I am in the "I need a new toy" mode and am looking at a bandsaw.
Right now, I see the saw as being able to handle basic cutting and
some resawing. The resawing I can't see as ever being more than 12",
most in the 6-8" range at most. This is for a hobby, no production
work, so saw will probably be used only few times a month.
Given this, I have been focussing on the Rikon 325 and the Rikon 345.
The 345 has a 10 degree tilt to the left, which would allow me to use
it for doing dovetails if need be (watched David Marks do this with
the tool chest he made). I do have a 220v circuit I put in past year
"just in case" I ever needed it. Being the additional cost of a
mobile base and blades, I definately can't go more than the $1000 mark
total of the saw. The rikon 325 is $750, but will get (10% off next
month for their sale day). The Rikon 345 is $1250, but on sale for
$999 right now.
Any thoughts to these two or recommendation for other bandsaws? I
would like to get the most flexibility and power versus the cost as I
can. While many recommend larger saws such as the Laguna, those are
towards the $2000 range and far too much out of my price range or
need.
Any recommendations and/or comments greatly appreciated.
- Clayton
"Malathan" <[email protected]> wrote in message
news:[email protected]...
> What about the Grizzly 513x? That was another one I was considering.
> I am leaning more towards an 18" saw rather than a 14" (with riser),
> figuring in the long run it would be better and be a better value.
> $1000 is stretching my budget though.
A bit more on the subject of roller bearings and upper wheel adjustment.
Roller bearings look great on paper.
Roller bearings are very noisy and create vibration when you cut woods that
have sticky saw dust. Take SYP or green wood for instance.
The dust sticks to the bearing surfaces and gets pounded. The saw dust
being pounded sticks to the blade and the bearings and can be very difficult
to remove. This dirty and uneven surface makes lots of noise and vibration.
Upper wheel adjustment on my Rikon was a constant problem for me. I had to
continuously monitor the tracking of the blade to insure that the blade
stayed properly situated in the guides. With the noise coming from the
bearings it was easy to tell when the blade moved out of position. The
noise got louder or quieter as the blade moved to and or from the thrust
bearing.
With better band saws, like the Laguna that I now have, blade tracking is
not an issue. Unless I go straight from a 1" to a 1/4" wide blade I often
do not have to adjust the top wheel tilt at all. Actually I don't even need
to use guides in many situations as the blade stays put.
My advice, what ever brand saw you get, strongly consider adding ceramic
guides as soon a possible. Ceramic guides can touch the blade and tend to
scrape and keep the blade clean. Since there are no moving parts in the
guides the noise and vibration is mostly nonexistent.
On Jan 29, 10:04 pm, Malathan <[email protected]> wrote:
> What about the Grizzly 513x? That was another one I was considering.
> I am leaning more towards an 18" saw rather than a 14" (with riser),
> figuring in the long run it would be better and be a better value.
> $1000 is stretching my budget though.
>
Having recently purchased my first bandsaw, a Grizzly G0513X, I cannot
offer much advice in the way of comparison or experience but I can
tell you that I'm happy with it.
It seems to be solidly built. The cast iron wheels are well balanced
and it operates smoothly. Blade tracking adjustment is easy and the
blade shows up on the wheel well. Using a 1" TimerWolf blade it re-
sawed some walnut effortlessly without drift or barrel cutting.
Some things I don't like about it: The lower bearing guide allen bolts
are difficult to access making adjustments a pain. Installing/removing
a 1" blade is a bit tricky as there's not much wiggle room. The table
insert is a cheap piece of plastic that sits too far recessed leaving
a lip that narrow stock can catch on when first feeding.
Admittedly I didn't do much research of other brands before
purchasing. I find the middle and upper tier Grizzly products to be a
good value and the customer service is great. It doesn't hurt that I
live 2 miles from a Grizzly warehouse so I can see the products, talk
to the staff and save the shipping costs.
Currently it sells for $975. It was advertised in Wood magazine only
for $795 but that sale ended Dec 31st. I don't know if Grizzly will
haggle or not, but if your budget is tight it might be worth a shot
knowing it just came off sale.
Brian
On Jan 30, 8:49 am, "Leon" <[email protected]> wrote:
<snip>
> A bit more on the subject of roller bearings and upper wheel adjustment.
> Roller bearings look great on paper.
> Roller bearings are very noisy and create vibration when you cut woods that
> have sticky saw dust. Take SYP or green wood for instance.
> The dust sticks to the bearing surfaces and gets pounded. The saw dust
> being pounded sticks to the blade and the bearings and can be very difficult
> to remove. This dirty and uneven surface makes lots of noise and vibration.
<snip>
Huh. I can see that happening, but why would P-matic put them on
their saws as standard, and Carter sell them as an upgrade? Not
arguing with you, but rather wondering about the significance of the
issue you cite.
Please see the following review for an alternate opinion on roller
bearings:
http://www.newwoodworker.com/reviews/crtrlrguidrvu.html
D'ohBoy
Malathan wrote:
> I have decided on the Rikon 325. Given what I will be using it for
> and how often, think this 14" saw will do everything i want it to do
> including some basic resawing. Also, give the fact that my local
> Woodcraft has all power equipment on sale for 10% off, that brings it
> down to $675. Anything else would be a $300+ jump up, which I don't
> think would justify the benefits.
>
> Thank you everyone for taking time to respond. Your feedback was very
> helpful.
>
> - Clayton
Ummm, yeah... I don't know how to say this....
Just went down to the shop to put the stand for the Rikon together,
then the mobile base, then put the stand on the base and think about
possibly hefting the body of the saw up onto the base.... I am a big
boy and have carried a Jet 161/2 floor standing drill press down to
the basement.....
Then I noticed that one of the bolt holes to attach the body to the
base was drilled off the location where the other three were. Huh.
Intentional? Ummm, no. More like a QC problem. Damn. Would hafta
drill it out or something as there is a nut that the bolt threads into
welded to the base below. So no tolerance of 1/4" off. Damn. And
that plate welded to the bottom of the saw isn't going to be swapped
out either. Don't think I can drill it out either.
When I get it back to Woodcraft, I am going to replace it with a
Powermatic. The 14" they have on sale. Free riser block. $799 after
rebate. $45 bucks more. Shoulda done it in the first place.
Just disappointing. Mebbe check yours out afore ya lug it down to the
basement and have to lug it back out.
Maybe before you take it out of the store. Damn. I've heard of
people having to deal with crap like this with other mfr's but I
thought I PAID for QC.
Disheartened D'ohBoy, who's gonna hafta lug that bitch outta the
basement.
"Malathan" <[email protected]> wrote in message
news:[email protected]...
>I am in the "I need a new toy" mode and am looking at a bandsaw.
> Right now, I see the saw as being able to handle basic cutting and
> some resawing. The resawing I can't see as ever being more than 12",
> most in the 6-8" range at most. This is for a hobby, no production
> work, so saw will probably be used only few times a month.
>
> Given this, I have been focussing on the Rikon 325 and the Rikon 345.
> The 345 has a 10 degree tilt to the left, which would allow me to use
> it for doing dovetails if need be (watched David Marks do this with
> the tool chest he made). I do have a 220v circuit I put in past year
> "just in case" I ever needed it. Being the additional cost of a
> mobile base and blades, I definately can't go more than the $1000 mark
> total of the saw. The rikon 325 is $750, but will get (10% off next
> month for their sale day). The Rikon 345 is $1250, but on sale for
> $999 right now.
>
> Any thoughts to these two or recommendation for other bandsaws? I
> would like to get the most flexibility and power versus the cost as I
> can. While many recommend larger saws such as the Laguna, those are
> towards the $2000 range and far too much out of my price range or
> need.
>
> Any recommendations and/or comments greatly appreciated.
>
> - Clayton
For the money and a first saw IMHO the Rikon is a decent deal. It is not
going to give performance near a Minimax or Laguna. It will however compete
with the normal name brands.
That said, I had the 18" Rikon and had problems with tracking and absolutely
hated the roller guide bearings. This is not to say that Rikon is the
problem here but it only comes with roller guide bearings.
Called Grizzly. Even talked with a sales manager. They would not
budge at all. Very firm and irresolute. That is a shame being that
such attitudes lose them customers.
- Clayton
On 29 Jan 2007 22:24:55 -0800, "[email protected]"
<[email protected]> wrote:
>On Jan 29, 10:04 pm, Malathan <[email protected]> wrote:
>> What about the Grizzly 513x? That was another one I was considering.
>> I am leaning more towards an 18" saw rather than a 14" (with riser),
>> figuring in the long run it would be better and be a better value.
>> $1000 is stretching my budget though.
>>
>
>Having recently purchased my first bandsaw, a Grizzly G0513X, I cannot
>offer much advice in the way of comparison or experience but I can
>tell you that I'm happy with it.
>
>It seems to be solidly built. The cast iron wheels are well balanced
>and it operates smoothly. Blade tracking adjustment is easy and the
>blade shows up on the wheel well. Using a 1" TimerWolf blade it re-
>sawed some walnut effortlessly without drift or barrel cutting.
>
>Some things I don't like about it: The lower bearing guide allen bolts
>are difficult to access making adjustments a pain. Installing/removing
>a 1" blade is a bit tricky as there's not much wiggle room. The table
>insert is a cheap piece of plastic that sits too far recessed leaving
>a lip that narrow stock can catch on when first feeding.
>
>Admittedly I didn't do much research of other brands before
>purchasing. I find the middle and upper tier Grizzly products to be a
>good value and the customer service is great. It doesn't hurt that I
>live 2 miles from a Grizzly warehouse so I can see the products, talk
>to the staff and save the shipping costs.
>
>Currently it sells for $975. It was advertised in Wood magazine only
>for $795 but that sale ended Dec 31st. I don't know if Grizzly will
>haggle or not, but if your budget is tight it might be worth a shot
>knowing it just came off sale.
>
>Brian
>
>
I don't have one of these, but I imagine that price wise it will
compare to the Rikon. From the budget you stated the Rikon is a great
option. As I said earlier I have the Rikon and I'm happy. I would
prefer the Minimax or the Laguna but the budget I have makes just
having the Rikon please me totally.
Mike M
On Mon, 29 Jan 2007 22:04:01 -0800, Malathan <[email protected]>
wrote:
>What about the Grizzly 513x? That was another one I was considering.
>I am leaning more towards an 18" saw rather than a 14" (with riser),
>figuring in the long run it would be better and be a better value.
>$1000 is stretching my budget though.
>
>- Clayton
>
>
>
>On Mon, 29 Jan 2007 21:06:15 -0800, Mike M
><[email protected]> wrote:
>
>>Leon is giving you good advice. I also got the Rikon 18". Went
>>through some initial problems with tracking which were resolved.
>>If your looking to never buy another bandsaw it might not be a Rikon
>>if cutting veneers is your goal. Google Leon on bearings vs guides.
>>If my budget wasn't limited I would have bought a Laguna or Min Max.
>>Yes I'm happy with my Rikon it still is doing the job I need in the
>>budget I have.
>>
>>Mike M
>>
>>On Mon, 29 Jan 2007 19:01:49 -0600, "Leon"
>><[email protected]> wrote:
>>
>>>
>>>"Malathan" <[email protected]> wrote in message
>>>news:[email protected]...
>>>>I am in the "I need a new toy" mode and am looking at a bandsaw.
>>>> Right now, I see the saw as being able to handle basic cutting and
>>>> some resawing. The resawing I can't see as ever being more than 12",
>>>> most in the 6-8" range at most. This is for a hobby, no production
>>>> work, so saw will probably be used only few times a month.
>>>>
>>>> Given this, I have been focussing on the Rikon 325 and the Rikon 345.
>>>> The 345 has a 10 degree tilt to the left, which would allow me to use
>>>> it for doing dovetails if need be (watched David Marks do this with
>>>> the tool chest he made). I do have a 220v circuit I put in past year
>>>> "just in case" I ever needed it. Being the additional cost of a
>>>> mobile base and blades, I definately can't go more than the $1000 mark
>>>> total of the saw. The rikon 325 is $750, but will get (10% off next
>>>> month for their sale day). The Rikon 345 is $1250, but on sale for
>>>> $999 right now.
>>>>
>>>> Any thoughts to these two or recommendation for other bandsaws? I
>>>> would like to get the most flexibility and power versus the cost as I
>>>> can. While many recommend larger saws such as the Laguna, those are
>>>> towards the $2000 range and far too much out of my price range or
>>>> need.
>>>>
>>>> Any recommendations and/or comments greatly appreciated.
>>>>
>>>> - Clayton
>>>
>>>For the money and a first saw IMHO the Rikon is a decent deal. It is not
>>>going to give performance near a Minimax or Laguna. It will however compete
>>>with the normal name brands.
>>>That said, I had the 18" Rikon and had problems with tracking and absolutely
>>>hated the roller guide bearings. This is not to say that Rikon is the
>>>problem here but it only comes with roller guide bearings.
>>>
Sales man at Grizzly suggested the 555x, but and somewhat uncertain
about a rizer block. With block and and mobile stand, it would be
around $730 + shipping. not bad. I am just curious as to how it
compares with other saws, such as the new Rikon 325. Rikon's is new,
so not much word out yet, but have heard some really good things about
Grizzly saws.
- Clayton
On Mon, 29 Jan 2007 20:45:42 -0600, "Will" <[email protected]> wrote:
>Grizzly G0555X
>
>
>"Malathan" <[email protected]> wrote in message
>news:[email protected]...
>>I am in the "I need a new toy" mode and am looking at a bandsaw.
>> Right now, I see the saw as being able to handle basic cutting and
>> some resawing. The resawing I can't see as ever being more than 12",
>> most in the 6-8" range at most. This is for a hobby, no production
>> work, so saw will probably be used only few times a month.
>>
>> Given this, I have been focussing on the Rikon 325 and the Rikon 345.
>> The 345 has a 10 degree tilt to the left, which would allow me to use
>> it for doing dovetails if need be (watched David Marks do this with
>> the tool chest he made). I do have a 220v circuit I put in past year
>> "just in case" I ever needed it. Being the additional cost of a
>> mobile base and blades, I definately can't go more than the $1000 mark
>> total of the saw. The rikon 325 is $750, but will get (10% off next
>> month for their sale day). The Rikon 345 is $1250, but on sale for
>> $999 right now.
>>
>> Any thoughts to these two or recommendation for other bandsaws? I
>> would like to get the most flexibility and power versus the cost as I
>> can. While many recommend larger saws such as the Laguna, those are
>> towards the $2000 range and far too much out of my price range or
>> need.
>>
>> Any recommendations and/or comments greatly appreciated.
>>
>> - Clayton
>
<[email protected]> wrote in message
news:[email protected]...
>
> Huh. I can see that happening, but why would P-matic put them on
> their saws as standard, and Carter sell them as an upgrade? Not
> arguing with you, but rather wondering about the significance of the
> issue you cite.
Roller bearings are an upgrade over the standard guides that most all band
saws had many years ago. The are an alternative to cool blocks. Again, on
paper bearings make sence. But introduce a sticky or green wood and its
sawdust and you have a mess. On many woods the roller bearings will work
fine but my experience was that with pine and oily woods the mess was
unacceptable.
I already had been dealing with a Craftsman BS for 22 years and the Rikon
with roller bearings sounded like a good upgrade. Unfortunately I found
that the upgrade was way low of my expectations.
Additionally, ceramic guides are not the end answer. If you are using very
narrow blades the cool blocks or roller bearings are probably a better
choice. Ceramic can be damaged if it comes in contact with the teeth on a
blade. Roller bearings will damage also but not as quickly.
>
> Please see the following review for an alternate opinion on roller
> bearings:
>
> http://www.newwoodworker.com/reviews/crtrlrguidrvu.html
I saw no mention of the results of cutting green or sticky wood.
Roller bearings work great at doing what they are suppose to do, up until
they get a layer of saw dust stuck to them and or the blade.
If you can swing the upgrade, I believe this would be a much better choice
over roller bearings.
http://www.lagunatools.com/index.asp?PageAction=VIEWPROD&ProdID=16&HS=1
And a video showing and explaining the Laguna guides. Large down load,
11meg.
http://www.lagunatools.com/images/guides.wmv
What about the Grizzly 513x? That was another one I was considering.
I am leaning more towards an 18" saw rather than a 14" (with riser),
figuring in the long run it would be better and be a better value.
$1000 is stretching my budget though.
- Clayton
On Mon, 29 Jan 2007 21:06:15 -0800, Mike M
<[email protected]> wrote:
>Leon is giving you good advice. I also got the Rikon 18". Went
>through some initial problems with tracking which were resolved.
>If your looking to never buy another bandsaw it might not be a Rikon
>if cutting veneers is your goal. Google Leon on bearings vs guides.
>If my budget wasn't limited I would have bought a Laguna or Min Max.
>Yes I'm happy with my Rikon it still is doing the job I need in the
>budget I have.
>
>Mike M
>
>On Mon, 29 Jan 2007 19:01:49 -0600, "Leon"
><[email protected]> wrote:
>
>>
>>"Malathan" <[email protected]> wrote in message
>>news:[email protected]...
>>>I am in the "I need a new toy" mode and am looking at a bandsaw.
>>> Right now, I see the saw as being able to handle basic cutting and
>>> some resawing. The resawing I can't see as ever being more than 12",
>>> most in the 6-8" range at most. This is for a hobby, no production
>>> work, so saw will probably be used only few times a month.
>>>
>>> Given this, I have been focussing on the Rikon 325 and the Rikon 345.
>>> The 345 has a 10 degree tilt to the left, which would allow me to use
>>> it for doing dovetails if need be (watched David Marks do this with
>>> the tool chest he made). I do have a 220v circuit I put in past year
>>> "just in case" I ever needed it. Being the additional cost of a
>>> mobile base and blades, I definately can't go more than the $1000 mark
>>> total of the saw. The rikon 325 is $750, but will get (10% off next
>>> month for their sale day). The Rikon 345 is $1250, but on sale for
>>> $999 right now.
>>>
>>> Any thoughts to these two or recommendation for other bandsaws? I
>>> would like to get the most flexibility and power versus the cost as I
>>> can. While many recommend larger saws such as the Laguna, those are
>>> towards the $2000 range and far too much out of my price range or
>>> need.
>>>
>>> Any recommendations and/or comments greatly appreciated.
>>>
>>> - Clayton
>>
>>For the money and a first saw IMHO the Rikon is a decent deal. It is not
>>going to give performance near a Minimax or Laguna. It will however compete
>>with the normal name brands.
>>That said, I had the 18" Rikon and had problems with tracking and absolutely
>>hated the roller guide bearings. This is not to say that Rikon is the
>>problem here but it only comes with roller guide bearings.
>>
In article <[email protected]>, [email protected]
says...
>
> Any thoughts to these two or recommendation for other bandsaws? I
> would like to get the most flexibility and power versus the cost as I
> can. While many recommend larger saws such as the Laguna, those are
> towards the $2000 range and far too much out of my price range or
> need.
>
> Any recommendations and/or comments greatly appreciated.
>
> - Clayton
I went through this some months ago. In the end I decided that buying an
Italian made saw I could not justify considering the price difference and my
usage (which is several times a week, but I am not a professioal woodworker).
On the other hand I looked at a lot of the cheap & nasties, and asked to do
trial runs, in most cases I ran out of the demo room.
In the end I decided to go for an 18" Jet, which is also Taiwan made, but the
production standards seem way higher than the other saws I saw. I am very very
happy with the performance; even the ball bearing guides are ok.
NB - I never clapped eyes on Rikon, Grizz or Delta, those brands are not sold
in this country, so I cannot compare them.
-P.
--
=========================================
firstname dot lastname at gmail fullstop com
"Malathan" <[email protected]> wrote in message
news:[email protected]...
> Called Grizzly. Even talked with a sales manager. They would not
> budge at all. Very firm and irresolute. That is a shame being that
> such attitudes lose them customers.
>
> - Clayton
In all fairness to Grizzly, if you are pretty much the cheapest game in town
already there is little incentive to drop the price.
Before you pull it out, try calling Rikon to see what they have to
say. Maybe they might have a solution or something. It is worth a
shot at least. Besides, waiting a night is good to cool off before
making such calls (I can vouch for that many many times) and am often
surprised by support and their helpfullness where I had expected
nothing but a wall.
- Clayton
On 30 Jan 2007 17:23:57 -0800, [email protected] wrote:
>
>Malathan wrote:
>> I have decided on the Rikon 325. Given what I will be using it for
>> and how often, think this 14" saw will do everything i want it to do
>> including some basic resawing. Also, give the fact that my local
>> Woodcraft has all power equipment on sale for 10% off, that brings it
>> down to $675. Anything else would be a $300+ jump up, which I don't
>> think would justify the benefits.
>>
>> Thank you everyone for taking time to respond. Your feedback was very
>> helpful.
>>
>> - Clayton
>
>Ummm, yeah... I don't know how to say this....
>
>Just went down to the shop to put the stand for the Rikon together,
>then the mobile base, then put the stand on the base and think about
>possibly hefting the body of the saw up onto the base.... I am a big
>boy and have carried a Jet 161/2 floor standing drill press down to
>the basement.....
>
>Then I noticed that one of the bolt holes to attach the body to the
>base was drilled off the location where the other three were. Huh.
>Intentional? Ummm, no. More like a QC problem. Damn. Would hafta
>drill it out or something as there is a nut that the bolt threads into
>welded to the base below. So no tolerance of 1/4" off. Damn. And
>that plate welded to the bottom of the saw isn't going to be swapped
>out either. Don't think I can drill it out either.
>
>When I get it back to Woodcraft, I am going to replace it with a
>Powermatic. The 14" they have on sale. Free riser block. $799 after
>rebate. $45 bucks more. Shoulda done it in the first place.
>
>Just disappointing. Mebbe check yours out afore ya lug it down to the
>basement and have to lug it back out.
>
>Maybe before you take it out of the store. Damn. I've heard of
>people having to deal with crap like this with other mfr's but I
>thought I PAID for QC.
>
>Disheartened D'ohBoy, who's gonna hafta lug that bitch outta the
>basement.
On Tue, 30 Jan 2007 10:06:08 -0600, Markem
<markem(sixoneeight)@hotmail.com> wrote:
>On Mon, 29 Jan 2007 22:04:01 -0800, Malathan <[email protected]>
>wrote:
>
>>What about the Grizzly 513x? That was another one I was considering.
>>I am leaning more towards an 18" saw rather than a 14" (with riser),
>>figuring in the long run it would be better and be a better value.
>>$1000 is stretching my budget though.
>
>If a $1000 is stretching it, but you want something bigger than 14",
>Steel City 16" bandsaw might be worth looking at.
>
>I found this listing on Ebay
>http://cgi.ebay.com/Steel-City-Tool-Works-50200-16-Industrial-Bandsaw_W0QQitemZ170076040448QQihZ007QQcategoryZ57124QQcmdZViewItem
>
>Mark
>(sixoneeight) = 618
Saw a review in either wood or finewoodworking, don't remember the
size of the band saw, but they expressed a concern on the amount of
flex in the upper blade guides.
Mike M
I have decided on the Rikon 325. Given what I will be using it for
and how often, think this 14" saw will do everything i want it to do
including some basic resawing. Also, give the fact that my local
Woodcraft has all power equipment on sale for 10% off, that brings it
down to $675. Anything else would be a $300+ jump up, which I don't
think would justify the benefits.
Thank you everyone for taking time to respond. Your feedback was very
helpful.
- Clayton
"Malathan" wrote
> Called Grizzly. Even talked with a sales manager. They would not
> budge at all. Very firm and irresolute. That is a shame being that
> such attitudes lose them customers.
>
They lose customers because they did not honor last year's sales price?
What percentage of businesses honor a christmas price in January?
Somehow or another, Grizzly will get along just fine without your business.
And they will continue to have many more sales. And they will continue to
introduce new models and phase out old ones.
Life goes on. And the Grizzly business model is doing well. In spite of your
disapproval. In fact you could say by offering good value for the dollar,
particularly on middle and top models, that the Grizzly "attitude" brings
them many new and repeat customers.
On Tue, 30 Jan 2007 19:34:40 -0800, Mike M
<[email protected]> wrote:
I wrote >>
>>If a $1000 is stretching it, but you want something bigger than 14",
>>Steel City 16" bandsaw might be worth looking at.
>Saw a review in either wood or finewoodworking, don't remember the
>size of the band saw, but they expressed a concern on the amount of
>flex in the upper blade guides.
The local (60 miles) dealer has some setup, I look at the 18" real
hard for awhile and said to my self "next time back I ask for the
power cord and some wood" they look real nice but buy it untried,
$1300 could be a big booboo. Probably bring a nice max size piece to
resaw too.
Mark
(sixoneeight) = 618
On Mon, 29 Jan 2007 22:04:01 -0800, Malathan <[email protected]>
wrote:
>What about the Grizzly 513x? That was another one I was considering.
>I am leaning more towards an 18" saw rather than a 14" (with riser),
>figuring in the long run it would be better and be a better value.
>$1000 is stretching my budget though.
If a $1000 is stretching it, but you want something bigger than 14",
Steel City 16" bandsaw might be worth looking at.
I found this listing on Ebay
http://cgi.ebay.com/Steel-City-Tool-Works-50200-16-Industrial-Bandsaw_W0QQitemZ170076040448QQihZ007QQcategoryZ57124QQcmdZViewItem
Mark
(sixoneeight) = 618
Leon is giving you good advice. I also got the Rikon 18". Went
through some initial problems with tracking which were resolved.
If your looking to never buy another bandsaw it might not be a Rikon
if cutting veneers is your goal. Google Leon on bearings vs guides.
If my budget wasn't limited I would have bought a Laguna or Min Max.
Yes I'm happy with my Rikon it still is doing the job I need in the
budget I have.
Mike M
On Mon, 29 Jan 2007 19:01:49 -0600, "Leon"
<[email protected]> wrote:
>
>"Malathan" <[email protected]> wrote in message
>news:[email protected]...
>>I am in the "I need a new toy" mode and am looking at a bandsaw.
>> Right now, I see the saw as being able to handle basic cutting and
>> some resawing. The resawing I can't see as ever being more than 12",
>> most in the 6-8" range at most. This is for a hobby, no production
>> work, so saw will probably be used only few times a month.
>>
>> Given this, I have been focussing on the Rikon 325 and the Rikon 345.
>> The 345 has a 10 degree tilt to the left, which would allow me to use
>> it for doing dovetails if need be (watched David Marks do this with
>> the tool chest he made). I do have a 220v circuit I put in past year
>> "just in case" I ever needed it. Being the additional cost of a
>> mobile base and blades, I definately can't go more than the $1000 mark
>> total of the saw. The rikon 325 is $750, but will get (10% off next
>> month for their sale day). The Rikon 345 is $1250, but on sale for
>> $999 right now.
>>
>> Any thoughts to these two or recommendation for other bandsaws? I
>> would like to get the most flexibility and power versus the cost as I
>> can. While many recommend larger saws such as the Laguna, those are
>> towards the $2000 range and far too much out of my price range or
>> need.
>>
>> Any recommendations and/or comments greatly appreciated.
>>
>> - Clayton
>
>For the money and a first saw IMHO the Rikon is a decent deal. It is not
>going to give performance near a Minimax or Laguna. It will however compete
>with the normal name brands.
>That said, I had the 18" Rikon and had problems with tracking and absolutely
>hated the roller guide bearings. This is not to say that Rikon is the
>problem here but it only comes with roller guide bearings.
>
It wasn't strictly the not budging on price, but also the poor sales
service I got from another sales person before talking with the sales
manager and the lack of response via email when questioning them about
advantages/disadvantages with specific differences in their models.
They don't have to bend over backwards, but they can at least show
"some" interest in me as a customer and willing to answer questions to
help me make a purchase decision.
- Clayton
On Tue, 30 Jan 2007 13:16:29 -0500, "Lee Michaels"
<leemichaels*nadaspam*@comcast.net> wrote:
>
>"Malathan" wrote
>> Called Grizzly. Even talked with a sales manager. They would not
>> budge at all. Very firm and irresolute. That is a shame being that
>> such attitudes lose them customers.
>>
>They lose customers because they did not honor last year's sales price?
>
>What percentage of businesses honor a christmas price in January?
>
>Somehow or another, Grizzly will get along just fine without your business.
>And they will continue to have many more sales. And they will continue to
>introduce new models and phase out old ones.
>
>Life goes on. And the Grizzly business model is doing well. In spite of your
>disapproval. In fact you could say by offering good value for the dollar,
>particularly on middle and top models, that the Grizzly "attitude" brings
>them many new and repeat customers.
>
>
>
>
>
>
Grizzly G0555X
"Malathan" <[email protected]> wrote in message
news:[email protected]...
>I am in the "I need a new toy" mode and am looking at a bandsaw.
> Right now, I see the saw as being able to handle basic cutting and
> some resawing. The resawing I can't see as ever being more than 12",
> most in the 6-8" range at most. This is for a hobby, no production
> work, so saw will probably be used only few times a month.
>
> Given this, I have been focussing on the Rikon 325 and the Rikon 345.
> The 345 has a 10 degree tilt to the left, which would allow me to use
> it for doing dovetails if need be (watched David Marks do this with
> the tool chest he made). I do have a 220v circuit I put in past year
> "just in case" I ever needed it. Being the additional cost of a
> mobile base and blades, I definately can't go more than the $1000 mark
> total of the saw. The rikon 325 is $750, but will get (10% off next
> month for their sale day). The Rikon 345 is $1250, but on sale for
> $999 right now.
>
> Any thoughts to these two or recommendation for other bandsaws? I
> would like to get the most flexibility and power versus the cost as I
> can. While many recommend larger saws such as the Laguna, those are
> towards the $2000 range and far too much out of my price range or
> need.
>
> Any recommendations and/or comments greatly appreciated.
>
> - Clayton
[email protected] wrote:
>
> Huh. I can see that happening, but why would P-matic put them on
> their saws as standard, and Carter sell them as an upgrade?
The same reason some high-end saws choose ceramic guides over ball
bearings. Not every guide is perfect in every situation. Marketing,
customer taste and perception does occasionally play into equipment
design decisions, as it may have in P-matic's case.
As for Carter, if you can sell it, you do. Remember, not every
aftermarket "upgrade" is better in every situation. Need an example?
Look no further than bandsaw blades. Some folks swear by certain
blades, others don't even see the issues the first group solves. <G>
Ball bearing guides can also have issues with narrow blades, which can
be easily corrected on block style guides by swapping a metal or ceramic
block out in favor of a carbon block.
To me the, the hot setup would be bearings that can be installed in the
same mounts as blocks, and easily and quickly swapped back and forth.