Thought I would share my first impressions of the 10" combination planer
/thicknesser I purchased recently.
My first requirement was for a thicknesser to dress boards that were
produced from re-sawing 7 1/2" x 2" pine planks. ( still have about 50.)
This would give me two 7 1/2" x 7/8 boards or three 1/2" x 7 1/2". (Approx)
Secondly, I have limited space in the workshop, - about 500 sq. ft. - and
wanted a small machine footprint.
Thirdly, my usage would be minimal and intermittent, so I didn't want to
spend any more than necessary to achieve the above.
I opted for a Chinese manufactured dual purpose machine with a three blade
cutterhead and serrated steel feed roller, purchased from a local machinery
outlet with a good reputation. Cost: AUD$1300, with three years warranty.
Delivered promptly, craned off the back of the truck on to a mobile base I'd
made for the purpose and wheeled into the workshop.
Read the assembly instructions, all required parts were there. The
assembly/operating instructions were written in good clear English, however,
they lacked sufficient detail in my opinion. Spent the first part of the day
checking capscrews and fittings, found a couple that needed tightening.
On checking table alignments, I found both the top infeed and outfeed tables
were slightly off alignment with the cutterhead and they were not precisely
co-planar. Adjustment was simple, and I cycled the height adjustment for
both infeed and outfeed several times and found the integrity of the
alignment was maintained. Everything else seemed fine.
Hooked up the dust collection and selected a piece of 3" x 3" with a
significant bow to try on the jointer.
Worked perfectly. Four passes on the jointer on the concave side and the bow
was gone. No sign of taper. Then flipped the jointer tables away, turned the
extractor hood over and set up for thickness planing. Four passes removed
the convex. The feed rate seemed well matched to the cutter. Ran a few other
different sized pieces through, with excellent results each time.
Finish was far better than I had anticipated. No snipe at all. Noise level
was far less than I had thought it would be. Chip extraction worked well.
Jointer fence is adequate, but nothing to write home about.
Conversion from jointer to thicknesser mode, or the reverse, takes less than
15 seconds. The tables are secured by simple and effective cam locks. Table
rise and fall seems precise, with no movement from set position.
So far, I am well pleased.
Tomorrow, I will remove the side covers and check out the integrity of the
chains, sprockets and bearings. - now, having said I'm happy with the
machine, sod's law dictates that I'll find a sprocket starting to chew out
or some other disaster. : )
Pics on web page.
http://www.flickr.com/photos/32473839@N02
diggerop
"diggerop" <toobusy@themoment> wrote in message
news:[email protected]...
> Thought I would share my first impressions of the 10" combination planer
> /thicknesser I purchased recently.
> Pics on web page.
>
> http://www.flickr.com/photos/32473839@N02
>
> diggerop
>
>
Took the covers off the base this morning. (Pics added.)
Chains, sprockets, bearings and pulleys were all secure. Alignment was good,
no runout evident in sprockets or pulleys. Shaft keys secure.
There is a large wheel in the centre, which has a rubber coated
circumference. Operating the lever to engage the feed brings this rubber
surface into contact with the rotating cutter shaft, thus driving the feed
rollers. Simple and effective.
Chain and sprocket size seems a bit light to me. Also, not keen on the
minimal amount of chain contact on the outfeed roller sprocket (approx
25%). Chain contact with this sprocket is maintained with a sealed roller
bearing on a spring loaded arm. As a result, the chain is as tight as a
drum. Definitely didn't like that, so I modified it by drilling another hole
in the arm approx 50% of the distance from the fulcrum as compared to the
original. It's far better than it was, but still not how I would like to see
a chain run.
My experience with chains has been that when aligned, lubricated and
properly adjusted, with slight movement at the centre of the longest span,
they will last thousands of hours.
I'll likely modify the spring system to an adjustable rod when the warranty
runs out in three years time.
Another modification would be to hinge the base cover so that I could easily
access the drive area for maintenance. Presently it requires the removal of
six self- tapping screws.
One potential problem, is what might happen in the event of a feed roller
jam. I think it's likely that the cutter shaft will spin against the rubber
on the feed drive and damage it. Or, that the lightweight chain will fail.
(Or both.) I'd rather not find out, but sod's law says I will one day. : )
Based on my very limited use so far, coupled with what I have seen on
inspection, I'm more than happy with my purchase. It suits my back yard
hobby usage and the price is right.
However, if I were earning a living from carpentry, I'd definitely be
looking for something far more robust.
diggerop