I saw the posting about the best tip you found on the NG. I have to agree
that Doug S's one of shooting nails through a piece of tape is one of the
best I ever found. I don't know if this one is new, but I "invented" it
today for myself. It may have been done before but I've never seen it
anywhere.
My helper has a tendency to push really hard on the drill when drilling
pocket holes in a kreg jig. The next thing I know, all the pocket holes are
too deep because he pushed the stop collar down the shaft of the drill bit.
Upon finding this out AGAIN this morning, I realized I could cut about 3/4"
off the bottom of the drill bit so there was no bit left between the collar
and the chuck of the drill. Now there's no way the collar will slide up the
bit and make the holes too deep. I used to grind a small flat spot on the
bits for the set screw, but there would still be play in that idea if I
didn't make the slot deep enough.
Just thought it might help someone with similar problems
--
Rick Nagy
Johnstown, PA
[email protected] - Remove nospam to email me
Be sure to check out my website at http://www.rickscabinetshop.com
I never use 2 x stock, not only that, wouldn't the 2x stock still sit in the
same place in the jig? I don't have the fancy Kreg, just the simple one.
--
Rick Nagy
Johnstown, PA
[email protected] - Remove nospam to email me
Be sure to check out my website at http://www.rickscabinetshop.com
"Leon" <[email protected]> wrote in message
news:[email protected]...
>
> "Rick's Cabinet Shop" <[email protected]> wrote in message
> news:ygb2h.4099$B44.3355@trndny07...
>>I saw the posting about the best tip you found on the NG. I have to agree
>>that Doug S's one of shooting nails through a piece of tape is one of the
>>best I ever found. I don't know if this one is new, but I "invented" it
>>today for myself. It may have been done before but I've never seen it
>>anywhere.
>>
>> My helper has a tendency to push really hard on the drill when drilling
>> pocket holes in a kreg jig. The next thing I know, all the pocket holes
>> are too deep because he pushed the stop collar down the shaft of the
>> drill bit. Upon finding this out AGAIN this morning, I realized I could
>> cut about 3/4" off the bottom of the drill bit so there was no bit left
>> between the collar and the chuck of the drill. Now there's no way the
>> collar will slide up the bit and make the holes too deep. I used to
>> grind a small flat spot on the bits for the set screw, but there would
>> still be play in that idea if I didn't make the slot deep enough.
>>
>> Just thought it might help someone with similar problems
>
>
> Good idea until you need to drill pocket holes for 2x stock, then you
> want a longer bit.
>
Rick's Cabinet Shop wrote:
> I saw the posting about the best tip you found on the NG. I have to agree
> that Doug S's one of shooting nails through a piece of tape is one of the
> best I ever found. I don't know if this one is new, but I "invented" it
> today for myself. It may have been done before but I've never seen it
> anywhere.
>
> My helper has a tendency to push really hard on the drill when drilling
> pocket holes in a kreg jig. The next thing I know, all the pocket holes are
> too deep because he pushed the stop collar down the shaft of the drill bit.
> Upon finding this out AGAIN this morning, I realized I could cut about 3/4"
> off the bottom of the drill bit so there was no bit left between the collar
> and the chuck of the drill. Now there's no way the collar will slide up the
> bit and make the holes too deep. I used to grind a small flat spot on the
> bits for the set screw, but there would still be play in that idea if I
> didn't make the slot deep enough.
>
> Just thought it might help someone with similar problems
An interesting solution. Is the helper someone who shows an interest
in the work, or just a body earning some bucks? If it's the former he
probably should be taught to let the tools do the work and to clear out
the holes rather than forcing it. Maybe a financial penalty or
incentive? Normally I'd say a smack to the back of the head, but this
is a family newsgroup. ;)
R
Rick's Cabinet Shop wrote:
> He shows some good interest and potential, but for some reason, everyone
> that ever helped me out, including my dad, always feels the need to slam
> through the wood when drilling pocket holes. I try to tell them to take it
> easy, but it never works. I usually keep my "good bit" marked with a
> sharpie, that way he knows to put the crappy one in before he starts...
> hmmmmmm maybe another good tip!
How about explaining to him how you'll be helping him get started in
the business. Any time he needs a special tool you'll buy it for him
and deduct it from his paycheck. The tools are his to keep when he
leaves.
R
Rick's Cabinet Shop wrote:
> My helper has a tendency to push really hard on the drill when drilling
> pocket holes in a kreg jig. The next thing I know, all the pocket holes are
> too deep because he pushed the stop collar down the shaft of the drill bit.
> Upon finding this out AGAIN this morning, I realized I could cut about 3/4"
> off the bottom of the drill bit so there was no bit left between the collar
> and the chuck of the drill. Now there's no way the collar will slide up the
> bit and make the holes too deep. I used to grind a small flat spot on the
> bits for the set screw, but there would still be play in that idea if I
> didn't make the slot deep enough.
You could cut a piece of skinny pvc tubing just long enough to go
between the chuck and the collar. That way, it wouldn't move. And it
would be easier to cut than the bit.
brian
On Nov 1, 9:11 pm, "RicodJour" <[email protected]> wrote:
[snip]How about explaining to him how you'll be helping him get started
in
> the business. Any time he needs a special tool you'll buy it for him
> and deduct it from his paycheck. The tools are his to keep when he
> leaves.
>
> R
You bad! *G*
Leon (in [email protected]) said:
| "Rick's Cabinet Shop" <[email protected]> wrote in
| message news:ygb2h.4099$B44.3355@trndny07...
<snip>
|| My helper has a tendency to push really hard on the drill when
|| drilling pocket holes in a kreg jig. The next thing I know, all
|| the pocket holes are too deep because he pushed the stop collar
|| down the shaft of the drill bit. Upon finding this out AGAIN this
|| morning, I realized I could cut about 3/4" off the bottom of the
|| drill bit so there was no bit left between the collar and the
|| chuck of the drill. Now there's no way the collar will slide up
|| the bit and make the holes too deep. I used to grind a small flat
|| spot on the bits for the set screw, but there would still be play
|| in that idea if I didn't make the slot deep enough.
||
|| Just thought it might help someone with similar problems
|
|
| Good idea until you need to drill pocket holes for 2x stock, then
| you want a longer bit.
Hmm. I keep two bits set up with stop collars - one for 3/4" stock and
one for 2x stock.
I haven't had a problem with the collars slipping; but wonder if a
smear of Loc-Tite (whatever the weakest type is) between the bit and
the collar might help prevent the problem...
--
Morris Dovey
DeSoto Solar
DeSoto, Iowa USA
http://www.iedu.com/DeSoto
On Thu, 02 Nov 2006 01:29:32 GMT, "Rick's Cabinet Shop"
<[email protected]> wrote:
>I never use 2 x stock, not only that, wouldn't the 2x stock still sit in the
>same place in the jig? I don't have the fancy Kreg, just the simple one.
There's an extension block that you can attach to the front of the
jig. The point being the screw ends up in the middle of the stock.
But the hell with that, the few times I've put a pocket screw in
something thicker than 3/4 I left the jig and bit setting alone.
I did have the collar slip on me once when I first got the jig. I
hate to overtighten those allen head screws cuz the damn wrench always
ends up getting stuck. Never happened again. I did think to mark the
bit behind the collar so I could see if it slipped, but never got
around to it.
-Leuf
That was almost the solution the other day when a 1/2 full can of Sherwin
Williams BAC wiping stain hit the floor, spilling and splashing all over the
router station and up the walls.....
--
Rick Nagy
Johnstown, PA
[email protected] - Remove nospam to email me
Be sure to check out my website at http://www.rickscabinetshop.com
"CW" <[email protected]> wrote in message
news:[email protected]...
> Do you happen to have a cutoff laying around about 2"x2"x36"? If so, the
> proper application of that cutoff to said helper should alleviate the
> problem. My have to do this twice but seldom does it take more than that.
>
> "Rick's Cabinet Shop" <[email protected]> wrote in message
> news:ygb2h.4099$B44.3355@trndny07...
>> I saw the posting about the best tip you found on the NG. I have to
>> agree
>> that Doug S's one of shooting nails through a piece of tape is one of the
>> best I ever found. I don't know if this one is new, but I "invented" it
>> today for myself. It may have been done before but I've never seen it
>> anywhere.
>>
>> My helper has a tendency to push really hard on the drill when drilling
>> pocket holes in a kreg jig. The next thing I know, all the pocket holes
> are
>> too deep because he pushed the stop collar down the shaft of the drill
> bit.
>> Upon finding this out AGAIN this morning, I realized I could cut about
> 3/4"
>> off the bottom of the drill bit so there was no bit left between the
> collar
>> and the chuck of the drill. Now there's no way the collar will slide up
> the
>> bit and make the holes too deep. I used to grind a small flat spot on
>> the
>> bits for the set screw, but there would still be play in that idea if I
>> didn't make the slot deep enough.
>>
>> Just thought it might help someone with similar problems
>>
>> --
>> Rick Nagy
>> Johnstown, PA
>>
>> [email protected] - Remove nospam to email me
>> Be sure to check out my website at http://www.rickscabinetshop.com
>>
>>
>
>
Do you happen to have a cutoff laying around about 2"x2"x36"? If so, the
proper application of that cutoff to said helper should alleviate the
problem. My have to do this twice but seldom does it take more than that.
"Rick's Cabinet Shop" <[email protected]> wrote in message
news:ygb2h.4099$B44.3355@trndny07...
> I saw the posting about the best tip you found on the NG. I have to agree
> that Doug S's one of shooting nails through a piece of tape is one of the
> best I ever found. I don't know if this one is new, but I "invented" it
> today for myself. It may have been done before but I've never seen it
> anywhere.
>
> My helper has a tendency to push really hard on the drill when drilling
> pocket holes in a kreg jig. The next thing I know, all the pocket holes
are
> too deep because he pushed the stop collar down the shaft of the drill
bit.
> Upon finding this out AGAIN this morning, I realized I could cut about
3/4"
> off the bottom of the drill bit so there was no bit left between the
collar
> and the chuck of the drill. Now there's no way the collar will slide up
the
> bit and make the holes too deep. I used to grind a small flat spot on the
> bits for the set screw, but there would still be play in that idea if I
> didn't make the slot deep enough.
>
> Just thought it might help someone with similar problems
>
> --
> Rick Nagy
> Johnstown, PA
>
> [email protected] - Remove nospam to email me
> Be sure to check out my website at http://www.rickscabinetshop.com
>
>
"Rick's Cabinet Shop" <[email protected]> wrote in message
news:ygb2h.4099
They shoot horses don't they???
He shows some good interest and potential, but for some reason, everyone
that ever helped me out, including my dad, always feels the need to slam
through the wood when drilling pocket holes. I try to tell them to take it
easy, but it never works. I usually keep my "good bit" marked with a
sharpie, that way he knows to put the crappy one in before he starts...
hmmmmmm maybe another good tip!
--
Rick Nagy
Johnstown, PA
[email protected] - Remove nospam to email me
Be sure to check out my website at http://www.rickscabinetshop.com
"RicodJour" <[email protected]> wrote in message
news:[email protected]...
> Rick's Cabinet Shop wrote:
>> I saw the posting about the best tip you found on the NG. I have to
>> agree
>> that Doug S's one of shooting nails through a piece of tape is one of the
>> best I ever found. I don't know if this one is new, but I "invented" it
>> today for myself. It may have been done before but I've never seen it
>> anywhere.
>>
>> My helper has a tendency to push really hard on the drill when drilling
>> pocket holes in a kreg jig. The next thing I know, all the pocket holes
>> are
>> too deep because he pushed the stop collar down the shaft of the drill
>> bit.
>> Upon finding this out AGAIN this morning, I realized I could cut about
>> 3/4"
>> off the bottom of the drill bit so there was no bit left between the
>> collar
>> and the chuck of the drill. Now there's no way the collar will slide up
>> the
>> bit and make the holes too deep. I used to grind a small flat spot on
>> the
>> bits for the set screw, but there would still be play in that idea if I
>> didn't make the slot deep enough.
>>
>> Just thought it might help someone with similar problems
>
> An interesting solution. Is the helper someone who shows an interest
> in the work, or just a body earning some bucks? If it's the former he
> probably should be taught to let the tools do the work and to clear out
> the holes rather than forcing it. Maybe a financial penalty or
> incentive? Normally I'd say a smack to the back of the head, but this
> is a family newsgroup. ;)
>
> R
>
"Rick's Cabinet Shop" <[email protected]> wrote in message
news:ygb2h.4099$B44.3355@trndny07...
>I saw the posting about the best tip you found on the NG. I have to agree
>that Doug S's one of shooting nails through a piece of tape is one of the
>best I ever found. I don't know if this one is new, but I "invented" it
>today for myself. It may have been done before but I've never seen it
>anywhere.
>
> My helper has a tendency to push really hard on the drill when drilling
> pocket holes in a kreg jig. The next thing I know, all the pocket holes
> are too deep because he pushed the stop collar down the shaft of the drill
> bit. Upon finding this out AGAIN this morning, I realized I could cut
> about 3/4" off the bottom of the drill bit so there was no bit left
> between the collar and the chuck of the drill. Now there's no way the
> collar will slide up the bit and make the holes too deep. I used to grind
> a small flat spot on the bits for the set screw, but there would still be
> play in that idea if I didn't make the slot deep enough.
>
> Just thought it might help someone with similar problems
Good idea until you need to drill pocket holes for 2x stock, then you want
a longer bit.