Hi everyone,
I just finished installing the Veritas twin-screw vise on my workbench (an
exact copy of Sam Allen's joiner's bench from his workbench book) and
thought I'd write up my experience.
Things went fairly smoothly, but not without some hiccups.
First, the instructions are quite detailed and as many of you might have
heard before, the warning on the front page to not deviate from the
instructions are wise and I followed them for the most part. Also, the
materials for the vise were MOSTLY of very high quality, especially the
screws themselves, which I feel is the most important thing. All the parts
were there (which is good, since I bought this about 3 months ago), so I was
set to go.
I used hard maple for the jaws, and made them up at 2" thick, 7" tall, and
24" wide (the width of my bench). It was important to figure out the
minimum height of the jaws to accomodate the bench thickness and hardware,
but the instructions made this clear and not difficult. The next step was
to figure out the screw spacing and to adjust the length of the bicycle
chain. I used 14 5/8", so I had to remove 6 links from the chain. The
instructions say to file the pins down, but I found this to be extremely
slow going, so I used my bench grinder, which worked fine. I did have to
use a center punch to drive the pins out, which took a little more effort
than the instructions made it out to be. Also, the link supplied with the
chain to connect the two ends had the spring-clip alread attached. I don't
really see why Lee Valley sent it this way, and I would have rather had it
separate so as to avoid having to screw with the clip, and possibly bending
it (which I did slightly) removing it from the link pins.
Once the chain was set, the next step was laying out and drilling holes
through the jaws for the screws and other parts. I took my time here, and
was glad because everything went together fine the first try. I won't
really get into this except to say that having a good drill press with a
large stroke was a big advantage. Also, a few steps here could've contained
some more hints regarding placement of clamps, etc. I had to reposition my
clamps a few times to get clearance on my drill press. Also, the
instructions have you install the screw nuts onto the rear jaws before
drilling the bolt mounting holes. This didn't make much sense, because you
have to drill counterbores in the inside face of the rear jaw, so you have
to take the nuts off to lay the jaw flat on the drill press table.
After the holes were drilled through the faces of the jaws, and the mounting
holes for the rear jaw were in place, it was necessary to transfer the holes
to the end of the bench in order to drill for the rear jaw mounting bolts.
The rear jaw is attached with barrel bolts placed in cross-drilled holes
from the bottom of the bench. I found it pretty tricky to get the rear jaw
in position, but ended up clamping it across the width of the bench, across
the seam where the bench and rear jaw met. The idea was to have a small
amount of the rear jaw above the bench surface, so you can plane it down
even after you install it. Anyway, it worked out alright. The next step
was to drill the crossing holes for the barell bolts. Since my bench was
already constructed, I had to lay on the floor to do this, which could've
been more comfortable. If you have the opportunity to install this to your
benchtop with the top upside down on some supports, I would recommend it,
not only for comfort, but for the increased accuracy you're sure to have. I
made the jig for locating the crossing holes, but I got one wrong slightly
and had to drill an overlapping hole. It didn't seem to affect the mounting
of the rear jaw at all. One more caveat here, the instructions say to put
some crumpled paper in the hole for the barrel bolts to act as a spring in
aligning them with the bolts. Perhaps it was assumed that the benchtop
would be upside down, but I found this to be more of a hassle than a
benefit.
So, now the rear jaw was installed after quite a bit of effort (at least
that's what my back was telling me). Next was the front jaw. In order to
install this, I had to drill clearance holes through the upper end cross
braces of my bench base. Because I had already mounted the rear jaw, this
meant drilling from the inside of the base outward (or removing the rear
jaw, which I wasn't going to do). Let's just say that laying contorted on
the floor, holding a cordless drill and drilling 1.5" holes through 1.5"
wood is not fun. Happily, I got the holes lined up just right the first
try.
After that, the screws are installed, with the chain in place, and screwed
in by hand until they are holding the front jaw in place against the rear
jaw. After aligning the tops and sides of the jaws, the thrust plates are
attached with lag bolts and washers. This is where my first real gripe with
the vise hardware comes up. The instructions DO say to not overtighten the
bolts, so I guess I should've been warned. Even so, I managed to break the
head off one of the bolts! I was ticked off, because I had read the
instructions and was consciously not using very much force. I was getting a
firm fit, to be sure, but "overtight"? I don't think so. So, my question to
Lee Valley is, why don't you include better bolts that aren't made of cheap
material? In fact, I think you should include the BEST bolts that you can
find. I'm not sure how the lack of one of the bolts on the thrust plate
will have in the long run, but it seemed to be holding, so I proceeded
ahead. If anyone has any insight here, it would be appreciated.
Another gripe I have is that there weren't any instructions on how to get
the vise handles to line up parallel to each other. I tried to install the
chain so that they would be that way, but by the time I had hand tightened
the screws up to the front jaw, and tightened them down in order to install
the thrust plates, they had become out of alignment. I couldn't figure out
any way to adjust them, so hopefully Robin Lee is reading this and can expla
in how this is done. I know I've seen many pictures of the vise on benches
with the handles perfectly parallel, so it must be possible. I'm sure
everyone that installs the vise would want their handles aligned, so why
there isn't instructions regarding this I really don't understand.
Ok, now that the jaws were installed, the cover was ready to go on. The
cover consists of two half-round end caps and a center aluminum section.
Because I had shorted the chain and had a smaller screw separation, I had to
shorten the cover in order for it to fit between the screw mechanisms. The
instructions say that a hacksaw can be used, and that's true and what I did.
All I can say is, I'm not that proficient at cutting curved pieces of metal
in straight lines with the hacksaw. I did have the idea (probably not
novel, I'm sure) of making shallow cuts on either side of the cover, and
then cutting down to the face on both sides at the same time, so at least I
ended up with a fairly straight edge. Overall, however I was pretty
frustrated by this. I didn't realize how fragile the finish on the cover
was, and the initial hacksawing I did was with it held by hand on the bench
top. This resulted in a very scratched finish, which pretty much sucks. I
wish the instructions would have warned me about this. Even more, however, I
wish Lee Valley would just have a question when you order the vise as to the
size of the cover you need and have it precut for you. For the price of the
vise, I think this is a reasonable request. At any rate, I got the cover in
place, albeit pretty well scratched up.
So, the final chapter (I didn't realize how long winded this was going to
be) was installing the handles. I only mention this because I ran into
another example of cheap hardware. The screws provided to attach the handle
end caps to the handles were square drive #8 1-1/4" (maybe 1-1/2"?) wood
screws. I drilled pilot holes were the instructions, and set my drill's
adjustable torque to 10 (out of 20), which considering the handles are
hardwood, should have been fine. Well, as you might have guessed, I broke
the head off one of the screws. Luckily I have a supply of panhead coarse
thread pocket hole screws, and one of these worked fine to replace the
broken screw. But, it just illustrates the point that some of the hardware
was not of the best quality in the kit.
I did put the vise through it's paces briefly after the install was finished
and I have to say that the vise is GREAT! I was extremely impressed with
how much clamping force I could generate. I tried holding a big panel in
place with bench dogs across the full vise width, and it worked wonderfully.
I also clamped a 10" wide board vertically in the vise (as if to cut
dovetails or something), and it also worked just as I had hoped. I can't
wait to actually use it on my upcoming projects.
So, in summary, I will have to give the vise a score of maybe 8.5/10, due to
the small issues I have with some of the components. I admit that the
problems could have been avoided, but I feel I was using a reasonable amount
of caution and just got stuck by having a few bad parts. I just hope the
lack of one of the thrust plate bolts doesn't mess me up in the future.
I hope this has been useful for anyone considering this vise. I would
definitely buy it again, so that might be the most telling thing of all.
Mike
On Mon, 17 Nov 2003 04:15:39 GMT, "Mike in Mystic"
<[email protected]> wrote:
How about posting some pics in alt.binaries.pictures.woodworking for
us to see. I am especially interested in the twin-screw vise and your
workbench. I will be making them in spring.
Thanks
>Hi everyone,
>
>I just finished installing the Veritas twin-screw vise on my workbench (an
>exact copy of Sam Allen's joiner's bench from his workbench book) and
>thought I'd write up my experience.
>
>Things went fairly smoothly, but not without some hiccups.
>
>First, the instructions are quite detailed and as many of you might have
>heard before, the warning on the front page to not deviate from the
>instructions are wise and I followed them for the most part. Also, the
>materials for the vise were MOSTLY of very high quality, especially the
>screws themselves, which I feel is the most important thing. All the parts
>were there (which is good, since I bought this about 3 months ago), so I was
>set to go.
>
>I used hard maple for the jaws, and made them up at 2" thick, 7" tall, and
>24" wide (the width of my bench). It was important to figure out the
>minimum height of the jaws to accomodate the bench thickness and hardware,
>but the instructions made this clear and not difficult. The next step was
>to figure out the screw spacing and to adjust the length of the bicycle
>chain. I used 14 5/8", so I had to remove 6 links from the chain. The
>instructions say to file the pins down, but I found this to be extremely
>slow going, so I used my bench grinder, which worked fine. I did have to
>use a center punch to drive the pins out, which took a little more effort
>than the instructions made it out to be. Also, the link supplied with the
>chain to connect the two ends had the spring-clip alread attached. I don't
>really see why Lee Valley sent it this way, and I would have rather had it
>separate so as to avoid having to screw with the clip, and possibly bending
>it (which I did slightly) removing it from the link pins.
>
>Once the chain was set, the next step was laying out and drilling holes
>through the jaws for the screws and other parts. I took my time here, and
>was glad because everything went together fine the first try. I won't
>really get into this except to say that having a good drill press with a
>large stroke was a big advantage. Also, a few steps here could've contained
>some more hints regarding placement of clamps, etc. I had to reposition my
>clamps a few times to get clearance on my drill press. Also, the
>instructions have you install the screw nuts onto the rear jaws before
>drilling the bolt mounting holes. This didn't make much sense, because you
>have to drill counterbores in the inside face of the rear jaw, so you have
>to take the nuts off to lay the jaw flat on the drill press table.
>
>After the holes were drilled through the faces of the jaws, and the mounting
>holes for the rear jaw were in place, it was necessary to transfer the holes
>to the end of the bench in order to drill for the rear jaw mounting bolts.
>The rear jaw is attached with barrel bolts placed in cross-drilled holes
>from the bottom of the bench. I found it pretty tricky to get the rear jaw
>in position, but ended up clamping it across the width of the bench, across
>the seam where the bench and rear jaw met. The idea was to have a small
>amount of the rear jaw above the bench surface, so you can plane it down
>even after you install it. Anyway, it worked out alright. The next step
>was to drill the crossing holes for the barell bolts. Since my bench was
>already constructed, I had to lay on the floor to do this, which could've
>been more comfortable. If you have the opportunity to install this to your
>benchtop with the top upside down on some supports, I would recommend it,
>not only for comfort, but for the increased accuracy you're sure to have. I
>made the jig for locating the crossing holes, but I got one wrong slightly
>and had to drill an overlapping hole. It didn't seem to affect the mounting
>of the rear jaw at all. One more caveat here, the instructions say to put
>some crumpled paper in the hole for the barrel bolts to act as a spring in
>aligning them with the bolts. Perhaps it was assumed that the benchtop
>would be upside down, but I found this to be more of a hassle than a
>benefit.
>
>So, now the rear jaw was installed after quite a bit of effort (at least
>that's what my back was telling me). Next was the front jaw. In order to
>install this, I had to drill clearance holes through the upper end cross
>braces of my bench base. Because I had already mounted the rear jaw, this
>meant drilling from the inside of the base outward (or removing the rear
>jaw, which I wasn't going to do). Let's just say that laying contorted on
>the floor, holding a cordless drill and drilling 1.5" holes through 1.5"
>wood is not fun. Happily, I got the holes lined up just right the first
>try.
>
>After that, the screws are installed, with the chain in place, and screwed
>in by hand until they are holding the front jaw in place against the rear
>jaw. After aligning the tops and sides of the jaws, the thrust plates are
>attached with lag bolts and washers. This is where my first real gripe with
>the vise hardware comes up. The instructions DO say to not overtighten the
>bolts, so I guess I should've been warned. Even so, I managed to break the
>head off one of the bolts! I was ticked off, because I had read the
>instructions and was consciously not using very much force. I was getting a
>firm fit, to be sure, but "overtight"? I don't think so. So, my question to
>Lee Valley is, why don't you include better bolts that aren't made of cheap
>material? In fact, I think you should include the BEST bolts that you can
>find. I'm not sure how the lack of one of the bolts on the thrust plate
>will have in the long run, but it seemed to be holding, so I proceeded
>ahead. If anyone has any insight here, it would be appreciated.
>
>Another gripe I have is that there weren't any instructions on how to get
>the vise handles to line up parallel to each other. I tried to install the
>chain so that they would be that way, but by the time I had hand tightened
>the screws up to the front jaw, and tightened them down in order to install
>the thrust plates, they had become out of alignment. I couldn't figure out
>any way to adjust them, so hopefully Robin Lee is reading this and can expla
>in how this is done. I know I've seen many pictures of the vise on benches
>with the handles perfectly parallel, so it must be possible. I'm sure
>everyone that installs the vise would want their handles aligned, so why
>there isn't instructions regarding this I really don't understand.
>
>Ok, now that the jaws were installed, the cover was ready to go on. The
>cover consists of two half-round end caps and a center aluminum section.
>Because I had shorted the chain and had a smaller screw separation, I had to
>shorten the cover in order for it to fit between the screw mechanisms. The
>instructions say that a hacksaw can be used, and that's true and what I did.
>All I can say is, I'm not that proficient at cutting curved pieces of metal
>in straight lines with the hacksaw. I did have the idea (probably not
>novel, I'm sure) of making shallow cuts on either side of the cover, and
>then cutting down to the face on both sides at the same time, so at least I
>ended up with a fairly straight edge. Overall, however I was pretty
>frustrated by this. I didn't realize how fragile the finish on the cover
>was, and the initial hacksawing I did was with it held by hand on the bench
>top. This resulted in a very scratched finish, which pretty much sucks. I
>wish the instructions would have warned me about this. Even more, however, I
>wish Lee Valley would just have a question when you order the vise as to the
>size of the cover you need and have it precut for you. For the price of the
>vise, I think this is a reasonable request. At any rate, I got the cover in
>place, albeit pretty well scratched up.
>
>So, the final chapter (I didn't realize how long winded this was going to
>be) was installing the handles. I only mention this because I ran into
>another example of cheap hardware. The screws provided to attach the handle
>end caps to the handles were square drive #8 1-1/4" (maybe 1-1/2"?) wood
>screws. I drilled pilot holes were the instructions, and set my drill's
>adjustable torque to 10 (out of 20), which considering the handles are
>hardwood, should have been fine. Well, as you might have guessed, I broke
>the head off one of the screws. Luckily I have a supply of panhead coarse
>thread pocket hole screws, and one of these worked fine to replace the
>broken screw. But, it just illustrates the point that some of the hardware
>was not of the best quality in the kit.
>
>I did put the vise through it's paces briefly after the install was finished
>and I have to say that the vise is GREAT! I was extremely impressed with
>how much clamping force I could generate. I tried holding a big panel in
>place with bench dogs across the full vise width, and it worked wonderfully.
>I also clamped a 10" wide board vertically in the vise (as if to cut
>dovetails or something), and it also worked just as I had hoped. I can't
>wait to actually use it on my upcoming projects.
>
>So, in summary, I will have to give the vise a score of maybe 8.5/10, due to
>the small issues I have with some of the components. I admit that the
>problems could have been avoided, but I feel I was using a reasonable amount
>of caution and just got stuck by having a few bad parts. I just hope the
>lack of one of the thrust plate bolts doesn't mess me up in the future.
>
>I hope this has been useful for anyone considering this vise. I would
>definitely buy it again, so that might be the most telling thing of all.
>
>Mike
>
-----= Posted via Newsfeeds.Com, Uncensored Usenet News =-----
http://www.newsfeeds.com - The #1 Newsgroup Service in the World!
-----== Over 100,000 Newsgroups - 19 Different Servers! =-----
Mike -
I'll take a bow on behalf of the designer who sent back a detailed response
almost as long as your original post - few of the comments (in this case)
were mine .... :)
As for the aligned handles on the website - that's probably Murphy's work...
if a "random" event could take place which would suggest a design feature -
it'll happen in photography. We'll make a note of it.... Then too, it's
possible that the nut on one screw was fixed after handle alignment, or
shimmed out of a recess... rotating the nut should provide 90 degrees of
adjustment, with finer adjustment (less than 90) coming from shims....
Chain cover - offer stands.... the kit includes end caps (which you don't
need)...the cut extrusion won't cost us too much - and we'll put it in with
your next order....I can try and do it today- but your order's probably
packed and in the truck by now....
The shares'll have to wait for at least one more generation - not happening
this one!
Cheers -
Rob Lee
"Mike in Mystic" <[email protected]> wrote in message
news:[email protected]...
> Rob,
>
> Thanks very much for the detailed response. As always, the level of
> interaction you have with your customers is exceptional.
>
> A few notes regarding the comments you provided:
>
> 1) Regarding the installation of the barrel nuts in for the rear jaw
> mounting bolts. I found it quite easy to simply use a screw driver in the
> slot on the bottom of the nut and hold in lower than the bolt position. I
> had a small flashlight on the ground illuminating the area, so I could see
> the protruding bolt end, and then by pushing the bolt against the nut, I
> could simply slowly raise the nut and feel the bolt slide into the tapered
> recess. It actually wasn't that hard, other than having to lay on the
floor
> hehe. When I had the paper in the hole, I found that the spring back
effect
> actually made it harder to make small changes in height to the nut
position.
>
> 2) Regarding the alignment of the two screw handles. In your website
> picture you show the handles perfectly aligned and parallel. Is this only
> achieved because you may have used the maximum spacing? I knew enough not
> to assume that they would automatcially come out that way, but I didn't
see
> any mention of the alignment being a contraint of the system. I can think
> of at least one situation where having the handles aligned would be
> necessary - if you have a bank of drawers or a cabinet door opening at the
> end of the bench. Having both handles horizontal would be needed to open
> these. I admit I haven't seen this too much, but it's a thought. I guess
I
> will have to live with the handles as they came out.
>
> 3). Regarding the chain cover. I agree with you that the scratching of
the
> finish was my goof. I won't ask for a replacement. If it bothers me too
> much in the future I'll just buy one of your cover kits. Thanks for the
> offer, though. As for being overkill to warn against scratching the
cover,
> I don't think that's the case. You already warn against deforming it in
the
> hacksawing process, so adding a line "deforming and/or marring the finish"
> doesn't seem too big a deal. Since this is the part of the vise that
bears
> your logo and is the most visible part of the vise (other than the
handles,
> I suppose), it would be good to have customers avoid the bonehead result
> that I managed to do to my vise.
>
> 4) My wife says I've spent so much money at your website that I should
own
> stock in the company. Any plans to go public?? :)
>
>
> I really do appreciate the responsiveness you gave me and the obvious
> attention to even the smallest customer concerns that you have. I already
> placed another order at your website yesterday, so obviously you aren't
> going to lose my patronage.
>
> Best regards,
>
> Mike Logman
>
> --
>
> There are no stupid questions.
> There are a LOT of inquisitive idiots.
>
>
> "Robin Lee" <[email protected]> wrote in message
Hi -
Answers to your comments are interspersed below! (cut and pasted from the
comments I received from our R&D group- note that there's always a bit of a
"defensive" slant to a designer's response :) Many of your comments and
suggestions may help others in the future!
Cheers -
Rob Lee
"Mike in Mystic" <[email protected]> wrote in message
news:[email protected]...
> Hi everyone,
>
> I just finished installing the Veritas twin-screw vise on my workbench (an
> exact copy of Sam Allen's joiner's bench from his workbench book) and
> thought I'd write up my experience.
>
> Things went fairly smoothly, but not without some hiccups.
>
> First, the instructions are quite detailed and as many of you might have
> heard before, the warning on the front page to not deviate from the
> instructions are wise and I followed them for the most part. Also, the
> materials for the vise were MOSTLY of very high quality, especially the
> screws themselves, which I feel is the most important thing. All the
parts
> were there (which is good, since I bought this about 3 months ago), so I
was
> set to go.
>
> I used hard maple for the jaws, and made them up at 2" thick, 7" tall, and
> 24" wide (the width of my bench). It was important to figure out the
> minimum height of the jaws to accomodate the bench thickness and hardware,
> but the instructions made this clear and not difficult. The next step was
> to figure out the screw spacing and to adjust the length of the bicycle
> chain. I used 14 5/8", so I had to remove 6 links from the chain. The
> instructions say to file the pins down, but I found this to be extremely
> slow going, so I used my bench grinder, which worked fine. I did have to
> use a center punch to drive the pins out, which took a little more effort
> than the instructions made it out to be. Also, the link supplied with the
> chain to connect the two ends had the spring-clip alread attached. I
don't
> really see why Lee Valley sent it this way, and I would have rather had it
> separate so as to avoid having to screw with the clip, and possibly
bending
> it (which I did slightly) removing it from the link pins.
They are packaged this way to help prevent loss - since they are very small
on their own.
> Once the chain was set, the next step was laying out and drilling holes
> through the jaws for the screws and other parts. I took my time here, and
> was glad because everything went together fine the first try. I won't
> really get into this except to say that having a good drill press with a
> large stroke was a big advantage. Also, a few steps here could've
contained
> some more hints regarding placement of clamps, etc.
Throughout the intructions, hints are given in most cases where they apply
to all or most users - but there are so many different ways to clamp and
drill, it would be a bit like chasing one's tail to try and anticipate all
possible scenarios and provide hints for them. Every woodworker knows their
own shop and equipment best.
>I had to reposition my
> clamps a few times to get clearance on my drill press. Also, the
> instructions have you install the screw nuts onto the rear jaws before
> drilling the bolt mounting holes. This didn't make much sense, because
you
> have to drill counterbores in the inside face of the rear jaw, so you have
> to take the nuts off to lay the jaw flat on the drill press table.
It's quite true that the process would be a bit simpler in this customer's
case to install the nuts after the rear jaw in is place. But since there are
three different methods to attach the rear jaw outlined, the instructions
would be considerably more complicated to achieve the same end result.
Ordering the instructions in this way would only mean the user could avoid
using a couple of spacer blocks under the jaw when drilling the bolt holes.
>
> After the holes were drilled through the faces of the jaws, and the
mounting
> holes for the rear jaw were in place, it was necessary to transfer the
holes
> to the end of the bench in order to drill for the rear jaw mounting bolts.
> The rear jaw is attached with barrel bolts placed in cross-drilled holes
> from the bottom of the bench. I found it pretty tricky to get the rear
jaw
> in position, but ended up clamping it across the width of the bench,
across
> the seam where the bench and rear jaw met.
There is a very simple method that could be used to clamp the rear jaw in
position - as used by our own bench assemblers. The instructions could be
changed to add this tip. (RL note - will see that this gets added...)
> The idea was to have a small
> amount of the rear jaw above the bench surface, so you can plane it down
> even after you install it. Anyway, it worked out alright. The next step
> was to drill the crossing holes for the barell bolts. Since my bench was
> already constructed, I had to lay on the floor to do this, which could've
> been more comfortable. If you have the opportunity to install this to
your
> benchtop with the top upside down on some supports, I would recommend it,
> not only for comfort, but for the increased accuracy you're sure to have.
The instructions don't tell the customer not to flip the benchtop uspide
down but don't suggest it either. This could be another tip to add so long
as we also provide a caution about getting help and not wrecking one's back.
> I made the jig for locating the crossing holes, but I got one wrong
slightly
> and had to drill an overlapping hole. It didn't seem to affect the
mounting
> of the rear jaw at all. One more caveat here, the instructions say to put
> some crumpled paper in the hole for the barrel bolts to act as a spring in
> aligning them with the bolts. Perhaps it was assumed that the benchtop
> would be upside down, but I found this to be more of a hassle than a
> benefit.
This tip works in both orientations. The hole for the dowel nut will almost
always be deeper than it really needs to be. If the top is upseide down,
then the nuts can be pushed against the paper until they are lined up and
then they sit there until the bolt coes through to engage them. If right
side up, the user nees to hold the nuts in place with a nail or a dowel or
something. The paper then gives something to push against intead of
essentially having to hold the nut in exactly the right position in mid-air;
which I can say from experience is not easy. I didn't come up with this tip
but I have installed these nuts both ways and found the tip to be quite
useful.
> So, now the rear jaw was installed after quite a bit of effort (at least
> that's what my back was telling me). Next was the front jaw. In order to
> install this, I had to drill clearance holes through the upper end cross
> braces of my bench base. Because I had already mounted the rear jaw, this
> meant drilling from the inside of the base outward (or removing the rear
> jaw, which I wasn't going to do). Let's just say that laying contorted on
> the floor, holding a cordless drill and drilling 1.5" holes through 1.5"
> wood is not fun. Happily, I got the holes lined up just right the first
> try.
I checked Sam Allen's book and it is shown in a diagram (p. 32) to drill the
upper cross brace for screw clearance with the Veritas twin screw vise. In
my view, this should not be recommended. It is, as the customer found,
difficult to do and it would probably significantly weaken the structural
member in question. Perhaps we should include a caution in the catalogue
copy and the instructions that the vise should be installed only a bench
with adequate overhang or otherwise with clearance for the screws where it
needs to be.
>
> After that, the screws are installed, with the chain in place, and screwed
> in by hand until they are holding the front jaw in place against the rear
> jaw. After aligning the tops and sides of the jaws, the thrust plates are
> attached with lag bolts and washers. This is where my first real gripe
with
> the vise hardware comes up. The instructions DO say to not overtighten
the
> bolts, so I guess I should've been warned. Even so, I managed to break
the
> head off one of the bolts! I was ticked off, because I had read the
> instructions and was consciously not using very much force. I was getting
a
> firm fit, to be sure, but "overtight"? I don't think so. So, my question
to
> Lee Valley is, why don't you include better bolts that aren't made of
cheap
> material?
RL - we'll test a bunch of bolts - but this could be an isolated
problem...though I've snapped the heads off lag bolts (used in cedar!)
before...
> In fact, I think you should include the BEST bolts that you can
> find. I'm not sure how the lack of one of the bolts on the thrust plate
> will have in the long run, but it seemed to be holding, so I proceeded
> ahead. If anyone has any insight here, it would be appreciated.
The designer assures me that this will not be a problem....
> Another gripe I have is that there weren't any instructions on how to get
> the vise handles to line up parallel to each other. I tried to install
the
> chain so that they would be that way, but by the time I had hand tightened
> the screws up to the front jaw, and tightened them down in order to
install
> the thrust plates, they had become out of alignment. I couldn't figure
out
> any way to adjust them, so hopefully Robin Lee is reading this and can
expla
> in how this is done.
The alignment of the handles to each other is a function of the orientation
of each "Tee" in relation to the screw it's connected to and cannot be
changed. The product has always had this constraint. It may or may not be
made to be aligned but this would certainly add cost and complexity. (RL -
while aesthetically pleasing to some, I'd actually prefer them to be at 90
degrees to each other....)
>I know I've seen many pictures of the vise on benches
> with the handles perfectly parallel, so it must be possible. I'm sure
> everyone that installs the vise would want their handles aligned, so why
> there isn't instructions regarding this I really don't understand.
>
> Ok, now that the jaws were installed, the cover was ready to go on. The
> cover consists of two half-round end caps and a center aluminum section.
> Because I had shorted the chain and had a smaller screw separation, I had
to
> shorten the cover in order for it to fit between the screw mechanisms.
The
> instructions say that a hacksaw can be used, and that's true and what I
did.
> All I can say is, I'm not that proficient at cutting curved pieces of
metal
> in straight lines with the hacksaw. I did have the idea (probably not
> novel, I'm sure) of making shallow cuts on either side of the cover, and
> then cutting down to the face on both sides at the same time, so at least
I
> ended up with a fairly straight edge. Overall, however I was pretty
> frustrated by this. I didn't realize how fragile the finish on the cover
> was, and the initial hacksawing I did was with it held by hand on the
bench
> top. This resulted in a very scratched finish, which pretty much sucks.
I
> wish the instructions would have warned me about this.
RL - Mike - We'd be glad to cut and send you another one (it'll bug you
forever)...but, in all fairness, that's your goof !! Just email me your
address, and the length.... we'll add a note to the instructions too, but
it's overkill.....
> Even more, however, I
> wish Lee Valley would just have a question when you order the vise as to
the
> size of the cover you need and have it precut for you. For the price of
the
> vise, I think this is a reasonable request. At any rate, I got the cover
in
> place, albeit pretty well scratched up.
RL - the other choice would be to say the vise is 24" wide - change it your
own risk...:) Again - I understand what you're saying, but it would be
costly, and impractical to do. Significant numers of these vises are sold in
retail locations. The design of the endcaps does provide for some amount of
overlap to cover an irregular cut...
> So, the final chapter (I didn't realize how long winded this was going to
> be) was installing the handles. I only mention this because I ran into
> another example of cheap hardware. The screws provided to attach the
handle
> end caps to the handles were square drive #8 1-1/4" (maybe 1-1/2"?) wood
> screws. I drilled pilot holes were the instructions, and set my drill's
> adjustable torque to 10 (out of 20), which considering the handles are
> hardwood, should have been fine. Well, as you might have guessed, I broke
> the head off one of the screws. Luckily I have a supply of panhead coarse
> thread pocket hole screws, and one of these worked fine to replace the
> broken screw. But, it just illustrates the point that some of the
hardware
> was not of the best quality in the kit.
Again - we'll have a look...
> I did put the vise through it's paces briefly after the install was
finished
> and I have to say that the vise is GREAT! I was extremely impressed with
> how much clamping force I could generate. I tried holding a big panel in
> place with bench dogs across the full vise width, and it worked
wonderfully.
> I also clamped a 10" wide board vertically in the vise (as if to cut
> dovetails or something), and it also worked just as I had hoped. I can't
> wait to actually use it on my upcoming projects.
>
> So, in summary, I will have to give the vise a score of maybe 8.5/10, due
to
> the small issues I have with some of the components. I admit that the
> problems could have been avoided, but I feel I was using a reasonable
amount
> of caution and just got stuck by having a few bad parts. I just hope the
> lack of one of the thrust plate bolts doesn't mess me up in the future.
>
> I hope this has been useful for anyone considering this vise. I would
> definitely buy it again, so that might be the most telling thing of all.
Thanks too, for the comments....every time we get suggestions, it's an
opportunity to improve...
Cheers -
Rob Lee
> Mike
>
>
I plan on doing that, I just forgot to bring the camera outside with me. I
actually was going to photo-document the whole bench building process, but
since I was following the direction of Sam Allen's book pretty much to the
letter, it didn't seem necessary to do that. But, I'll take a lot of
pictures of the finished product and post them as soon as I can.
Mike
"WD" <[email protected]> wrote in message
news:[email protected]...
> On Mon, 17 Nov 2003 04:15:39 GMT, "Mike in Mystic"
> <[email protected]> wrote:
>
> How about posting some pics in alt.binaries.pictures.woodworking for
> us to see. I am especially interested in the twin-screw vise and your
> workbench. I will be making them in spring.
>
> Thanks
>
> >Hi everyone,
> >
> >I just finished installing the Veritas twin-screw vise on my workbench
(an
> >exact copy of Sam Allen's joiner's bench from his workbench book) and
> >thought I'd write up my experience.
> >
> >Things went fairly smoothly, but not without some hiccups.
> >
> >First, the instructions are quite detailed and as many of you might have
> >heard before, the warning on the front page to not deviate from the
> >instructions are wise and I followed them for the most part. Also, the
> >materials for the vise were MOSTLY of very high quality, especially the
> >screws themselves, which I feel is the most important thing. All the
parts
> >were there (which is good, since I bought this about 3 months ago), so I
was
> >set to go.
> >
> >I used hard maple for the jaws, and made them up at 2" thick, 7" tall,
and
> >24" wide (the width of my bench). It was important to figure out the
> >minimum height of the jaws to accomodate the bench thickness and
hardware,
> >but the instructions made this clear and not difficult. The next step
was
> >to figure out the screw spacing and to adjust the length of the bicycle
> >chain. I used 14 5/8", so I had to remove 6 links from the chain. The
> >instructions say to file the pins down, but I found this to be extremely
> >slow going, so I used my bench grinder, which worked fine. I did have to
> >use a center punch to drive the pins out, which took a little more effort
> >than the instructions made it out to be. Also, the link supplied with
the
> >chain to connect the two ends had the spring-clip alread attached. I
don't
> >really see why Lee Valley sent it this way, and I would have rather had
it
> >separate so as to avoid having to screw with the clip, and possibly
bending
> >it (which I did slightly) removing it from the link pins.
> >
> >Once the chain was set, the next step was laying out and drilling holes
> >through the jaws for the screws and other parts. I took my time here,
and
> >was glad because everything went together fine the first try. I won't
> >really get into this except to say that having a good drill press with a
> >large stroke was a big advantage. Also, a few steps here could've
contained
> >some more hints regarding placement of clamps, etc. I had to reposition
my
> >clamps a few times to get clearance on my drill press. Also, the
> >instructions have you install the screw nuts onto the rear jaws before
> >drilling the bolt mounting holes. This didn't make much sense, because
you
> >have to drill counterbores in the inside face of the rear jaw, so you
have
> >to take the nuts off to lay the jaw flat on the drill press table.
> >
> >After the holes were drilled through the faces of the jaws, and the
mounting
> >holes for the rear jaw were in place, it was necessary to transfer the
holes
> >to the end of the bench in order to drill for the rear jaw mounting
bolts.
> >The rear jaw is attached with barrel bolts placed in cross-drilled holes
> >from the bottom of the bench. I found it pretty tricky to get the rear
jaw
> >in position, but ended up clamping it across the width of the bench,
across
> >the seam where the bench and rear jaw met. The idea was to have a small
> >amount of the rear jaw above the bench surface, so you can plane it down
> >even after you install it. Anyway, it worked out alright. The next
step
> >was to drill the crossing holes for the barell bolts. Since my bench was
> >already constructed, I had to lay on the floor to do this, which could've
> >been more comfortable. If you have the opportunity to install this to
your
> >benchtop with the top upside down on some supports, I would recommend it,
> >not only for comfort, but for the increased accuracy you're sure to have.
I
> >made the jig for locating the crossing holes, but I got one wrong
slightly
> >and had to drill an overlapping hole. It didn't seem to affect the
mounting
> >of the rear jaw at all. One more caveat here, the instructions say to
put
> >some crumpled paper in the hole for the barrel bolts to act as a spring
in
> >aligning them with the bolts. Perhaps it was assumed that the benchtop
> >would be upside down, but I found this to be more of a hassle than a
> >benefit.
> >
> >So, now the rear jaw was installed after quite a bit of effort (at least
> >that's what my back was telling me). Next was the front jaw. In order
to
> >install this, I had to drill clearance holes through the upper end cross
> >braces of my bench base. Because I had already mounted the rear jaw,
this
> >meant drilling from the inside of the base outward (or removing the rear
> >jaw, which I wasn't going to do). Let's just say that laying contorted
on
> >the floor, holding a cordless drill and drilling 1.5" holes through 1.5"
> >wood is not fun. Happily, I got the holes lined up just right the first
> >try.
> >
> >After that, the screws are installed, with the chain in place, and
screwed
> >in by hand until they are holding the front jaw in place against the rear
> >jaw. After aligning the tops and sides of the jaws, the thrust plates
are
> >attached with lag bolts and washers. This is where my first real gripe
with
> >the vise hardware comes up. The instructions DO say to not overtighten
the
> >bolts, so I guess I should've been warned. Even so, I managed to break
the
> >head off one of the bolts! I was ticked off, because I had read the
> >instructions and was consciously not using very much force. I was
getting a
> >firm fit, to be sure, but "overtight"? I don't think so. So, my question
to
> >Lee Valley is, why don't you include better bolts that aren't made of
cheap
> >material? In fact, I think you should include the BEST bolts that you
can
> >find. I'm not sure how the lack of one of the bolts on the thrust plate
> >will have in the long run, but it seemed to be holding, so I proceeded
> >ahead. If anyone has any insight here, it would be appreciated.
> >
> >Another gripe I have is that there weren't any instructions on how to get
> >the vise handles to line up parallel to each other. I tried to install
the
> >chain so that they would be that way, but by the time I had hand
tightened
> >the screws up to the front jaw, and tightened them down in order to
install
> >the thrust plates, they had become out of alignment. I couldn't figure
out
> >any way to adjust them, so hopefully Robin Lee is reading this and can
expla
> >in how this is done. I know I've seen many pictures of the vise on
benches
> >with the handles perfectly parallel, so it must be possible. I'm sure
> >everyone that installs the vise would want their handles aligned, so why
> >there isn't instructions regarding this I really don't understand.
> >
> >Ok, now that the jaws were installed, the cover was ready to go on. The
> >cover consists of two half-round end caps and a center aluminum section.
> >Because I had shorted the chain and had a smaller screw separation, I had
to
> >shorten the cover in order for it to fit between the screw mechanisms.
The
> >instructions say that a hacksaw can be used, and that's true and what I
did.
> >All I can say is, I'm not that proficient at cutting curved pieces of
metal
> >in straight lines with the hacksaw. I did have the idea (probably not
> >novel, I'm sure) of making shallow cuts on either side of the cover, and
> >then cutting down to the face on both sides at the same time, so at least
I
> >ended up with a fairly straight edge. Overall, however I was pretty
> >frustrated by this. I didn't realize how fragile the finish on the cover
> >was, and the initial hacksawing I did was with it held by hand on the
bench
> >top. This resulted in a very scratched finish, which pretty much sucks.
I
> >wish the instructions would have warned me about this. Even more,
however, I
> >wish Lee Valley would just have a question when you order the vise as to
the
> >size of the cover you need and have it precut for you. For the price of
the
> >vise, I think this is a reasonable request. At any rate, I got the cover
in
> >place, albeit pretty well scratched up.
> >
> >So, the final chapter (I didn't realize how long winded this was going to
> >be) was installing the handles. I only mention this because I ran into
> >another example of cheap hardware. The screws provided to attach the
handle
> >end caps to the handles were square drive #8 1-1/4" (maybe 1-1/2"?) wood
> >screws. I drilled pilot holes were the instructions, and set my drill's
> >adjustable torque to 10 (out of 20), which considering the handles are
> >hardwood, should have been fine. Well, as you might have guessed, I
broke
> >the head off one of the screws. Luckily I have a supply of panhead
coarse
> >thread pocket hole screws, and one of these worked fine to replace the
> >broken screw. But, it just illustrates the point that some of the
hardware
> >was not of the best quality in the kit.
> >
> >I did put the vise through it's paces briefly after the install was
finished
> >and I have to say that the vise is GREAT! I was extremely impressed with
> >how much clamping force I could generate. I tried holding a big panel in
> >place with bench dogs across the full vise width, and it worked
wonderfully.
> >I also clamped a 10" wide board vertically in the vise (as if to cut
> >dovetails or something), and it also worked just as I had hoped. I can't
> >wait to actually use it on my upcoming projects.
> >
> >So, in summary, I will have to give the vise a score of maybe 8.5/10, due
to
> >the small issues I have with some of the components. I admit that the
> >problems could have been avoided, but I feel I was using a reasonable
amount
> >of caution and just got stuck by having a few bad parts. I just hope the
> >lack of one of the thrust plate bolts doesn't mess me up in the future.
> >
> >I hope this has been useful for anyone considering this vise. I would
> >definitely buy it again, so that might be the most telling thing of all.
> >
> >Mike
> >
>
>
>
> -----= Posted via Newsfeeds.Com, Uncensored Usenet News =-----
> http://www.newsfeeds.com - The #1 Newsgroup Service in the World!
> -----== Over 100,000 Newsgroups - 19 Different Servers! =-----
"Bob S." <[email protected]> wrote in message
news:[email protected]...
> Mike,
>
> Sure sounds like they changed the installation instructions -
significantly.
> I think your review is longer than the instructions. When I installed
mine,
> it was right about the same time they switched to the new style chain
cover
> plate and although I had all the parts, mine had the old instruction set.
> The problem was quickly resolved by Lee Valley and the rest of the
> installation was straight forward.
>
> As I read your trials and tribulations I kept wondering why I don't
remember
> any of those instructions - like putting paper in the holes or filing down
> pins and there were instructions for aligning the handles. As for the
> hardware furnished, it was all top-grade that I could see and didn't have
> any problems like you. Could be they changed or were you having a bad
hair
> day....;-)
I'm not sure if they changed anything or not in the instructions from the
past. As for me having a bad hair day, it is possible, but my hair is just
about a crew cut, so I tend not to have those problems hehe
>
> As for breaking off a screw in hardwood - if you didn't use the correct
size
> drill for the pilot hole, you can snap a screw in an instant. Just
finished
> refurbing about 40 hard maple door fronts and broke more than one screw
> before I realized the drill bit I was using was one size smaller than it
> should have been.
>
I agree with you, but I used the pilot hole sizes specified in the
instructions. The thrust plate bolt breaking off was definitely my fault in
that I used a little too much force (obviously). The handle screw I don't
feel was my fault because I used a very reasonable torque setting on my
drill. My main point is that I think the hardware shouldn't be so prone to
breaking. I don't know much about the manufacturing of fasteners, but I
would hope that there could be some out there that won't break off as easily
as these did.
> Call Lee Valley and let them know exactly what you feel the problems were.
> Ask for someone that knows about the vise and most likely you'll get a
> person that has installed them several times. I'm sure Robin Lee would be
> grateful for any suggestions or comments that will make the installation
> easier and/or clarify the instructions.
That's a good idea, I think I'll do that.
>
> I've had my twin-screw vise for about 2 years now and its just one of
those
> tools that you never regret buying.
I agree completely. All in all, the gripes I have are very minor, just a
little annoying. In total, the vise install went according to plan and the
vise is working great. I'm sure that this will be an extremely useful
investment for years to come.
Mike
Rob,
Thanks very much for the detailed response. As always, the level of
interaction you have with your customers is exceptional.
A few notes regarding the comments you provided:
1) Regarding the installation of the barrel nuts in for the rear jaw
mounting bolts. I found it quite easy to simply use a screw driver in the
slot on the bottom of the nut and hold in lower than the bolt position. I
had a small flashlight on the ground illuminating the area, so I could see
the protruding bolt end, and then by pushing the bolt against the nut, I
could simply slowly raise the nut and feel the bolt slide into the tapered
recess. It actually wasn't that hard, other than having to lay on the floor
hehe. When I had the paper in the hole, I found that the spring back effect
actually made it harder to make small changes in height to the nut position.
2) Regarding the alignment of the two screw handles. In your website
picture you show the handles perfectly aligned and parallel. Is this only
achieved because you may have used the maximum spacing? I knew enough not
to assume that they would automatcially come out that way, but I didn't see
any mention of the alignment being a contraint of the system. I can think
of at least one situation where having the handles aligned would be
necessary - if you have a bank of drawers or a cabinet door opening at the
end of the bench. Having both handles horizontal would be needed to open
these. I admit I haven't seen this too much, but it's a thought. I guess I
will have to live with the handles as they came out.
3). Regarding the chain cover. I agree with you that the scratching of the
finish was my goof. I won't ask for a replacement. If it bothers me too
much in the future I'll just buy one of your cover kits. Thanks for the
offer, though. As for being overkill to warn against scratching the cover,
I don't think that's the case. You already warn against deforming it in the
hacksawing process, so adding a line "deforming and/or marring the finish"
doesn't seem too big a deal. Since this is the part of the vise that bears
your logo and is the most visible part of the vise (other than the handles,
I suppose), it would be good to have customers avoid the bonehead result
that I managed to do to my vise.
4) My wife says I've spent so much money at your website that I should own
stock in the company. Any plans to go public?? :)
I really do appreciate the responsiveness you gave me and the obvious
attention to even the smallest customer concerns that you have. I already
placed another order at your website yesterday, so obviously you aren't
going to lose my patronage.
Best regards,
Mike Logman
--
There are no stupid questions.
There are a LOT of inquisitive idiots.
"Robin Lee" <[email protected]> wrote in message
news:[email protected]...
> Hi -
>
> Answers to your comments are interspersed below! (cut and pasted from the
> comments I received from our R&D group- note that there's always a bit of
a
> "defensive" slant to a designer's response :) Many of your comments and
> suggestions may help others in the future!
>
> Cheers -
>
> Rob Lee
>
>
>
> "Mike in Mystic" <[email protected]> wrote in message
> news:[email protected]...
> > Hi everyone,
> >
> > I just finished installing the Veritas twin-screw vise on my workbench
(an
> > exact copy of Sam Allen's joiner's bench from his workbench book) and
> > thought I'd write up my experience.
> >
> > Things went fairly smoothly, but not without some hiccups.
> >
> > First, the instructions are quite detailed and as many of you might have
> > heard before, the warning on the front page to not deviate from the
> > instructions are wise and I followed them for the most part. Also, the
> > materials for the vise were MOSTLY of very high quality, especially the
> > screws themselves, which I feel is the most important thing. All the
> parts
> > were there (which is good, since I bought this about 3 months ago), so I
Sounds good, Robin. I knew you'd read the post, so I figured I'd see a
response pretty soon.
I want to clarify to the group-at-large that I didn't mean to sound overly
negative about the vise. I mainly highlighted the few very small issues I
had. It is by far a wonderful product and well-designed. I am extremely
happy with it overall, so don't take my comments in too harsh a context.
Mike
"Robin Lee" <[email protected]> wrote in message
news:[email protected]...
> Mike -
>
> No need to call - saw your post, have forwarded it around for comments, am
> drafting a reply, and will post here later!
>
> Cheers -
>
> Rob Lee
>
> "Mike in Mystic" <[email protected]> wrote in message
> news:[email protected]...
> > "Bob S." <[email protected]> wrote in message
> > news:[email protected]...
> > > Mike,
> > >
> > > Sure sounds like they changed the installation instructions -
> > significantly.
> > > I think your review is longer than the instructions. When I installed
> > mine,
> > > it was right about the same time they switched to the new style chain
> > cover
> > > plate and although I had all the parts, mine had the old instruction
> set.
> > > The problem was quickly resolved by Lee Valley and the rest of the
> > > installation was straight forward.
> > >
> > > As I read your trials and tribulations I kept wondering why I don't
> > remember
> > > any of those instructions - like putting paper in the holes or filing
> down
> > > pins and there were instructions for aligning the handles. As for the
> > > hardware furnished, it was all top-grade that I could see and didn't
> have
> > > any problems like you. Could be they changed or were you having a bad
> > hair
> > > day....;-)
> >
> > I'm not sure if they changed anything or not in the instructions from
the
> > past. As for me having a bad hair day, it is possible, but my hair is
> just
> > about a crew cut, so I tend not to have those problems hehe
> >
> > >
> > > As for breaking off a screw in hardwood - if you didn't use the
correct
> > size
> > > drill for the pilot hole, you can snap a screw in an instant. Just
> > finished
> > > refurbing about 40 hard maple door fronts and broke more than one
screw
> > > before I realized the drill bit I was using was one size smaller than
it
> > > should have been.
> > >
> > I agree with you, but I used the pilot hole sizes specified in the
> > instructions. The thrust plate bolt breaking off was definitely my
fault
> in
> > that I used a little too much force (obviously). The handle screw I
don't
> > feel was my fault because I used a very reasonable torque setting on my
> > drill. My main point is that I think the hardware shouldn't be so prone
> to
> > breaking. I don't know much about the manufacturing of fasteners, but I
> > would hope that there could be some out there that won't break off as
> easily
> > as these did.
> >
> > > Call Lee Valley and let them know exactly what you feel the problems
> were.
> > > Ask for someone that knows about the vise and most likely you'll get a
> > > person that has installed them several times. I'm sure Robin Lee
would
> be
> > > grateful for any suggestions or comments that will make the
installation
> > > easier and/or clarify the instructions.
> >
> > That's a good idea, I think I'll do that.
> >
> > >
> > > I've had my twin-screw vise for about 2 years now and its just one of
> > those
> > > tools that you never regret buying.
> >
> > I agree completely. All in all, the gripes I have are very minor, just
a
> > little annoying. In total, the vise install went according to plan and
> the
> > vise is working great. I'm sure that this will be an extremely useful
> > investment for years to come.
> >
> > Mike
> >
> >
>
>
Mike -
No need to call - saw your post, have forwarded it around for comments, am
drafting a reply, and will post here later!
Cheers -
Rob Lee
"Mike in Mystic" <[email protected]> wrote in message
news:[email protected]...
> "Bob S." <[email protected]> wrote in message
> news:[email protected]...
> > Mike,
> >
> > Sure sounds like they changed the installation instructions -
> significantly.
> > I think your review is longer than the instructions. When I installed
> mine,
> > it was right about the same time they switched to the new style chain
> cover
> > plate and although I had all the parts, mine had the old instruction
set.
> > The problem was quickly resolved by Lee Valley and the rest of the
> > installation was straight forward.
> >
> > As I read your trials and tribulations I kept wondering why I don't
> remember
> > any of those instructions - like putting paper in the holes or filing
down
> > pins and there were instructions for aligning the handles. As for the
> > hardware furnished, it was all top-grade that I could see and didn't
have
> > any problems like you. Could be they changed or were you having a bad
> hair
> > day....;-)
>
> I'm not sure if they changed anything or not in the instructions from the
> past. As for me having a bad hair day, it is possible, but my hair is
just
> about a crew cut, so I tend not to have those problems hehe
>
> >
> > As for breaking off a screw in hardwood - if you didn't use the correct
> size
> > drill for the pilot hole, you can snap a screw in an instant. Just
> finished
> > refurbing about 40 hard maple door fronts and broke more than one screw
> > before I realized the drill bit I was using was one size smaller than it
> > should have been.
> >
> I agree with you, but I used the pilot hole sizes specified in the
> instructions. The thrust plate bolt breaking off was definitely my fault
in
> that I used a little too much force (obviously). The handle screw I don't
> feel was my fault because I used a very reasonable torque setting on my
> drill. My main point is that I think the hardware shouldn't be so prone
to
> breaking. I don't know much about the manufacturing of fasteners, but I
> would hope that there could be some out there that won't break off as
easily
> as these did.
>
> > Call Lee Valley and let them know exactly what you feel the problems
were.
> > Ask for someone that knows about the vise and most likely you'll get a
> > person that has installed them several times. I'm sure Robin Lee would
be
> > grateful for any suggestions or comments that will make the installation
> > easier and/or clarify the instructions.
>
> That's a good idea, I think I'll do that.
>
> >
> > I've had my twin-screw vise for about 2 years now and its just one of
> those
> > tools that you never regret buying.
>
> I agree completely. All in all, the gripes I have are very minor, just a
> little annoying. In total, the vise install went according to plan and
the
> vise is working great. I'm sure that this will be an extremely useful
> investment for years to come.
>
> Mike
>
>
Mike:
I bet it took just as long if not longer to write that report. Glad to see
you cranking on the projects.
"Mike in Mystic" <[email protected]> wrote in message
news:[email protected]...
> Hi everyone,
>
> I just finished installing the Veritas twin-screw vise on my workbench (an
> exact copy of Sam Allen's joiner's bench from his workbench book) and
> thought I'd write up my experience.
>
> Things went fairly smoothly, but not without some hiccups.
>
> First, the instructions are quite detailed and as many of you might have
> heard before, the warning on the front page to not deviate from the
> instructions are wise and I followed them for the most part. Also, the
> materials for the vise were MOSTLY of very high quality, especially the
> screws themselves, which I feel is the most important thing. All the
parts
> were there (which is good, since I bought this about 3 months ago), so I
was
> set to go.
>
> I used hard maple for the jaws, and made them up at 2" thick, 7" tall, and
> 24" wide (the width of my bench). It was important to figure out the
> minimum height of the jaws to accomodate the bench thickness and hardware,
> but the instructions made this clear and not difficult. The next step was
> to figure out the screw spacing and to adjust the length of the bicycle
> chain. I used 14 5/8", so I had to remove 6 links from the chain. The
> instructions say to file the pins down, but I found this to be extremely
> slow going, so I used my bench grinder, which worked fine. I did have to
> use a center punch to drive the pins out, which took a little more effort
> than the instructions made it out to be. Also, the link supplied with the
> chain to connect the two ends had the spring-clip alread attached. I
don't
> really see why Lee Valley sent it this way, and I would have rather had it
> separate so as to avoid having to screw with the clip, and possibly
bending
> it (which I did slightly) removing it from the link pins.
>
> Once the chain was set, the next step was laying out and drilling holes
> through the jaws for the screws and other parts. I took my time here, and
> was glad because everything went together fine the first try. I won't
> really get into this except to say that having a good drill press with a
> large stroke was a big advantage. Also, a few steps here could've
contained
> some more hints regarding placement of clamps, etc. I had to reposition
my
> clamps a few times to get clearance on my drill press. Also, the
> instructions have you install the screw nuts onto the rear jaws before
> drilling the bolt mounting holes. This didn't make much sense, because
you
> have to drill counterbores in the inside face of the rear jaw, so you have
> to take the nuts off to lay the jaw flat on the drill press table.
>
> After the holes were drilled through the faces of the jaws, and the
mounting
> holes for the rear jaw were in place, it was necessary to transfer the
holes
> to the end of the bench in order to drill for the rear jaw mounting bolts.
> The rear jaw is attached with barrel bolts placed in cross-drilled holes
> from the bottom of the bench. I found it pretty tricky to get the rear
jaw
> in position, but ended up clamping it across the width of the bench,
across
> the seam where the bench and rear jaw met. The idea was to have a small
> amount of the rear jaw above the bench surface, so you can plane it down
> even after you install it. Anyway, it worked out alright. The next step
> was to drill the crossing holes for the barell bolts. Since my bench was
> already constructed, I had to lay on the floor to do this, which could've
> been more comfortable. If you have the opportunity to install this to
your
> benchtop with the top upside down on some supports, I would recommend it,
> not only for comfort, but for the increased accuracy you're sure to have.
I
> made the jig for locating the crossing holes, but I got one wrong slightly
> and had to drill an overlapping hole. It didn't seem to affect the
mounting
> of the rear jaw at all. One more caveat here, the instructions say to put
> some crumpled paper in the hole for the barrel bolts to act as a spring in
> aligning them with the bolts. Perhaps it was assumed that the benchtop
> would be upside down, but I found this to be more of a hassle than a
> benefit.
>
> So, now the rear jaw was installed after quite a bit of effort (at least
> that's what my back was telling me). Next was the front jaw. In order to
> install this, I had to drill clearance holes through the upper end cross
> braces of my bench base. Because I had already mounted the rear jaw, this
> meant drilling from the inside of the base outward (or removing the rear
> jaw, which I wasn't going to do). Let's just say that laying contorted on
> the floor, holding a cordless drill and drilling 1.5" holes through 1.5"
> wood is not fun. Happily, I got the holes lined up just right the first
> try.
>
> After that, the screws are installed, with the chain in place, and screwed
> in by hand until they are holding the front jaw in place against the rear
> jaw. After aligning the tops and sides of the jaws, the thrust plates are
> attached with lag bolts and washers. This is where my first real gripe
with
> the vise hardware comes up. The instructions DO say to not overtighten
the
> bolts, so I guess I should've been warned. Even so, I managed to break
the
> head off one of the bolts! I was ticked off, because I had read the
> instructions and was consciously not using very much force. I was getting
a
> firm fit, to be sure, but "overtight"? I don't think so. So, my question
to
> Lee Valley is, why don't you include better bolts that aren't made of
cheap
> material? In fact, I think you should include the BEST bolts that you can
> find. I'm not sure how the lack of one of the bolts on the thrust plate
> will have in the long run, but it seemed to be holding, so I proceeded
> ahead. If anyone has any insight here, it would be appreciated.
>
> Another gripe I have is that there weren't any instructions on how to get
> the vise handles to line up parallel to each other. I tried to install
the
> chain so that they would be that way, but by the time I had hand tightened
> the screws up to the front jaw, and tightened them down in order to
install
> the thrust plates, they had become out of alignment. I couldn't figure
out
> any way to adjust them, so hopefully Robin Lee is reading this and can
expla
> in how this is done. I know I've seen many pictures of the vise on
benches
> with the handles perfectly parallel, so it must be possible. I'm sure
> everyone that installs the vise would want their handles aligned, so why
> there isn't instructions regarding this I really don't understand.
>
> Ok, now that the jaws were installed, the cover was ready to go on. The
> cover consists of two half-round end caps and a center aluminum section.
> Because I had shorted the chain and had a smaller screw separation, I had
to
> shorten the cover in order for it to fit between the screw mechanisms.
The
> instructions say that a hacksaw can be used, and that's true and what I
did.
> All I can say is, I'm not that proficient at cutting curved pieces of
metal
> in straight lines with the hacksaw. I did have the idea (probably not
> novel, I'm sure) of making shallow cuts on either side of the cover, and
> then cutting down to the face on both sides at the same time, so at least
I
> ended up with a fairly straight edge. Overall, however I was pretty
> frustrated by this. I didn't realize how fragile the finish on the cover
> was, and the initial hacksawing I did was with it held by hand on the
bench
> top. This resulted in a very scratched finish, which pretty much sucks.
I
> wish the instructions would have warned me about this. Even more, however,
I
> wish Lee Valley would just have a question when you order the vise as to
the
> size of the cover you need and have it precut for you. For the price of
the
> vise, I think this is a reasonable request. At any rate, I got the cover
in
> place, albeit pretty well scratched up.
>
> So, the final chapter (I didn't realize how long winded this was going to
> be) was installing the handles. I only mention this because I ran into
> another example of cheap hardware. The screws provided to attach the
handle
> end caps to the handles were square drive #8 1-1/4" (maybe 1-1/2"?) wood
> screws. I drilled pilot holes were the instructions, and set my drill's
> adjustable torque to 10 (out of 20), which considering the handles are
> hardwood, should have been fine. Well, as you might have guessed, I broke
> the head off one of the screws. Luckily I have a supply of panhead coarse
> thread pocket hole screws, and one of these worked fine to replace the
> broken screw. But, it just illustrates the point that some of the
hardware
> was not of the best quality in the kit.
>
> I did put the vise through it's paces briefly after the install was
finished
> and I have to say that the vise is GREAT! I was extremely impressed with
> how much clamping force I could generate. I tried holding a big panel in
> place with bench dogs across the full vise width, and it worked
wonderfully.
> I also clamped a 10" wide board vertically in the vise (as if to cut
> dovetails or something), and it also worked just as I had hoped. I can't
> wait to actually use it on my upcoming projects.
>
> So, in summary, I will have to give the vise a score of maybe 8.5/10, due
to
> the small issues I have with some of the components. I admit that the
> problems could have been avoided, but I feel I was using a reasonable
amount
> of caution and just got stuck by having a few bad parts. I just hope the
> lack of one of the thrust plate bolts doesn't mess me up in the future.
>
> I hope this has been useful for anyone considering this vise. I would
> definitely buy it again, so that might be the most telling thing of all.
>
> Mike
>
>
Please, do not go public. As soon as you do that, you pander to the
stock holders who don't give a rat's ass about the quality of your
products and the lively hood of your employees. You'll start to run
the company in ways that the "Stock Anylists" like in order to
influence the stock price.
Just say No!
Dan
On Tue, 18 Nov 2003 11:45:44 -0500, "Robin Lee" <[email protected]>
wrote:
>Mike -
>
>I'll take a bow on behalf of the designer who sent back a detailed response
>almost as long as your original post - few of the comments (in this case)
>were mine .... :)
>
>As for the aligned handles on the website - that's probably Murphy's work...
>if a "random" event could take place which would suggest a design feature -
>it'll happen in photography. We'll make a note of it.... Then too, it's
>possible that the nut on one screw was fixed after handle alignment, or
>shimmed out of a recess... rotating the nut should provide 90 degrees of
>adjustment, with finer adjustment (less than 90) coming from shims....
>
>Chain cover - offer stands.... the kit includes end caps (which you don't
>need)...the cut extrusion won't cost us too much - and we'll put it in with
>your next order....I can try and do it today- but your order's probably
>packed and in the truck by now....
>
>The shares'll have to wait for at least one more generation - not happening
>this one!
>
>Cheers -
>
>Rob Lee
"RKON" <[email protected]> wrote in message
news:d5dub.6686$PJ6.4778@okepread05...
> Mike:
>
> I bet it took just as long if not longer to write that report. Glad to see
> you cranking on the projects.
Well, not exactly. I type 95 words/minute, so it didn't take me very long
to write that. Even so, I didn't mean to ramble quite that much, but
sometimes that's how it works out. I guess I overdid the "small details".
It's tough getting time to work on things with a 3 month old son, but I am
slowly getting the hang of it and lowering my expectations. There's been
several occasions when it was my "turn" for free time and I chose to just
stay with Charlie, rather than go out to the shop. I am all set now that
the bench is done to get going on the dresser for the nursery. Will
probably end up only about 4.5 months behind schedule hehe.
Mike
> Well, not exactly. I type 95 words/minute, so it didn't take me very long
> to write that. Even so, I didn't mean to ramble quite that much, but
> sometimes that's how it works out. I guess I overdid the "small details".
I'm impressed.. 95 words a minute.
> It's tough getting time to work on things with a 3 month old son, but I am
> slowly getting the hang of it and lowering my expectations. There's been
> several occasions when it was my "turn" for free time and I chose to just
> stay with Charlie, rather than go out to the shop.
I know exactly what you mean with balancing time with having a 3 month old
child. Working on projects is rewarding but not nearly as rewarding as
spending time with the kids and watching them grow up. Enjoy it because
they grow up real fast.
I have two girls who both play travel soccer and every weekend spring and
fall I have been on the road. I enjoy the time very much. That does not
leave much time for yourself. I have done a couple small projects of
building a small picket fence and some planters. Not much to write home to
momma about.
I waiting till after the Holidays to get the rest of my toys, I mean
equipment. SWMBO wants some storage cabinets and such. I looking forward to
these projects once I finish the shop. Had a small plumbing nightmare with
the Hot water heater that set me back. More of a worrisome headache than
anything.
Be Good !!
"Mike in Mystic" <[email protected]> wrote in message
news:[email protected]...
> "RKON" <[email protected]> wrote in message
> news:d5dub.6686$PJ6.4778@okepread05...
> > Mike:
> >
> > I bet it took just as long if not longer to write that report. Glad to
see
> > you cranking on the projects.
>
> Well, not exactly. I type 95 words/minute, so it didn't take me very long
> to write that. Even so, I didn't mean to ramble quite that much, but
> sometimes that's how it works out. I guess I overdid the "small details".
>
> It's tough getting time to work on things with a 3 month old son, but I am
> slowly getting the hang of it and lowering my expectations. There's been
> several occasions when it was my "turn" for free time and I chose to just
> stay with Charlie, rather than go out to the shop. I am all set now that
> the bench is done to get going on the dresser for the nursery. Will
> probably end up only about 4.5 months behind schedule hehe.
>
>
> Mike
>
>
>
Mike,
Sure sounds like they changed the installation instructions - significantly.
I think your review is longer than the instructions. When I installed mine,
it was right about the same time they switched to the new style chain cover
plate and although I had all the parts, mine had the old instruction set.
The problem was quickly resolved by Lee Valley and the rest of the
installation was straight forward.
As I read your trials and tribulations I kept wondering why I don't remember
any of those instructions - like putting paper in the holes or filing down
pins and there were instructions for aligning the handles. As for the
hardware furnished, it was all top-grade that I could see and didn't have
any problems like you. Could be they changed or were you having a bad hair
day....;-)
As for breaking off a screw in hardwood - if you didn't use the correct size
drill for the pilot hole, you can snap a screw in an instant. Just finished
refurbing about 40 hard maple door fronts and broke more than one screw
before I realized the drill bit I was using was one size smaller than it
should have been.
Call Lee Valley and let them know exactly what you feel the problems were.
Ask for someone that knows about the vise and most likely you'll get a
person that has installed them several times. I'm sure Robin Lee would be
grateful for any suggestions or comments that will make the installation
easier and/or clarify the instructions.
I've had my twin-screw vise for about 2 years now and its just one of those
tools that you never regret buying.
Bob S.
Mike,
I installed that vise last winter while building the "Shop Notes" bench. I
don't remember having that much trouble, although Murphy is usually right
there when I do something like that.
I did have a small problem with one of the parts of the vise itself, it was
incorrectly machined. Veritas (Lee Valley) quickly and politely exchanged it
for me.
I did not have to cut the cover, and I built mine out of oak. I like the
speed knob on one side. I like the vice, and in fact, I used it last night.
Bill
"Mike in Mystic" <[email protected]> wrote in message
news:[email protected]...
> Hi everyone,
>
> I just finished installing the Veritas twin-screw vise on my workbench (an
> exact copy of Sam Allen's joiner's bench from his workbench book) and
> thought I'd write up my experience.
>
> Things went fairly smoothly, but not without some hiccups.
>
> First, the instructions are quite detailed and as many of you might have
> heard before, the warning on the front page to not deviate from the
> instructions are wise and I followed them for the most part. Also, the
> materials for the vise were MOSTLY of very high quality, especially the
> screws themselves, which I feel is the most important thing. All the
parts
> were there (which is good, since I bought this about 3 months ago), so I
was
> set to go.
>
> I used hard maple for the jaws, and made them up at 2" thick, 7" tall, and
> 24" wide (the width of my bench). It was important to figure out the
> minimum height of the jaws to accomodate the bench thickness and hardware,
> but the instructions made this clear and not difficult. The next step was
> to figure out the screw spacing and to adjust the length of the bicycle
> chain. I used 14 5/8", so I had to remove 6 links from the chain. The
> instructions say to file the pins down, but I found this to be extremely
> slow going, so I used my bench grinder, which worked fine. I did have to
> use a center punch to drive the pins out, which took a little more effort
> than the instructions made it out to be. Also, the link supplied with the
> chain to connect the two ends had the spring-clip alread attached. I
don't
> really see why Lee Valley sent it this way, and I would have rather had it
> separate so as to avoid having to screw with the clip, and possibly
bending
> it (which I did slightly) removing it from the link pins.
>
> Once the chain was set, the next step was laying out and drilling holes
> through the jaws for the screws and other parts. I took my time here, and
> was glad because everything went together fine the first try. I won't
> really get into this except to say that having a good drill press with a
> large stroke was a big advantage. Also, a few steps here could've
contained
> some more hints regarding placement of clamps, etc. I had to reposition
my
> clamps a few times to get clearance on my drill press. Also, the
> instructions have you install the screw nuts onto the rear jaws before
> drilling the bolt mounting holes. This didn't make much sense, because
you
> have to drill counterbores in the inside face of the rear jaw, so you have
> to take the nuts off to lay the jaw flat on the drill press table.
>
> After the holes were drilled through the faces of the jaws, and the
mounting
> holes for the rear jaw were in place, it was necessary to transfer the
holes
> to the end of the bench in order to drill for the rear jaw mounting bolts.
> The rear jaw is attached with barrel bolts placed in cross-drilled holes
> from the bottom of the bench. I found it pretty tricky to get the rear
jaw
> in position, but ended up clamping it across the width of the bench,
across
> the seam where the bench and rear jaw met. The idea was to have a small
> amount of the rear jaw above the bench surface, so you can plane it down
> even after you install it. Anyway, it worked out alright. The next step
> was to drill the crossing holes for the barell bolts. Since my bench was
> already constructed, I had to lay on the floor to do this, which could've
> been more comfortable. If you have the opportunity to install this to
your
> benchtop with the top upside down on some supports, I would recommend it,
> not only for comfort, but for the increased accuracy you're sure to have.
I
> made the jig for locating the crossing holes, but I got one wrong slightly
> and had to drill an overlapping hole. It didn't seem to affect the
mounting
> of the rear jaw at all. One more caveat here, the instructions say to put
> some crumpled paper in the hole for the barrel bolts to act as a spring in
> aligning them with the bolts. Perhaps it was assumed that the benchtop
> would be upside down, but I found this to be more of a hassle than a
> benefit.
>
> So, now the rear jaw was installed after quite a bit of effort (at least
> that's what my back was telling me). Next was the front jaw. In order to
> install this, I had to drill clearance holes through the upper end cross
> braces of my bench base. Because I had already mounted the rear jaw, this
> meant drilling from the inside of the base outward (or removing the rear
> jaw, which I wasn't going to do). Let's just say that laying contorted on
> the floor, holding a cordless drill and drilling 1.5" holes through 1.5"
> wood is not fun. Happily, I got the holes lined up just right the first
> try.
>
> After that, the screws are installed, with the chain in place, and screwed
> in by hand until they are holding the front jaw in place against the rear
> jaw. After aligning the tops and sides of the jaws, the thrust plates are
> attached with lag bolts and washers. This is where my first real gripe
with
> the vise hardware comes up. The instructions DO say to not overtighten
the
> bolts, so I guess I should've been warned. Even so, I managed to break
the
> head off one of the bolts! I was ticked off, because I had read the
> instructions and was consciously not using very much force. I was getting
a
> firm fit, to be sure, but "overtight"? I don't think so. So, my question
to
> Lee Valley is, why don't you include better bolts that aren't made of
cheap
> material? In fact, I think you should include the BEST bolts that you can
> find. I'm not sure how the lack of one of the bolts on the thrust plate
> will have in the long run, but it seemed to be holding, so I proceeded
> ahead. If anyone has any insight here, it would be appreciated.
>
> Another gripe I have is that there weren't any instructions on how to get
> the vise handles to line up parallel to each other. I tried to install
the
> chain so that they would be that way, but by the time I had hand tightened
> the screws up to the front jaw, and tightened them down in order to
install
> the thrust plates, they had become out of alignment. I couldn't figure
out
> any way to adjust them, so hopefully Robin Lee is reading this and can
expla
> in how this is done. I know I've seen many pictures of the vise on
benches
> with the handles perfectly parallel, so it must be possible. I'm sure
> everyone that installs the vise would want their handles aligned, so why
> there isn't instructions regarding this I really don't understand.
>
> Ok, now that the jaws were installed, the cover was ready to go on. The
> cover consists of two half-round end caps and a center aluminum section.
> Because I had shorted the chain and had a smaller screw separation, I had
to
> shorten the cover in order for it to fit between the screw mechanisms.
The
> instructions say that a hacksaw can be used, and that's true and what I
did.
> All I can say is, I'm not that proficient at cutting curved pieces of
metal
> in straight lines with the hacksaw. I did have the idea (probably not
> novel, I'm sure) of making shallow cuts on either side of the cover, and
> then cutting down to the face on both sides at the same time, so at least
I
> ended up with a fairly straight edge. Overall, however I was pretty
> frustrated by this. I didn't realize how fragile the finish on the cover
> was, and the initial hacksawing I did was with it held by hand on the
bench
> top. This resulted in a very scratched finish, which pretty much sucks.
I
> wish the instructions would have warned me about this. Even more, however,
I
> wish Lee Valley would just have a question when you order the vise as to
the
> size of the cover you need and have it precut for you. For the price of
the
> vise, I think this is a reasonable request. At any rate, I got the cover
in
> place, albeit pretty well scratched up.
>
> So, the final chapter (I didn't realize how long winded this was going to
> be) was installing the handles. I only mention this because I ran into
> another example of cheap hardware. The screws provided to attach the
handle
> end caps to the handles were square drive #8 1-1/4" (maybe 1-1/2"?) wood
> screws. I drilled pilot holes were the instructions, and set my drill's
> adjustable torque to 10 (out of 20), which considering the handles are
> hardwood, should have been fine. Well, as you might have guessed, I broke
> the head off one of the screws. Luckily I have a supply of panhead coarse
> thread pocket hole screws, and one of these worked fine to replace the
> broken screw. But, it just illustrates the point that some of the
hardware
> was not of the best quality in the kit.
>
> I did put the vise through it's paces briefly after the install was
finished
> and I have to say that the vise is GREAT! I was extremely impressed with
> how much clamping force I could generate. I tried holding a big panel in
> place with bench dogs across the full vise width, and it worked
wonderfully.
> I also clamped a 10" wide board vertically in the vise (as if to cut
> dovetails or something), and it also worked just as I had hoped. I can't
> wait to actually use it on my upcoming projects.
>
> So, in summary, I will have to give the vise a score of maybe 8.5/10, due
to
> the small issues I have with some of the components. I admit that the
> problems could have been avoided, but I feel I was using a reasonable
amount
> of caution and just got stuck by having a few bad parts. I just hope the
> lack of one of the thrust plate bolts doesn't mess me up in the future.
>
> I hope this has been useful for anyone considering this vise. I would
> definitely buy it again, so that might be the most telling thing of all.
>
> Mike
>
>