What kind of saw would you use?

"Upscale" <[email protected]> wrote in message
news:[email protected]...
>
> "JC" <[email protected]> wrote in message
>> Exactly. That's the way to go. If you don't have a router, you could use
> the
>> jig saw with a smooth cutting blade and a guide edge. G O V E R Y S L O
> W.
>> In this case patience (which I have very little of) is a virtue.
>
> Also before cutting with the jigsaw, score the Formica with the sharp edge
> of a knife. Another method is to run a piece of duct tape or something
> like
> that down the middle of the cut line which will minimize chipping, cut a
> little wide with the jigsaw, then trim the edge with a razor knife.
>
>

Yet another little trick is to heat the formica with a hair dryer before you
cut it. But, I don't recommend this one for the novice.
--
NewsProxy used here. Crossposters
and multiple addressees blocked.

JC

"JC" <[email protected]> wrote in message
> Exactly. That's the way to go. If you don't have a router, you could use
the
> jig saw with a smooth cutting blade and a guide edge. G O V E R Y S L O
W.
> In this case patience (which I have very little of) is a virtue.

Also before cutting with the jigsaw, score the Formica with the sharp edge
of a knife. Another method is to run a piece of duct tape or something like
that down the middle of the cut line which will minimize chipping, cut a
little wide with the jigsaw, then trim the edge with a razor knife.

On Mar 26, 4:39=A0pm, Frank Boettcher <[email protected]> wrote:
> On Wed, 26 Mar 2008 12:47:10 -0700 (PDT), Kevin
>
>
>
> <[email protected]> wrote:
> >My parents recently bought a new electric range for their condo, which
> >is 30" wide. =A0Unfortunately, the old range was a drop-in, so the gap
> >between the cabinets is only about 29" wide. =A0So, to make the new
> >range fit, I will need to cut back the formica countertops and the
> >vertical wooden trim boards. =A0What kind of saw would you use on this
> >job?
>
> >My thoughts:
>
> >1. Sawzall - much too brutal
> >2. 7 1/4" circular saw - will cause too much chip-out and I won't be
> >able to get close to the edges
> >3. =A0Jigsaw - best bet, but line may be a bit wiggly
> >4. =A0As-yet-unpurchased mini circular saw (5") - same issues as #2?
> >5. =A0handsaw - I get tired just thinking about it. =A0After all,
> >electrons are our friends.
>
> >The countertops and cabinetry are all sub-beautiful,so basically I'm
> >looking for the best way to make a clean straight cut without a whole
> >lot of agony.
>
> >Thanks!
>
> >Kevin
>
> I guess you've checked and determined that you can't move one of the
> cabinets an inch. =A0Maybe to much offset to the hood? =A0
>
> You can cut the trim face frame piece with a circular saw with a guide
> clamped on. =A0 I just did one, came out fine. =A0They were walnut
> stained, and I just flat blacked the cut face which is not seen
> because of the range projection.
>
> If the counters are not too long and don't turn to an L, take them
> off, take them to a countertop place and get them to trim them for
> you. =A0Usually just a few screws in the corner gussets holding them on.
>
> Frank

ZZzactly. Cut the OTHER>>> end.

Another choice is the 'down-cut' saw blades. Cuts laminate nice and
clean, but hang onto the saw...it want to ride upwards..push down on
it with authority when attempting a cut with those kinda blades. They
are specifically designed to cut laminate in that fashion. Leaves a
beautiful
edge.... go slow and steady against a straight edge. Finish off the
piece you can't cut with a Fein MultiMaster...now THERE's an excuse to
buy a wonderful tool.

On Mar 27, 8:48 am, Pat Barber <[email protected]> wrote:

> http://www.woodworkingtips.com/etips/etip022500wb.html

LMAO... there's some burning memories...

Robert

"Kevin" <[email protected]> wrote in message
> between the cabinets is only about 29" wide. So, to make the new
> range fit, I will need to cut back the formica countertops and the
> vertical wooden trim boards. What kind of saw would you use on this
> job?

Router with a straight bit running along a guide edge. The router won't be
able to get right into the back corners, but you can cut that part a little
wide with a hand saw and then trim it off with a razor knife.

In article <764e082b-f2da-4499-afe1-5e7da10f40e3
@e67g2000hsa.googlegroups.com>, [email protected] says...
> My parents recently bought a new electric range for their condo, which
> is 30" wide. Unfortunately, the old range was a drop-in, so the gap
> between the cabinets is only about 29" wide. So, to make the new
> range fit, I will need to cut back the formica countertops and the
> vertical wooden trim boards. What kind of saw would you use on this
> job?
>
> My thoughts:
>
> 1. Sawzall - much too brutal
> 2. 7 1/4" circular saw - will cause too much chip-out and I won't be
> able to get close to the edges
> 3. Jigsaw - best bet, but line may be a bit wiggly
> 4. As-yet-unpurchased mini circular saw (5") - same issues as #2?
> 5. handsaw - I get tired just thinking about it. After all,
> electrons are our friends.
>
> The countertops and cabinetry are all sub-beautiful,so basically I'm
> looking for the best way to make a clean straight cut without a whole
> lot of agony.
>
> Thanks!
>
> Kevin

I'm tempted to say measure before you buy, but really
I think you want to take it back and buy one that fits.

S.

On Mar 26, 3:17 pm, Robatoy <[email protected]> wrote:

> Finish off the
> piece you can't cut with a Fein MultiMaster...now THERE's an excuse to
> buy a wonderful tool.

You know, they have just started the TV informercials on them again.
It looks mighty tempting. They show a room that is in shambles.

Then after purchasing the Fein tool, they show what has happened to
the room after they got started with that tool. Incredible. You
wouldn't recognize the room from the before and after pics.

Apparently it paints, stains, lays flooring, installs carpet, does
interior decorating (planning maybe? can't see it as a shopping aid)
and improves the lighting in the room. Not to mention the fact that
it cuts really long flat miters on fireplace mantles as well as trim
miters accurately and with ease. I think it may install windows as
well.

I know that tool is indispensable for some things, but I never knew it
was so versatile.

I was thinking Festool stuff... but I don't know now...

Damn you late night TV!

Robert

On Mar 26, 1:47=A0pm, Kevin <[email protected]> wrote:
> My parents recently bought a new electric range for their condo, which
> is 30" wide. =A0Unfortunately, the old range was a drop-in, so the gap
> Thanks!
>
> Kevin

The above ideas look good for cutting. But have you considered a
small corner molding to hide the end of the counter? Thin Plastic in
a matching/contrasting color? Maybe a nice wood, properly finished??
If you find something, you could use the chain saw (electric, of
course) for the cut.

Hope this helps.....

http://www.woodworkingtips.com/etips/etip022500wb.html

Kevin wrote:
>
> The countertops and cabinetry are all sub-beautiful,so basically I'm
> looking for the best way to make a clean straight cut without a whole
> lot of agony.

On Wed, 26 Mar 2008 12:47:10 -0700 (PDT), Kevin
<[email protected]> wrote:

>My parents recently bought a new electric range for their condo, which
>is 30" wide. Unfortunately, the old range was a drop-in, so the gap
>between the cabinets is only about 29" wide. So, to make the new
>range fit, I will need to cut back the formica countertops and the
>vertical wooden trim boards. What kind of saw would you use on this
>job?
>
>My thoughts:
>
>1. Sawzall - much too brutal
>2. 7 1/4" circular saw - will cause too much chip-out and I won't be
>able to get close to the edges
>3. Jigsaw - best bet, but line may be a bit wiggly
>4. As-yet-unpurchased mini circular saw (5") - same issues as #2?
>5. handsaw - I get tired just thinking about it. After all,
>electrons are our friends.
>
>The countertops and cabinetry are all sub-beautiful,so basically I'm
>looking for the best way to make a clean straight cut without a whole
>lot of agony.
>
>Thanks!
>
>Kevin


I guess you've checked and determined that you can't move one of the
cabinets an inch. Maybe to much offset to the hood?

You can cut the trim face frame piece with a circular saw with a guide
clamped on. I just did one, came out fine. They were walnut
stained, and I just flat blacked the cut face which is not seen
because of the range projection.

If the counters are not too long and don't turn to an L, take them
off, take them to a countertop place and get them to trim them for
you. Usually just a few screws in the corner gussets holding them on.

Frank

"Upscale" <[email protected]> wrote in message
news:[email protected]...
>
> "Kevin" <[email protected]> wrote in message
>> between the cabinets is only about 29" wide. So, to make the new
>> range fit, I will need to cut back the formica countertops and the
>> vertical wooden trim boards. What kind of saw would you use on this
>> job?
>
> Router with a straight bit running along a guide edge. The router won't be
> able to get right into the back corners, but you can cut that part a
> little
> wide with a hand saw and then trim it off with a razor knife.
>
>

Exactly. That's the way to go. If you don't have a router, you could use the
jig saw with a smooth cutting blade and a guide edge. G O V E R Y S L O W.
In this case patience (which I have very little of) is a virtue.
--
NewsProxy used here. Crossposters
and multiple addressees blocked.

JC

"Kevin" <[email protected]> wrote in message
news:764e082b-f2da-4499-afe1-5e7da10f40e3@e67g2000hsa.googlegroups.com...
> My parents recently bought a new electric range for their condo, which
> is 30" wide. Unfortunately, the old range was a drop-in, so the gap
> between the cabinets is only about 29" wide. So, to make the new
> range fit, I will need to cut back the formica countertops and the
> vertical wooden trim boards. What kind of saw would you use on this
> job?
>
I had the exact same problem once at my old house, I taped it up and used a
jig saw. Went through a bunch of blades, Smoothed the edges with a file and
a utility knife,

It wasn't perfect, but it worked.