I'm about to start making jigs and practicing new techniques (new to me,
that is) on scrap before I start making my end tables.
One of the things I'll need to do is to cut out the 1"x1" notches in the
mitered edges of these "frame" pieces
https://www.flickr.com/photos/gdguarino/16877714438/in/set-72157639547178715
The notches are to allow the tops of the legs to protrude through the
table top:
https://www.flickr.com/photos/gdguarino/16851937401/in/album-72157639547178715/
No table saw. No band saw. I have a jig saw, but that wouldn't be nearly
neat enough. So I figure to do them by hand. Any advice for a reasonably
priced saw that can cut a nice clean line?
In article <[email protected]>, Greg Guarino
<[email protected]> wrote:
> Any advice for a reasonably
> priced saw that can cut a nice clean line?
I really like this one:
<http://www.leevalley.com/en/Wood/page.aspx?p=32935&cat=1,42884,42898&ap
=1>
--
Splinters in my Fingers blog: <http://woodenwabbits.blogspot.com>
On Tue, 7 Apr 2015 17:05:21 -0700, "Lew Hodgett"
<[email protected]> wrote:
>Greg Guarino wrote:
>
>
>> I'm about to start making jigs and practicing new techniques (new to
>> me,
>> that is) on scrap before I start making my end tables.
>>
>> One of the things I'll need to do is to cut out the 1"x1" notches in
>> the
>> mitered edges of these "frame" pieces
>>
>> https://www.flickr.com/photos/gdguarino/16877714438/in/set-72157639547178715
>>
>>
>> The notches are to allow the tops of the legs to protrude through
>> the
>> table top:
>>
>> https://www.flickr.com/photos/gdguarino/16851937401/in/album-72157639547178715/
>>
>>
>> No table saw. No band saw. I have a jig saw, but that wouldn't be
>> nearly
>> neat enough. So I figure to do them by hand. Any advice for a
>> reasonably
>> priced saw that can cut a nice clean line?
>-------------------------------------------------------------------------
>Go to the Harbor Freight web site.
>
>http://tinyurl.com/5v3yu
>
>Search for "Hand Saw".
>
>Pick one of the flush cut pull saws for less than $10, buy one and
>practice on your scrap wood.
>
>For $10 max, you could even but two (2) and run your own
>comparison tests.
>
>You don't identify your jig saw but my Bosch 1587 with Bosch
>bi-metal blades still cuts a clean cut even after all these years.
>
1590EVS
Greg Guarino wrote:
> I'm about to start making jigs and practicing new techniques (new to
> me,
> that is) on scrap before I start making my end tables.
>
> One of the things I'll need to do is to cut out the 1"x1" notches in
> the
> mitered edges of these "frame" pieces
>
> https://www.flickr.com/photos/gdguarino/16877714438/in/set-72157639547178715
>
>
> The notches are to allow the tops of the legs to protrude through
> the
> table top:
>
> https://www.flickr.com/photos/gdguarino/16851937401/in/album-72157639547178715/
>
>
> No table saw. No band saw. I have a jig saw, but that wouldn't be
> nearly
> neat enough. So I figure to do them by hand. Any advice for a
> reasonably
> priced saw that can cut a nice clean line?
-------------------------------------------------------------------------
Go to the Harbor Freight web site.
http://tinyurl.com/5v3yu
Search for "Hand Saw".
Pick one of the flush cut pull saws for less than $10, buy one and
practice on your scrap wood.
For $10 max, you could even but two (2) and run your own
comparison tests.
You don't identify your jig saw but my Bosch 1587 with Bosch
bi-metal blades still cuts a clean cut even after all these years.
Lew
On Wednesday, April 8, 2015 at 11:33:01 AM UTC-4, Leon wrote:
> On 4/7/2015 6:33 PM, krw wrote:
> > On Tue, 07 Apr 2015 16:21:58 -0500, Leon <lcb11211@swbelldotnet>
> > wrote:
> >
> >> On 4/7/2015 2:45 PM, Greg Guarino wrote:
> >>> I'm about to start making jigs and practicing new techniques (new to me,
> >>> that is) on scrap before I start making my end tables.
> >>>
> >>> One of the things I'll need to do is to cut out the 1"x1" notches in the
> >>> mitered edges of these "frame" pieces
> >>>
> >>> https://www.flickr.com/photos/gdguarino/16877714438/in/set-72157639547178715
> >>>
> >>>
> >>> The notches are to allow the tops of the legs to protrude through the
> >>> table top:
> >>>
> >>> https://www.flickr.com/photos/gdguarino/16851937401/in/album-72157639547178715/
> >>>
> >>>
> >>> No table saw. No band saw. I have a jig saw, but that wouldn't be nearly
> >>> neat enough. So I figure to do them by hand. Any advice for a reasonably
> >>> priced saw that can cut a nice clean line?
> >>
> >>
> >> First off, what kind of jig saw do you have. My Milwaukee with Bosch
> >> blades give my TS a run for its money for smoothness.
> >
> > What, No Festool, Leon? I was shocked at what a difference a decent
> > saw makes. I bought a Bosch several years ago and it's been great (no
> > Festool here either ;-).
>
> LOL.. No I bought my last jig saw, the Milwaukee, about 15 years ago,
> before Festool was even on my radar. My Milwaukee was, at that time,
> built by the German company, AEG. Exactly like this one except red and
> silver.
> http://www.aeg-powertools.eu/woodworking/step-1200-bx/
> The sales guy steered me from the Bosch towards this one mostly because
> of the superior blade change set up. With a smooth cutting Bosch blade
> it leaves a burnished edge when cross cutting oak. In aggressive mode
> it will cut a 2x4 as quickly as a circular saw,
>
Just for fun, I tried to locate a local AEG dealer.
On the Store Locator page it says:
"Enter your street, town or postcode and country below to find your nearest stockist"
I entered my Zip Code followed by USA.
The Store Locator produced a Google map showing a location that is in the middle of our local airport, but an address that appears to be in Taiwan.
King Light Department Co., Ltd.
No. 226 Shin Ron Road
Tau Jou Village
Shin Woo, Taoyuan
Phone (0)3 490 31 86
Very Strange!
On 4/7/2015 6:33 PM, krw wrote:
> On Tue, 07 Apr 2015 16:21:58 -0500, Leon <lcb11211@swbelldotnet>
> wrote:
>
>> On 4/7/2015 2:45 PM, Greg Guarino wrote:
>>> I'm about to start making jigs and practicing new techniques (new to me,
>>> that is) on scrap before I start making my end tables.
>>>
>>> One of the things I'll need to do is to cut out the 1"x1" notches in the
>>> mitered edges of these "frame" pieces
>>>
>>> https://www.flickr.com/photos/gdguarino/16877714438/in/set-72157639547178715
>>>
>>>
>>> The notches are to allow the tops of the legs to protrude through the
>>> table top:
>>>
>>> https://www.flickr.com/photos/gdguarino/16851937401/in/album-72157639547178715/
>>>
>>>
>>> No table saw. No band saw. I have a jig saw, but that wouldn't be nearly
>>> neat enough. So I figure to do them by hand. Any advice for a reasonably
>>> priced saw that can cut a nice clean line?
>>
>>
>> First off, what kind of jig saw do you have. My Milwaukee with Bosch
>> blades give my TS a run for its money for smoothness.
>
> What, No Festool, Leon? I was shocked at what a difference a decent
> saw makes. I bought a Bosch several years ago and it's been great (no
> Festool here either ;-).
LOL.. No I bought my last jig saw, the Milwaukee, about 15 years ago,
before Festool was even on my radar. My Milwaukee was, at that time,
built by the German company, AEG. Exactly like this one except red and
silver.
http://www.aeg-powertools.eu/woodworking/step-1200-bx/
The sales guy steered me from the Bosch towards this one mostly because
of the superior blade change set up. With a smooth cutting Bosch blade
it leaves a burnished edge when cross cutting oak. In aggressive mode
it will cut a 2x4 as quickly as a circular saw,
>
>> Alternatively score your top with a utility knife or sharp chisel, hog
>> out most of the wood with your jig saw and then chisel the rest.
On 4/7/2015 4:30 PM, Greg Guarino wrote:
> Does anyone use a jigsaw with a fence?
I almost always use a small framers square as a fence for my Bosch, hand
held.
Key to a good cut, as usual, is a sharp blade and a well setup tool.
--
eWoodShop: www.eWoodShop.com
Wood Shop: www.e-WoodShop.net
https://www.google.com/+eWoodShop
https://plus.google.com/+KarlCaillouet/posts
http://www.custommade.com/by/ewoodshop/
KarlCaillouet@ (the obvious)
Greg Guarino <[email protected]> wrote in
news:[email protected]:
> No table saw. No band saw. I have a jig saw, but that wouldn't be
> nearly neat enough. So I figure to do them by hand. Any advice for a
> reasonably priced saw that can cut a nice clean line?
The Crown Tool saws aren't bad. They don't cut nearly as
well as a Lie-Nielson Independance saw, but they're also
a lot cheaper.
I'm going to guess the Veritas saw is also good, and still
cheaper than the L-N - if only it wasn't so god-awful ugly.
John
On 4/7/2015 5:21 PM, Leon wrote:
> On 4/7/2015 2:45 PM, Greg Guarino wrote:
>> I'm about to start making jigs and practicing new techniques (new to me,
>> that is) on scrap before I start making my end tables.
>>
>> One of the things I'll need to do is to cut out the 1"x1" notches in the
>> mitered edges of these "frame" pieces
>>
>> https://www.flickr.com/photos/gdguarino/16877714438/in/set-72157639547178715
>>
>>
>>
>> The notches are to allow the tops of the legs to protrude through the
>> table top:
>>
>> https://www.flickr.com/photos/gdguarino/16851937401/in/album-72157639547178715/
>>
>>
>>
>> No table saw. No band saw. I have a jig saw, but that wouldn't be nearly
>> neat enough. So I figure to do them by hand. Any advice for a reasonably
>> priced saw that can cut a nice clean line?
>
>
> First off, what kind of jig saw do you have. My Milwaukee with Bosch
> blades give my TS a run for its money for smoothness.
I have a couple, but the better one is a very old Black and Decker.
Probably '70s vintage. It has produced smoother cuts than I would have
expected on the rare times I have used it. Another experiment to try I
guess. Does anyone use a jigsaw with a fence?
Leon wrote:
>
> LOL.. No I bought my last jig saw, the Milwaukee, about 15 years ago,
> before Festool was even on my radar. My Milwaukee was, at that time,
> built by the German company, AEG. Exactly like this one except red
> and silver.
> http://www.aeg-powertools.eu/woodworking/step-1200-bx/
> The sales guy steered me from the Bosch towards this one mostly
> because of the superior blade change set up. With a smooth cutting
> Bosch blade it leaves a burnished edge when cross cutting oak. In
> aggressive mode it will cut a 2x4 as quickly as a circular saw,
>
>
Ok - you know I trust what you say Leon, but that last statement almost
tripped my Bullshit alarm. If it had not come from you, it certainly would
have. I can't imagine any jig saw that will cut as fast as a circular saw.
--
-Mike-
[email protected]
On Tue, 07 Apr 2015 15:45:10 -0400
Greg Guarino <[email protected]> wrote:
> No table saw. No band saw. I have a jig saw, but that wouldn't be
> nearly neat enough. So I figure to do them by hand. Any advice for a
> reasonably priced saw that can cut a nice clean line?
look at some of the work of paul sellers
he does a lot of work by hand
it'd be hard not to learn something from him
On 4/8/2015 11:06 AM, DerbyDad03 wrote:
> On Wednesday, April 8, 2015 at 11:33:01 AM UTC-4, Leon wrote:
>> On 4/7/2015 6:33 PM, krw wrote:
>>> On Tue, 07 Apr 2015 16:21:58 -0500, Leon <lcb11211@swbelldotnet>
>>> wrote:
>>>
>>>> On 4/7/2015 2:45 PM, Greg Guarino wrote:
>>>>> I'm about to start making jigs and practicing new techniques (new to me,
>>>>> that is) on scrap before I start making my end tables.
>>>>>
>>>>> One of the things I'll need to do is to cut out the 1"x1" notches in the
>>>>> mitered edges of these "frame" pieces
>>>>>
>>>>> https://www.flickr.com/photos/gdguarino/16877714438/in/set-72157639547178715
>>>>>
>>>>>
>>>>> The notches are to allow the tops of the legs to protrude through the
>>>>> table top:
>>>>>
>>>>> https://www.flickr.com/photos/gdguarino/16851937401/in/album-72157639547178715/
>>>>>
>>>>>
>>>>> No table saw. No band saw. I have a jig saw, but that wouldn't be nearly
>>>>> neat enough. So I figure to do them by hand. Any advice for a reasonably
>>>>> priced saw that can cut a nice clean line?
>>>>
>>>>
>>>> First off, what kind of jig saw do you have. My Milwaukee with Bosch
>>>> blades give my TS a run for its money for smoothness.
>>>
>>> What, No Festool, Leon? I was shocked at what a difference a decent
>>> saw makes. I bought a Bosch several years ago and it's been great (no
>>> Festool here either ;-).
>>
>> LOL.. No I bought my last jig saw, the Milwaukee, about 15 years ago,
>> before Festool was even on my radar. My Milwaukee was, at that time,
>> built by the German company, AEG. Exactly like this one except red and
>> silver.
>> http://www.aeg-powertools.eu/woodworking/step-1200-bx/
>> The sales guy steered me from the Bosch towards this one mostly because
>> of the superior blade change set up. With a smooth cutting Bosch blade
>> it leaves a burnished edge when cross cutting oak. In aggressive mode
>> it will cut a 2x4 as quickly as a circular saw,
>>
>
> Just for fun, I tried to locate a local AEG dealer.
>
> On the Store Locator page it says:
>
> "Enter your street, town or postcode and country below to find your nearest stockist"
>
> I entered my Zip Code followed by USA.
>
> The Store Locator produced a Google map showing a location that is in the middle of our local airport, but an address that appears to be in Taiwan.
>
> King Light Department Co., Ltd.
> No. 226 Shin Ron Road
> Tau Jou Village
> Shin Woo, Taoyuan
> Phone (0)3 490 31 86
>
> Very Strange!
>
You might might find their tools here at all. IIRC they were building
drills and tools for NASA 15~20 years ago.
But they are located in Winnenden, Germany
http://www.aeg-powertools.eu/header/contact-us/
On 4/7/2015 2:45 PM, Greg Guarino wrote:
> I'm about to start making jigs and practicing new techniques (new to me,
> that is) on scrap before I start making my end tables.
>
> One of the things I'll need to do is to cut out the 1"x1" notches in the
> mitered edges of these "frame" pieces
>
> https://www.flickr.com/photos/gdguarino/16877714438/in/set-72157639547178715
>
>
> The notches are to allow the tops of the legs to protrude through the
> table top:
>
> https://www.flickr.com/photos/gdguarino/16851937401/in/album-72157639547178715/
>
>
> No table saw. No band saw. I have a jig saw, but that wouldn't be nearly
> neat enough. So I figure to do them by hand. Any advice for a reasonably
> priced saw that can cut a nice clean line?
First off, what kind of jig saw do you have. My Milwaukee with Bosch
blades give my TS a run for its money for smoothness.
Alternatively score your top with a utility knife or sharp chisel, hog
out most of the wood with your jig saw and then chisel the rest.
On Tue, 07 Apr 2015 16:21:58 -0500, Leon <lcb11211@swbelldotnet>
wrote:
>On 4/7/2015 2:45 PM, Greg Guarino wrote:
>> I'm about to start making jigs and practicing new techniques (new to me,
>> that is) on scrap before I start making my end tables.
>>
>> One of the things I'll need to do is to cut out the 1"x1" notches in the
>> mitered edges of these "frame" pieces
>>
>> https://www.flickr.com/photos/gdguarino/16877714438/in/set-72157639547178715
>>
>>
>> The notches are to allow the tops of the legs to protrude through the
>> table top:
>>
>> https://www.flickr.com/photos/gdguarino/16851937401/in/album-72157639547178715/
>>
>>
>> No table saw. No band saw. I have a jig saw, but that wouldn't be nearly
>> neat enough. So I figure to do them by hand. Any advice for a reasonably
>> priced saw that can cut a nice clean line?
>
>
>First off, what kind of jig saw do you have. My Milwaukee with Bosch
>blades give my TS a run for its money for smoothness.
What, No Festool, Leon? I was shocked at what a difference a decent
saw makes. I bought a Bosch several years ago and it's been great (no
Festool here either ;-).
>Alternatively score your top with a utility knife or sharp chisel, hog
>out most of the wood with your jig saw and then chisel the rest.