had a lot of tools out
>> there. Foolishly trusted the weather man who claimed no chance of
>> showers.
Friendly warning....let em air a while after the alcohol. I could see
myself setting my power drill on fire!
<[email protected]> wrote in message
news:[email protected]...
> Thanks for all the replies folks! Great ideas. Since my wife would
> kill me if my power tools invader her oven, going to try the rubbing
> alcohol first. Many, many thanks.
>
> Rob Mills wrote:
>> "Mortimer Schnerd, RN" <[email protected]> wrote in
>> message
>> news:[email protected]...
>>
>>
>> >>> You know, when you have water trapped in your ear after swimming,
>> >>> pouring a
>> little rubbing alcohol will cause it to dry almost immediately.<<<
>>
>>
>> The best thing I ever used to dry out wet ignition wires was either
>> (diesel
>> starting fluid) that is available at most truck stops. You sure don't
>> want
>> to fire things up until the either is completely evaperated. RM~
>