I'm making my first project with drawers and discovered I am clueless as
to how much clearance is needed between the drawer face (the drawers are
inset) and the frame. I did a mock-up with 1/8 inch, but that seems way
too big and doesn't look good. The wood is quartered white oak. Any
enlightenment as to how much clearance is necessary will be appreciated.
Mike
On Oct 22, 2:36=A0pm, Swingman <[email protected]> wrote:
> On 10/22/2011 12:56 PM, Mike wrote:
>
> > I'm making my first project with drawers and discovered I am clueless a=
s
> > to how much clearance is needed between the drawer face (the drawers ar=
e
> > inset) and the frame. I did a mock-up with 1/8 inch, but that seems way
> > too big and doesn't look good. The wood is quartered white oak. Any
> > enlightenment as to how much clearance is necessary will be appreciated=
.
>
> > Mike
>
> My preference is no more than 1/16th on inset drawers.
>
> Slides or runners?
>
> If the drawer is sitting on wooden runners, one of the problems with
> inset drawers is getting that bottom "gap" to equal the gap around the
> two sides and top, and to stay that way.
>
> A neat tip/trick on inset drawers is to plane a very small "rabbet" on
> the bottom of the front edge of the drawer front. Make this small rabbet
> equal in depth to the distance of your fitted gap around the top and two
> sides. This way, your drawer, even though sitting flat on the runners,
> will appear to have the same width gap all around.
>
> --www.eWoodShop.com
> Last update: 4/15/2010
> KarlCaillouet@ (the obvious)http://gplus.to/eWoodShop
(or use Blum Metabox....g,d&r)
Robatoy <[email protected]> wrote:
> On Oct 22, 2:36 pm, Swingman <[email protected]> wrote:
>> On 10/22/2011 12:56 PM, Mike wrote:
>>
>>> I'm making my first project with drawers and discovered I am clueless as
>>> to how much clearance is needed between the drawer face (the drawers are
>>> inset) and the frame. I did a mock-up with 1/8 inch, but that seems way
>>> too big and doesn't look good. The wood is quartered white oak. Any
>>> enlightenment as to how much clearance is necessary will be appreciated.
>>
>>> Mike
>>
>> My preference is no more than 1/16th on inset drawers.
>>
>> Slides or runners?
>>
>> If the drawer is sitting on wooden runners, one of the problems with
>> inset drawers is getting that bottom "gap" to equal the gap around the
>> two sides and top, and to stay that way.
>>
>> A neat tip/trick on inset drawers is to plane a very small "rabbet" on
>> the bottom of the front edge of the drawer front. Make this small rabbet
>> equal in depth to the distance of your fitted gap around the top and two
>> sides. This way, your drawer, even though sitting flat on the runners,
>> will appear to have the same width gap all around.
>>
>> --www.eWoodShop.com
>> Last update: 4/15/2010
>> KarlCaillouet@ (the obvious)http://gplus.to/eWoodShop
>
> (or use Blum Metabox....g,d&r)
Damn those things are fugly...
--
www.ewoodshop.com
On Oct 22, 4:46=A0pm, Swingman <[email protected]> wrote:
> Robatoy <[email protected]> wrote:
> > On Oct 22, 2:36 pm, Swingman <[email protected]> wrote:
> >> On 10/22/2011 12:56 PM, Mike wrote:
>
> >>> I'm making my first project with drawers and discovered I am clueless=
as
> >>> to how much clearance is needed between the drawer face (the drawers =
are
> >>> inset) and the frame. I did a mock-up with 1/8 inch, but that seems w=
ay
> >>> too big and doesn't look good. The wood is quartered white oak. Any
> >>> enlightenment as to how much clearance is necessary will be appreciat=
ed.
>
> >>> Mike
>
> >> My preference is no more than 1/16th on inset drawers.
>
> >> Slides or runners?
>
> >> If the drawer is sitting on wooden runners, one of the problems with
> >> inset drawers is getting that bottom "gap" to equal the gap around the
> >> two sides and top, and to stay that way.
>
> >> A neat tip/trick on inset drawers is to plane a very small "rabbet" on
> >> the bottom of the front edge of the drawer front. Make this small rabb=
et
> >> equal in depth to the distance of your fitted gap around the top and t=
wo
> >> sides. This way, your drawer, even though sitting flat on the runners,
> >> will appear to have the same width gap all around.
>
> >> --www.eWoodShop.com
> >> Last update: 4/15/2010
> >> KarlCaillouet@ (the obvious)http://gplus.to/eWoodShop
>
> > (or use Blum Metabox....g,d&r)
>
> Damn those things are fugly...
> --www.ewoodshop.com
Yabbut...if you have their drill - and insert press, they're awesome
quick to built and install, and very reliable.
You can have your 1/16th or 1/32 all around and so easy to adjust.
Do they look nice? Well, with the new mottled silver and other shades,
plus the chrome side bars, it has some appeal to the 'euro-tech' fan.
I can knock off 12-16 drawers in a couple of hours... from scratch.
Oh, and they're finished too.
Nothing but upsides, 'cept the look... and even that's just fine with
the drawer closed *S*
The fact that all my drawers in the house are baltic birch should tell
you the rest.
On 10/23/2011 8:48 AM, Mike wrote:
> Thanks for the info guys.
>
> In answer to Swingman: Slides. I figured wooden runners would be a pain.
>
> Mike
Depends on the project. I wouldn't put then in a kitchen, but wooden
drawer runners are actually quite easy to do and a nice touch in
traditional furniture designs, particularly when using dovetail joinery
on the drawer (you don't have to hide part of the joinery with a side
mounted slide, or go to the trouble/fussiness of undermount drawer
slides, both in drawer design and installation).
There are many ways to do them, here are just a couple methods I've used
on projects:
http://e-woodshop.net/Projects3.htm
Scroll down to "A Few Wooden Drawer Slide Details"
--
www.eWoodShop.com
Last update: 4/15/2010
KarlCaillouet@ (the obvious)
http://gplus.to/eWoodShop
On 10/22/2011 2:10 PM, dpb wrote:
> On 10/22/2011 12:56 PM, Mike wrote:
>> I'm making my first project with drawers and discovered I am clueless as
>> to how much clearance is needed between the drawer face (the drawers are
>> inset) and the frame. I did a mock-up with 1/8 inch, but that seems way
>> too big and doesn't look good. The wood is quartered white oak. Any
>> enlightenment as to how much clearance is necessary will be appreciated.
>
> "Necessary" is a mil or so... :)
>
> Practically, I'll target a 32nd or 16th depending on how wide the drawer
> face crossgrain is (for plainsawn red oak in a file drawer height I'll
> go larger; w/ q-sawn white the smaller).
>
> --
>
Thanks. There's so much talk about seasonal changes in the wood I
wasn't sure how much would be necessary.
On 10/22/2011 12:56 PM, Mike wrote:
> I'm making my first project with drawers and discovered I am clueless as
> to how much clearance is needed between the drawer face (the drawers are
> inset) and the frame. I did a mock-up with 1/8 inch, but that seems way
> too big and doesn't look good. The wood is quartered white oak. Any
> enlightenment as to how much clearance is necessary will be appreciated.
"Necessary" is a mil or so... :)
Practically, I'll target a 32nd or 16th depending on how wide the drawer
face crossgrain is (for plainsawn red oak in a file drawer height I'll
go larger; w/ q-sawn white the smaller).
--
Mike wrote:
> I'm making my first project with drawers and discovered I am clueless
> as to how much clearance is needed between the drawer face (the
> drawers are inset) and the frame. I did a mock-up with 1/8 inch, but
> that seems way too big and doesn't look good. The wood is quartered
> white oak. Any enlightenment as to how much clearance is necessary
> will be appreciated.
> Mike
1/16 each side and you are safe unless you have really, *REALLY* deep
drawers).
If the drawer faces are horizontal, next to nothing clearance on the ends
works.
If you taper the drawer edges slightly inward, next to nothing all around
works.
--
dadiOH
____________________________
dadiOH's dandies v3.06...
...a help file of info about MP3s, recording from
LP/cassette and tips & tricks on this and that.
Get it at http://mysite.verizon.net/xico
On 10/22/2011 12:56 PM, Mike wrote:
> I'm making my first project with drawers and discovered I am clueless as
> to how much clearance is needed between the drawer face (the drawers are
> inset) and the frame. I did a mock-up with 1/8 inch, but that seems way
> too big and doesn't look good. The wood is quartered white oak. Any
> enlightenment as to how much clearance is necessary will be appreciated.
>
> Mike
My preference is no more than 1/16th on inset drawers.
Slides or runners?
If the drawer is sitting on wooden runners, one of the problems with
inset drawers is getting that bottom "gap" to equal the gap around the
two sides and top, and to stay that way.
A neat tip/trick on inset drawers is to plane a very small "rabbet" on
the bottom of the front edge of the drawer front. Make this small rabbet
equal in depth to the distance of your fitted gap around the top and two
sides. This way, your drawer, even though sitting flat on the runners,
will appear to have the same width gap all around.
--
www.eWoodShop.com
Last update: 4/15/2010
KarlCaillouet@ (the obvious)
http://gplus.to/eWoodShop
On 10/22/2011 12:56 PM, Mike wrote:
> I'm making my first project with drawers and discovered I am clueless as
> to how much clearance is needed between the drawer face (the drawers are
> inset) and the frame. I did a mock-up with 1/8 inch, but that seems way
> too big and doesn't look good. The wood is quartered white oak. Any
> enlightenment as to how much clearance is necessary will be appreciated.
>
> Mike
I typically cut the drawer front 1/8" shorter and narrower than the
opening. I end up with a 1/16" reveal on all sides.