I am making cubes of cocobolo, each face being approximately
2 inches by 2 inches. These are going to be "trump cubes"
for use in card games. On four of the faces, I want to
draw a picture of each of the four suits, a heart, a club,
a diamond, and a spade. I will either leave the remaining
two faces blank or write some simple words.
BTW, the cube serves no useful purpose in the play of the
game. It's merely sitting on the table looking pretty
and reminding people which suit is currently trump.
My question is: How should I best write and draw on cocobolo?
I could use red and black paint for the suits, but it seems
a shame to spoil the beauty of the wood. I'd rather have
something a bit more subtle. I've never done woodburning,
but I thought that might be a possibility?
Any suggestions welcomed. Thanks in advance,
--
Eric Sink
Consider laser engraving. You get a subtle image which is razor sharp.
I used laser engraving on the cover of a 3-ring presentation binder made
of mesquite. Contact me for a photo if interested in seeing it. Glenn
* Re: Our address...From a Scot ballad, circa 1350:
"Oh, my name is Little Jock Elliot, an' ( wha daur meddle wi' me?")
> I am making cubes of cocobolo, each face being approximately
> 2 inches by 2 inches. These are going to be "trump cubes"
> for use in card games. On four of the faces, I want to
> draw a picture of each of the four suits, a heart, a club,
> a diamond, and a spade. I will either leave the remaining
> two faces blank or write some simple words.
>
> BTW, the cube serves no useful purpose in the play of the
> game. It's merely sitting on the table looking pretty
> and reminding people which suit is currently trump.
>
> My question is: How should I best write and draw on cocobolo?
> I could use red and black paint for the suits, but it seems
> a shame to spoil the beauty of the wood. I'd rather have
> something a bit more subtle. I've never done woodburning,
> but I thought that might be a possibility?
>
> Any suggestions welcomed. Thanks in advance,
Woodburning is a good option, perhaps even woodcarving to carve out the
symbols. Its not uncommon to see some kind of sticker or paper image of the
symbol glued to the wood and then covered with an appropriate finish to
'seal' it in also.
--
Regards,
Dean Bielanowski
Editor,
Online Tool Reviews
http://www.onlinetoolreviews.com
------------------------------------------------------------
Latest 5 Reviews:
- Eze-Lap Diamond Sharpening Stones
- Incra TS-III Table Saw Fence
- Ryobi AP13 Planer/Thicknesser
- BeadLOCK Loose Tenon Joinery System
- Hyphone Air Tool Kit & Impact Wrench
------------------------------------------------------------
This is a good opportunity to learn marquetry......
Glenn
"Eric W. Sink" <[email protected]> wrote in message
news:[email protected]...
> I am making cubes of cocobolo, each face being approximately
> 2 inches by 2 inches. These are going to be "trump cubes"
> for use in card games. On four of the faces, I want to
> draw a picture of each of the four suits, a heart, a club,
> a diamond, and a spade. I will either leave the remaining
> two faces blank or write some simple words.
>
> BTW, the cube serves no useful purpose in the play of the
> game. It's merely sitting on the table looking pretty
> and reminding people which suit is currently trump.
>
> My question is: How should I best write and draw on cocobolo?
> I could use red and black paint for the suits, but it seems
> a shame to spoil the beauty of the wood. I'd rather have
> something a bit more subtle. I've never done woodburning,
> but I thought that might be a possibility?
>
> Any suggestions welcomed. Thanks in advance,
>
> --
> Eric Sink
O
>My question is: How should I best write and draw on cocobolo?
>I could use red and black paint for the suits, but it seems
>a shame to spoil the beauty of the wood. I'd rather have
>something a bit more subtle. I've never done woodburning,
>but I thought that might be a possibility?
black only shows so well on cocobolo if it gets at all dark.
--
Knight-Toolworks & Custom Planes
Custom made wooden planes at reasonable prices
See http://www.knight-toolworks.com For prices and ordering instructions.
Find someone that does laser carving, you should be able to send them a cube
and the idea and get the cube back for a reasonable cost.
"Eric W. Sink" <[email protected]> wrote in message
news:[email protected]...
> I am making cubes of cocobolo, each face being approximately
> 2 inches by 2 inches. These are going to be "trump cubes"
> for use in card games. On four of the faces, I want to
> draw a picture of each of the four suits, a heart, a club,
> a diamond, and a spade. I will either leave the remaining
> two faces blank or write some simple words.
>
> BTW, the cube serves no useful purpose in the play of the
> game. It's merely sitting on the table looking pretty
> and reminding people which suit is currently trump.
>
> My question is: How should I best write and draw on cocobolo?
> I could use red and black paint for the suits, but it seems
> a shame to spoil the beauty of the wood. I'd rather have
> something a bit more subtle. I've never done woodburning,
> but I thought that might be a possibility?
>
> Any suggestions welcomed. Thanks in advance,
>
> --
> Eric Sink
What about using a contrasting wood for the suites and cut them thin and
glue it on each face?
"Eric W. Sink" <[email protected]> wrote in message
news:[email protected]...
> I am making cubes of cocobolo, each face being approximately
> 2 inches by 2 inches. These are going to be "trump cubes"
> for use in card games. On four of the faces, I want to
> draw a picture of each of the four suits, a heart, a club,
> a diamond, and a spade. I will either leave the remaining
> two faces blank or write some simple words.
>
> BTW, the cube serves no useful purpose in the play of the
> game. It's merely sitting on the table looking pretty
> and reminding people which suit is currently trump.
>
> My question is: How should I best write and draw on cocobolo?
> I could use red and black paint for the suits, but it seems
> a shame to spoil the beauty of the wood. I'd rather have
> something a bit more subtle. I've never done woodburning,
> but I thought that might be a possibility?
>
> Any suggestions welcomed. Thanks in advance,
>
> --
> Eric Sink