Nightstand Drawers

OFWW <[email protected]> wrote:
> On Tue, 2 Feb 2016 18:40:38 -0600, Leon <lcb11211@swbelldotnet> wrote:
>
>> On 1/31/2016 3:44 PM, Leon wrote:
>>
>> So my customer got the pulls that she wanted to put on the drawer fronts
>> and I could proceed.
>>
>> These are inset drawers and that fact always adds a degree of difficulty
>> over overlay drawer fronts.
>>
>> A couple of years ago I applied a bit of unused knowledge to make this
>> process much easier.
>>
>> Shimming is a must but attaching the false fronts to the mounted drawers
>> is always a bit tough. In fact there are special washer head screws for
>> mounting drawer fronts through over sized holes to allow for
>> readjustment after attaching. The typical procedure is to put screws
>> into the front of the drawer from the inside and let the points of the
>> screws stick out just a bit. Then press the outer false drawer front
>> into the screw points, remove the front, locate the dimples made by the
>> screw points, predrill shallow holes where there were indentations, line
>> up the front with the screws, drive home the screws. And typically the
>> drawer front is not perfectly placed.
>>
>> Now,,,,,,I wait until I have the pulls before I mount the false fronts.
>> I drill the holes for the pulls into the false fronts only, place the
>> false drawer front into position and place pocket hole screws through
>> the false front drawer pull holes into the drawer, snugly. Those screws
>> hold the false drawer front and allow you to open the drawer and add the
>> remaining screws from the inside with out all of the steps listed above.
>> Remove the pocket holes and finish drilling the holes for the pulls
>> through the inner drawer.
>>
>> Anyway,,,
>>
>> The process with shims.
>>
>> https://www.flickr.com/photos/lcb11211/24664669262/in/dateposted-public/
>>
>> And the result, with no need for any adjustments and the pocket holes
>> removed.
>>
>> https://www.flickr.com/photos/lcb11211/24756262116/in/dateposted-public/
>>
>>
>>
>
> That's looking mighty good.
>
> I've been following yours and Karl's advice, been spending time in
> Sketchup, which is why I've not been online but for short spurts.
>
> I'll be commenting on previous posts for the goodies I have learned
> soon.
>
> Those drawers look almost tight enough that if high humidity hung
> around long they'd swell up and become self locking drawers. ;)
>

If the cabinets were going to be in an uncontrolled environment I might be
concerned about fit later on. But I too will be sealing with stain and
varnish which will aid in stability.
The drawer fronts have a 1/16" gap all of the way around.

On Sun, 31 Jan 2016 15:44:22 -0600, Leon <lcb11211@swbelldotnet>
wrote:

>I finished the hard part of the drawers, building them.
>I build them out of Baltic birch and used rabbeted corners reinforced
>with Domino floating tenons. I have built a few hundred drawers this
>way and it seems I am still learning how to stream line this process.
>
>The pieces,
>
>https://www.flickr.com/photos/lcb11211/24382723850/in/dateposted-public/
>
>Glued up,
>
>https://www.flickr.com/photos/lcb11211/24050071344/in/dateposted-public/
>
>Domino floating tenons installed and the drawers mounted in the cabinets.
>

Are those installed after the drawers are glued up?

>https://www.flickr.com/photos/lcb11211/24370070979/in/dateposted-public/
>
>And the solid drawer fronts ready for stain. I cut the bevels on the TS
>and then sanded.
>
>https://www.flickr.com/photos/lcb11211/24109563244/in/dateposted-public/

Very nice!

<[email protected]> wrote in message
news:[email protected]...
>snip
> Seriously, I have thought for some time you should contact Festool and be
> their Domino guy. I am not being facetious! I only know a couple of guys
> that have that tool, but I heard through the grapevine somewhere that the
> Domino is a great seller for Festool. Yet, I never hear or see anyone
> using that tool except you and never see any examples of its use anywhere!
>
> Snipped
>
> I can easily see you in a gremlin green van touring Texas as "Dan Domino"
> preaching the gospel of mortised spline joinery to the masses. Not
> kidding, Leon. I have never seen more creative work with that tool than
> you do.
>
> Robert
>
From a pure marketing perspective, you easily tie in the Domino mastery with
current television shows. And there has been a glut of new shows recently
with comic book heroes. Soooooooooo....., A Festool costume with a cape
would be appropriate. Can you see Leon as Domino Man, super hero? He would
have two cordless dominos in holsters strapped to his thighs and a Festool
dust extractor on a back pack. I assume that the cape would go over the
dust extractor.

He could fly into various locations, throughout Texas, suspended under a
large Festool drone. He would land, give a quick Domino drawer lessons,
then fly off into the sunset. Maybe one of the home channels would make a
reality series out of it. And it could even feature some good, old Texas
barbeque!

I think this idea would work! Hey Leon, should I sit down and write a
formal proposal to create a new persona for you as Domino Man, super hero?
We could pitch it to Festool. Their advertising budget should easily cover
the cost of creating a super hero. And I would be on board for a reasonable
12% of the budget for an "origination" fee.

Come on Leon, think outside of the box. This could work! ;-)

"Lee Michaels" <leemichaels*nadaspam* at comcast dot net> wrote in
news:[email protected]:

> From a pure marketing perspective, you easily tie in the Domino
> mastery with current television shows. And there has been a glut of
> new shows recently with comic book heroes. Soooooooooo....., A
> Festool costume with a cape would be appropriate. Can you see Leon as
> Domino Man, super hero? He would have two cordless dominos in
> holsters strapped to his thighs and a Festool dust extractor on a back
> pack. I assume that the cape would go over the dust extractor.
>
> He could fly into various locations, throughout Texas, suspended under
> a large Festool drone. He would land, give a quick Domino drawer
> lessons, then fly off into the sunset. Maybe one of the home channels
> would make a reality series out of it. And it could even feature some
> good, old Texas barbeque!
>
> I think this idea would work! Hey Leon, should I sit down and write a
> formal proposal to create a new persona for you as Domino Man, super
> hero? We could pitch it to Festool. Their advertising budget should
> easily cover the cost of creating a super hero. And I would be on
> board for a reasonable 12% of the budget for an "origination" fee.
>
> Come on Leon, think outside of the box. This could work! ;-)
>

Opening title sequence: We see Domino Man set down his Domino cutter,
setting the first in a sequence of dominoes to fall. As they fall, they
go past a variety of projects that we'll see later assembled with
Dominos.

Closing sequence: We see Domino Man enjoying some barbeque as the UPS man
pulls up with a surprise package. Domino Man offers the UPS man some
barbeque as he opens the package to see what's inside it... more Dominos!

All we gotta do is get Leon to fill in the middle!

Puckdropper

On Wed, 3 Feb 2016 14:32:20 -0600, Leon <lcb11211@swbelldotnet> wrote:

>On 2/3/2016 2:08 PM, OFWW wrote:
>> On Wed, 3 Feb 2016 07:50:42 -0600, Leon <[email protected]> wrote:
>>
>>> OFWW <[email protected]> wrote:
>>>> On Tue, 2 Feb 2016 18:40:38 -0600, Leon <lcb11211@swbelldotnet> wrote:
>>>>
>>>>> On 1/31/2016 3:44 PM, Leon wrote:
>>>>>
>>>>> So my customer got the pulls that she wanted to put on the drawer fronts
>>>>> and I could proceed.
>>>>>
>>>>> These are inset drawers and that fact always adds a degree of difficulty
>>>>> over overlay drawer fronts.
>>>>>
>>>>> A couple of years ago I applied a bit of unused knowledge to make this
>>>>> process much easier.
>>>>>
>>>>> Shimming is a must but attaching the false fronts to the mounted drawers
>>>>> is always a bit tough. In fact there are special washer head screws for
>>>>> mounting drawer fronts through over sized holes to allow for
>>>>> readjustment after attaching. The typical procedure is to put screws
>>>>> into the front of the drawer from the inside and let the points of the
>>>>> screws stick out just a bit. Then press the outer false drawer front
>>>>> into the screw points, remove the front, locate the dimples made by the
>>>>> screw points, predrill shallow holes where there were indentations, line
>>>>> up the front with the screws, drive home the screws. And typically the
>>>>> drawer front is not perfectly placed.
>>>>>
>>>>> Now,,,,,,I wait until I have the pulls before I mount the false fronts.
>>>>> I drill the holes for the pulls into the false fronts only, place the
>>>>> false drawer front into position and place pocket hole screws through
>>>>> the false front drawer pull holes into the drawer, snugly. Those screws
>>>>> hold the false drawer front and allow you to open the drawer and add the
>>>>> remaining screws from the inside with out all of the steps listed above.
>>>>> Remove the pocket holes and finish drilling the holes for the pulls
>>>>> through the inner drawer.
>>>>>
>>>>> Anyway,,,
>>>>>
>>>>> The process with shims.
>>>>>
>>>>> https://www.flickr.com/photos/lcb11211/24664669262/in/dateposted-public/
>>>>>
>>>>> And the result, with no need for any adjustments and the pocket holes
>>>>> removed.
>>>>>
>>>>> https://www.flickr.com/photos/lcb11211/24756262116/in/dateposted-public/
>>>>>
>>>>>
>>>>>
>>>>
>>>> That's looking mighty good.
>>>>
>>>> I've been following yours and Karl's advice, been spending time in
>>>> Sketchup, which is why I've not been online but for short spurts.
>>>>
>>>> I'll be commenting on previous posts for the goodies I have learned
>>>> soon.
>>>>
>>>> Those drawers look almost tight enough that if high humidity hung
>>>> around long they'd swell up and become self locking drawers. ;)
>>>>
>>>
>>> If the cabinets were going to be in an uncontrolled environment I might be
>>> concerned about fit later on. But I too will be sealing with stain and
>>> varnish which will aid in stability.
>>> The drawer fronts have a 1/16" gap all of the way around.
>>
>> Actually I meant that as a joke, seeing as they fit so very well.
>> Sorry for the confusion.
>
>Yeah, I saw the smiley face. ;~)
>
>I just wanted to explain a bit further my reasoning and spec's. ;~)
>
>>
>> I had watched a video on making cabinet doors, and the door style he
>> was the proudest of was doors that fit like your drawer faces do. He
>> said it was a sign of a true craftsman.
>>
>
>You do have to pay attention when using inset doors and drawers as
>opposed to overlay. Square is a must.
>
>Here are a couple of examples of inset doors and drawers.
>
>I built this Murphy bed and side towers 5 years ago for a customer..
>
>https://www.flickr.com/photos/lcb11211/5807616639/in/dateposted-public/
>

You know, Murphy beds have really improved, and what a space saver.
Nothing can dual purpose a room like that, and most children's rooms
should be set up that way. I saw some a year or so ago, a couple even
a bunk bed arrangement. I've been considering putting one in a spare
bedroom.

>And Our bedroom 6 years ago... It is now in a newer home. I thought I
>would never have to move it. ;~(
>
>https://www.flickr.com/photos/lcb11211/4436685682/in/dateposted-public/
>
>The bed and tower have a total of 24 drawers. 18 under the bed.
>

I didn't show my wife those pictures, got more than enough to do at
the moment. :)

That must have kept you busy for quite a while.

>https://www.flickr.com/photos/lcb11211/4436686012/in/dateposted-public/

Not to detract from the post, but in looking at your photo's I saw
this stunning piece of beauty!

https://www.flickr.com/photos/lcb11211/4332857960/in/dateposted-public/

Is there a matching one to go with it?

Something that looks like that needs to be openly displayed.

When you build your drawers that way, they always look so clean and precise=
. I like that look a lot, and no doubt they are probably just shy of bomb p=
roof.

Seriously, I have thought for some time you should contact Festool and be t=
heir Domino guy. I am not being facetious! I only know a couple of guys t=
hat have that tool, but I heard through the grapevine somewhere that the Do=
mino is a great seller for Festool. Yet, I never hear or see anyone using =
that tool except you and never see any examples of its use anywhere!

Kathy and I will saddle up about once a year and get out of town and go to =
some of the towns around here that are in the "The Hill Country" where ther=
e are some artist communities. The artists are different every time we go =
so we have seen quite a few furniture and cabinet builders, restorers, "one=
off" makers, etc. We go north one year, then the next year we go northeas=
t, so we get the Texas Furniture Makers annual show sometimes, the Fredrick=
sburg Arts and Crafts Show, the same in Bandera and even one in Blanco.

Out of all the craftsmen we see that turn out easily produced pieces to the=
guy that has a custom wet bat in progress at his shop, I have never seen o=
ne Domino. Like you, it is a machine they could truly use on just about ev=
ery project. Yet every one of the folks I have talked to over the years th=
at owns one of those shops has never used a Domino and in most cases, don't=
know what they are.

I can easily see you in a gremlin green van touring Texas as "Dan Domino" p=
reaching the gospel of mortised spline joinery to the masses. Not kidding,=
Leon. I have never seen more creative work with that tool than you do.

Robert

On Tue, 2 Feb 2016 18:40:38 -0600, Leon <lcb11211@swbelldotnet> wrote:

>On 1/31/2016 3:44 PM, Leon wrote:
>
>So my customer got the pulls that she wanted to put on the drawer fronts
>and I could proceed.
>
>These are inset drawers and that fact always adds a degree of difficulty
>over overlay drawer fronts.
>
>A couple of years ago I applied a bit of unused knowledge to make this
>process much easier.
>
>Shimming is a must but attaching the false fronts to the mounted drawers
>is always a bit tough. In fact there are special washer head screws for
>mounting drawer fronts through over sized holes to allow for
>readjustment after attaching. The typical procedure is to put screws
>into the front of the drawer from the inside and let the points of the
>screws stick out just a bit. Then press the outer false drawer front
>into the screw points, remove the front, locate the dimples made by the
>screw points, predrill shallow holes where there were indentations, line
>up the front with the screws, drive home the screws. And typically the
>drawer front is not perfectly placed.
>
>Now,,,,,,I wait until I have the pulls before I mount the false fronts.
>I drill the holes for the pulls into the false fronts only, place the
>false drawer front into position and place pocket hole screws through
>the false front drawer pull holes into the drawer, snugly. Those screws
>hold the false drawer front and allow you to open the drawer and add the
>remaining screws from the inside with out all of the steps listed above.
> Remove the pocket holes and finish drilling the holes for the pulls
>through the inner drawer.
>
>Anyway,,,
>
>The process with shims.
>
>https://www.flickr.com/photos/lcb11211/24664669262/in/dateposted-public/
>
>And the result, with no need for any adjustments and the pocket holes
>removed.
>
>https://www.flickr.com/photos/lcb11211/24756262116/in/dateposted-public/
>
>
>

That's looking mighty good.

I've been following yours and Karl's advice, been spending time in
Sketchup, which is why I've not been online but for short spurts.

I'll be commenting on previous posts for the goodies I have learned
soon.

Those drawers look almost tight enough that if high humidity hung
around long they'd swell up and become self locking drawers. ;)

On 2/2/2016 11:33 AM, [email protected] wrote:
> When you build your drawers that way, they always look so clean and
> precise. I like that look a lot, and no doubt they are probably just
> shy of bomb proof.

Thank you Robert.
They are pretty attractive but a shade less than DT joints and or box
joints.

>
> Seriously, I have thought for some time you should contact Festool
> and be their Domino guy. I am not being facetious! I only know a
> couple of guys that have that tool, but I heard through the grapevine
> somewhere that the Domino is a great seller for Festool. Yet, I
> never hear or see anyone using that tool except you and never see any
> examples of its use anywhere!

Well I think the reps do that and or the stores should be capable of
demonstrating things to do with the Domino. The Domino was my first
tool from Festool, it and the Vac.
I found that making slots, for screws to slip in, with the Domino is
pretty cool too. You know when you have a wide solid wood panel that
needs to be attached to allow for movement.

https://www.flickr.com/photos/lcb11211/12353851794/in/dateposted-public/




> Kathy and I will saddle up about once a year and get out of town and
> go to some of the towns around here that are in the "The Hill
> Country" where there are some artist communities. The artists are
> different every time we go so we have seen quite a few furniture and
> cabinet builders, restorers, "one off" makers, etc. We go north one
> year, then the next year we go northeast, so we get the Texas
> Furniture Makers annual show sometimes, the Fredricksburg Arts and
> Crafts Show, the same in Bandera and even one in Blanco.

Kim and I did the Kerrville wood working thing in November a few years
back. There is all kinds of cool stuff going on.


>
> Out of all the craftsmen we see that turn out easily produced pieces
> to the guy that has a custom wet bat in progress at his shop, I have
> never seen one Domino. Like you, it is a machine they could truly
> use on just about every project. Yet every one of the folks I have
> talked to over the years that owns one of those shops has never used
> a Domino and in most cases, don't know what they are.

A little surprising.


>
> I can easily see you in a gremlin green van touring Texas as "Dan
> Domino" preaching the gospel of mortised spline joinery to the
> masses. Not kidding, Leon. I have never seen more creative work
> with that tool than you do.
>
> Robert
>

Thank you Robert. ;~)

On 2/2/2016 11:33 AM, [email protected] wrote:
> When you build your drawers that way, they always look so clean and precise. I like that look a lot, and no doubt they are probably just shy of bomb proof.
>
> Seriously, I have thought for some time you should contact Festool and be their Domino guy. I am not being facetious! I only know a couple of guys that have that tool, but I heard through the grapevine somewhere that the Domino is a great seller for Festool. Yet, I never hear or see anyone using that tool except you and never see any examples of its use anywhere!
>
> Kathy and I will saddle up about once a year and get out of town and go to some of the towns around here that are in the "The Hill Country" where there are some artist communities. The artists are different every time we go so we have seen quite a few furniture and cabinet builders, restorers, "one off" makers, etc. We go north one year, then the next year we go northeast, so we get the Texas Furniture Makers annual show sometimes, the Fredricksburg Arts and Crafts Show, the same in Bandera and even one in Blanco.
>
> Out of all the craftsmen we see that turn out easily produced pieces to the guy that has a custom wet bat in progress at his shop, I have never seen one Domino. Like you, it is a machine they could truly use on just about every project. Yet every one of the folks I have talked to over the years that owns one of those shops has never used a Domino and in most cases, don't know what they are.
>
> I can easily see you in a gremlin green van touring Texas as "Dan Domino" preaching the gospel of mortised spline joinery to the masses. Not kidding, Leon. I have never seen more creative work with that tool than you do.
>
> Robert
>


See what you started??? LOL

On 2/2/2016 2:44 PM, Lee Michaels wrote:
>
>
> <[email protected]> wrote in message
> news:[email protected]...
>> snip
>> Seriously, I have thought for some time you should contact Festool and
>> be their Domino guy. I am not being facetious! I only know a couple
>> of guys that have that tool, but I heard through the grapevine
>> somewhere that the Domino is a great seller for Festool. Yet, I never
>> hear or see anyone using that tool except you and never see any
>> examples of its use anywhere!
>>
> > Snipped
>>
>> I can easily see you in a gremlin green van touring Texas as "Dan
>> Domino" preaching the gospel of mortised spline joinery to the
>> masses. Not kidding, Leon. I have never seen more creative work with
>> that tool than you do.
>>
>> Robert
>>
> From a pure marketing perspective, you easily tie in the Domino mastery
> with current television shows. And there has been a glut of new shows
> recently with comic book heroes. Soooooooooo....., A Festool costume
> with a cape would be appropriate. Can you see Leon as Domino Man, super
> hero? He would have two cordless dominos in holsters strapped to his
> thighs and a Festool dust extractor on a back pack. I assume that the
> cape would go over the dust extractor.
>
> He could fly into various locations, throughout Texas, suspended under a
> large Festool drone. He would land, give a quick Domino drawer lessons,
> then fly off into the sunset. Maybe one of the home channels would make
> a reality series out of it. And it could even feature some good, old
> Texas barbeque!
>
> I think this idea would work! Hey Leon, should I sit down and write a
> formal proposal to create a new persona for you as Domino Man, super
> hero? We could pitch it to Festool. Their advertising budget should
> easily cover the cost of creating a super hero. And I would be on board
> for a reasonable 12% of the budget for an "origination" fee.
>
> Come on Leon, think outside of the box. This could work! ;-)
>
>
>
I'm game! Now sell it! LOL

On 2/2/2016 3:04 PM, Puckdropper wrote:
> "Lee Michaels" <leemichaels*nadaspam* at comcast dot net> wrote in
> news:[email protected]:
>
>> From a pure marketing perspective, you easily tie in the Domino
>> mastery with current television shows. And there has been a glut of
>> new shows recently with comic book heroes. Soooooooooo....., A
>> Festool costume with a cape would be appropriate. Can you see Leon as
>> Domino Man, super hero? He would have two cordless dominos in
>> holsters strapped to his thighs and a Festool dust extractor on a back
>> pack. I assume that the cape would go over the dust extractor.
>>
>> He could fly into various locations, throughout Texas, suspended under
>> a large Festool drone. He would land, give a quick Domino drawer
>> lessons, then fly off into the sunset. Maybe one of the home channels
>> would make a reality series out of it. And it could even feature some
>> good, old Texas barbeque!
>>
>> I think this idea would work! Hey Leon, should I sit down and write a
>> formal proposal to create a new persona for you as Domino Man, super
>> hero? We could pitch it to Festool. Their advertising budget should
>> easily cover the cost of creating a super hero. And I would be on
>> board for a reasonable 12% of the budget for an "origination" fee.
>>
>> Come on Leon, think outside of the box. This could work! ;-)
>>
>
> Opening title sequence: We see Domino Man set down his Domino cutter,
> setting the first in a sequence of dominoes to fall. As they fall, they
> go past a variety of projects that we'll see later assembled with
> Dominos.
>
> Closing sequence: We see Domino Man enjoying some barbeque as the UPS man
> pulls up with a surprise package. Domino Man offers the UPS man some
> barbeque as he opens the package to see what's inside it... more Dominos!
>
> All we gotta do is get Leon to fill in the middle!
>
> Puckdropper
>


You got it allllllll figgered out. LOL

On 1/31/2016 3:44 PM, Leon wrote:

So my customer got the pulls that she wanted to put on the drawer fronts
and I could proceed.

These are inset drawers and that fact always adds a degree of difficulty
over overlay drawer fronts.

A couple of years ago I applied a bit of unused knowledge to make this
process much easier.

Shimming is a must but attaching the false fronts to the mounted drawers
is always a bit tough. In fact there are special washer head screws for
mounting drawer fronts through over sized holes to allow for
readjustment after attaching. The typical procedure is to put screws
into the front of the drawer from the inside and let the points of the
screws stick out just a bit. Then press the outer false drawer front
into the screw points, remove the front, locate the dimples made by the
screw points, predrill shallow holes where there were indentations, line
up the front with the screws, drive home the screws. And typically the
drawer front is not perfectly placed.

Now,,,,,,I wait until I have the pulls before I mount the false fronts.
I drill the holes for the pulls into the false fronts only, place the
false drawer front into position and place pocket hole screws through
the false front drawer pull holes into the drawer, snugly. Those screws
hold the false drawer front and allow you to open the drawer and add the
remaining screws from the inside with out all of the steps listed above.
Remove the pocket holes and finish drilling the holes for the pulls
through the inner drawer.

Anyway,,,

The process with shims.

https://www.flickr.com/photos/lcb11211/24664669262/in/dateposted-public/

And the result, with no need for any adjustments and the pocket holes
removed.

https://www.flickr.com/photos/lcb11211/24756262116/in/dateposted-public/

On 1/31/2016 3:44 PM, Leon wrote:
> I finished the hard part of the drawers, building them.
> I build them out of Baltic birch and used rabbeted corners reinforced
> with Domino floating tenons. I have built a few hundred drawers this
> way and it seems I am still learning how to stream line this process.


Ah yes, the infamous "Domino Drawers" ... looking good, as usual.

--
eWoodShop: www.eWoodShop.com
Wood Shop: www.e-WoodShop.net
https://www.google.com/+eWoodShop
https://plus.google.com/+KarlCaillouet/posts
http://www.custommade.com/by/ewoodshop/
KarlCaillouet@ (the obvious)

On 2/4/2016 2:08 PM, Swingman wrote:
> On 2/4/2016 1:32 PM, OFWW wrote:
>
>> https://www.flickr.com/photos/lcb11211/4332857960/in/dateposted-public/
>>
>> Is there a matching one to go with it?
>>
>> Something that looks like that needs to be openly displayed.
>
> Good eye.
>
> I first saw that years ago and will never forget how stunning I also
> thought it was. At the time using contrasting woods was just getting a
> lot of attention on TV woodworking shows ... Leon out did them all.

Wasn't that when I first caught your eye, partner. LOL

>
> And, there is also a gorgeous, large jewelry box he made for Kim of
> spalted wood, and a glass display case for a client, and a "Texas" desk
> that are notable pieces of woodworking.
>
> Keep this up and his heads gonna swell bigger than ever ... :)
>


Good thing I wear a one size fits all cap!

On 2/5/2016 3:56 PM, Swingman wrote:
> On 2/5/2016 8:47 AM, Leon wrote:
>
>> You should get him to show you a picture of his Canasta Card holder with
>> Domino kick stand. ;~)
>
> Too bad we can't get royalties on SketchUp Models.
>
> Since I never look after occasionally uploading stuff to the 3D
> Warehouse (always out of the altruistic goodness of my heart, doncha
> know) I didn't even know you could get this info:
>
> Just noticed my kitchen island model we installed in the straw bale
> house in 2009 has been downloaded 3,748 times.
>
> https://3dwarehouse.sketchup.com/model.html?id=60dc0155e1dffd87b2c2cd006d206129
>
>
> And my Arts and Crafts Sofa table, I made for my living room, 3,210 times.
>
> https://3dwarehouse.sketchup.com/model.html?id=bdc159bdb0147e2d54f10b531fe5914c
>
>
> Jeeezzzusss ... where's my royalties, ferrcrssiskaes. LOL
>


Jeepers, your drawings have gone viral! ;~)

On Thu, 4 Feb 2016 14:08:55 -0600, Swingman <[email protected]> wrote:

>On 2/4/2016 1:32 PM, OFWW wrote:
>
>> https://www.flickr.com/photos/lcb11211/4332857960/in/dateposted-public/
>>
>> Is there a matching one to go with it?
>>
>> Something that looks like that needs to be openly displayed.
>
>Good eye.
>
>I first saw that years ago and will never forget how stunning I also
>thought it was. At the time using contrasting woods was just getting a
>lot of attention on TV woodworking shows ... Leon out did them all.
>
>And, there is also a gorgeous, large jewelry box he made for Kim of
>spalted wood, and a glass display case for a client, and a "Texas" desk
>that are notable pieces of woodworking.
>
>Keep this up and his heads gonna swell bigger than ever ... :)

Well,... Both of you men have a right and history to feel that at
least once in a while. Neither of you rest on your laurels but seem to
use that for your standard impelling you to do better. A good work
ethic with creative skills goes far.

On 2/4/2016 1:32 PM, OFWW wrote:
> On Wed, 3 Feb 2016 14:32:20 -0600, Leon <lcb11211@swbelldotnet> wrote:
>
>> On 2/3/2016 2:08 PM, OFWW wrote:
>>> On Wed, 3 Feb 2016 07:50:42 -0600, Leon <[email protected]> wrote:
>>>
>>>> OFWW <[email protected]> wrote:
>>>>> On Tue, 2 Feb 2016 18:40:38 -0600, Leon <lcb11211@swbelldotnet> wrote:
>>>>>
>>>>>> On 1/31/2016 3:44 PM, Leon wrote:
>>>>>>
>>>>>> So my customer got the pulls that she wanted to put on the drawer fronts
>>>>>> and I could proceed.
>>>>>>
>>>>>> These are inset drawers and that fact always adds a degree of difficulty
>>>>>> over overlay drawer fronts.
>>>>>>
>>>>>> A couple of years ago I applied a bit of unused knowledge to make this
>>>>>> process much easier.
>>>>>>
>>>>>> Shimming is a must but attaching the false fronts to the mounted drawers
>>>>>> is always a bit tough. In fact there are special washer head screws for
>>>>>> mounting drawer fronts through over sized holes to allow for
>>>>>> readjustment after attaching. The typical procedure is to put screws
>>>>>> into the front of the drawer from the inside and let the points of the
>>>>>> screws stick out just a bit. Then press the outer false drawer front
>>>>>> into the screw points, remove the front, locate the dimples made by the
>>>>>> screw points, predrill shallow holes where there were indentations, line
>>>>>> up the front with the screws, drive home the screws. And typically the
>>>>>> drawer front is not perfectly placed.
>>>>>>
>>>>>> Now,,,,,,I wait until I have the pulls before I mount the false fronts.
>>>>>> I drill the holes for the pulls into the false fronts only, place the
>>>>>> false drawer front into position and place pocket hole screws through
>>>>>> the false front drawer pull holes into the drawer, snugly. Those screws
>>>>>> hold the false drawer front and allow you to open the drawer and add the
>>>>>> remaining screws from the inside with out all of the steps listed above.
>>>>>> Remove the pocket holes and finish drilling the holes for the pulls
>>>>>> through the inner drawer.
>>>>>>
>>>>>> Anyway,,,
>>>>>>
>>>>>> The process with shims.
>>>>>>
>>>>>> https://www.flickr.com/photos/lcb11211/24664669262/in/dateposted-public/
>>>>>>
>>>>>> And the result, with no need for any adjustments and the pocket holes
>>>>>> removed.
>>>>>>
>>>>>> https://www.flickr.com/photos/lcb11211/24756262116/in/dateposted-public/
>>>>>>
>>>>>>
>>>>>>
>>>>>
>>>>> That's looking mighty good.
>>>>>
>>>>> I've been following yours and Karl's advice, been spending time in
>>>>> Sketchup, which is why I've not been online but for short spurts.
>>>>>
>>>>> I'll be commenting on previous posts for the goodies I have learned
>>>>> soon.
>>>>>
>>>>> Those drawers look almost tight enough that if high humidity hung
>>>>> around long they'd swell up and become self locking drawers. ;)
>>>>>
>>>>
>>>> If the cabinets were going to be in an uncontrolled environment I might be
>>>> concerned about fit later on. But I too will be sealing with stain and
>>>> varnish which will aid in stability.
>>>> The drawer fronts have a 1/16" gap all of the way around.
>>>
>>> Actually I meant that as a joke, seeing as they fit so very well.
>>> Sorry for the confusion.
>>
>> Yeah, I saw the smiley face. ;~)
>>
>> I just wanted to explain a bit further my reasoning and spec's. ;~)
>>
>>>
>>> I had watched a video on making cabinet doors, and the door style he
>>> was the proudest of was doors that fit like your drawer faces do. He
>>> said it was a sign of a true craftsman.
>>>
>>
>> You do have to pay attention when using inset doors and drawers as
>> opposed to overlay. Square is a must.
>>
>> Here are a couple of examples of inset doors and drawers.
>>
>> I built this Murphy bed and side towers 5 years ago for a customer..
>>
>> https://www.flickr.com/photos/lcb11211/5807616639/in/dateposted-public/
>>
>
> You know, Murphy beds have really improved, and what a space saver.
> Nothing can dual purpose a room like that, and most children's rooms
> should be set up that way. I saw some a year or so ago, a couple even
> a bunk bed arrangement. I've been considering putting one in a spare
> bedroom.

And I can point you towards the hardware supplier for that too. ;~)
IIRC Rockler sells for that company too.



>
>> And Our bedroom 6 years ago... It is now in a newer home. I thought I
>> would never have to move it. ;~(
>>
>> https://www.flickr.com/photos/lcb11211/4436685682/in/dateposted-public/
>>
>> The bed and tower have a total of 24 drawers. 18 under the bed.
>>
>
> I didn't show my wife those pictures, got more than enough to do at
> the moment. :)
>
> That must have kept you busy for quite a while.

About 12 weeks.

>
>> https://www.flickr.com/photos/lcb11211/4436686012/in/dateposted-public/
>
> Not to detract from the post, but in looking at your photo's I saw
> this stunning piece of beauty!


LOL, Thank you. Those were a labor of love, I built a pair for my
sister and BIL. They had a walnut chest of drawers and a walnut dresser
built by Waterford, IIRC. They wanted me to build night stands to
match. That tested my talents. The tricky parts were the feet and the
columns on the corners. I actually cut the columns "round" on the table
saw. I spent an afternoon doing that.

AND I wished I had Sketchup for the design, instead I was still using
AutoCAD LT.


>
> https://www.flickr.com/photos/lcb11211/4332857960/in/dateposted-public/
>
> Is there a matching one to go with it?

There were a pair.

>
> Something that looks like that needs to be openly displayed.
>
;~)

On 2/4/2016 1:32 PM, OFWW wrote:

> https://www.flickr.com/photos/lcb11211/4332857960/in/dateposted-public/
>
> Is there a matching one to go with it?
>
> Something that looks like that needs to be openly displayed.

Good eye.

I first saw that years ago and will never forget how stunning I also
thought it was. At the time using contrasting woods was just getting a
lot of attention on TV woodworking shows ... Leon out did them all.

And, there is also a gorgeous, large jewelry box he made for Kim of
spalted wood, and a glass display case for a client, and a "Texas" desk
that are notable pieces of woodworking.

Keep this up and his heads gonna swell bigger than ever ... :)

--
eWoodShop: www.eWoodShop.com
Wood Shop: www.e-WoodShop.net
https://www.google.com/+eWoodShop
https://plus.google.com/+KarlCaillouet/posts
http://www.custommade.com/by/ewoodshop/
KarlCaillouet@ (the obvious)

On Wed, 3 Feb 2016 07:50:42 -0600, Leon <[email protected]> wrote:

>OFWW <[email protected]> wrote:
>> On Tue, 2 Feb 2016 18:40:38 -0600, Leon <lcb11211@swbelldotnet> wrote:
>>
>>> On 1/31/2016 3:44 PM, Leon wrote:
>>>
>>> So my customer got the pulls that she wanted to put on the drawer fronts
>>> and I could proceed.
>>>
>>> These are inset drawers and that fact always adds a degree of difficulty
>>> over overlay drawer fronts.
>>>
>>> A couple of years ago I applied a bit of unused knowledge to make this
>>> process much easier.
>>>
>>> Shimming is a must but attaching the false fronts to the mounted drawers
>>> is always a bit tough. In fact there are special washer head screws for
>>> mounting drawer fronts through over sized holes to allow for
>>> readjustment after attaching. The typical procedure is to put screws
>>> into the front of the drawer from the inside and let the points of the
>>> screws stick out just a bit. Then press the outer false drawer front
>>> into the screw points, remove the front, locate the dimples made by the
>>> screw points, predrill shallow holes where there were indentations, line
>>> up the front with the screws, drive home the screws. And typically the
>>> drawer front is not perfectly placed.
>>>
>>> Now,,,,,,I wait until I have the pulls before I mount the false fronts.
>>> I drill the holes for the pulls into the false fronts only, place the
>>> false drawer front into position and place pocket hole screws through
>>> the false front drawer pull holes into the drawer, snugly. Those screws
>>> hold the false drawer front and allow you to open the drawer and add the
>>> remaining screws from the inside with out all of the steps listed above.
>>> Remove the pocket holes and finish drilling the holes for the pulls
>>> through the inner drawer.
>>>
>>> Anyway,,,
>>>
>>> The process with shims.
>>>
>>> https://www.flickr.com/photos/lcb11211/24664669262/in/dateposted-public/
>>>
>>> And the result, with no need for any adjustments and the pocket holes
>>> removed.
>>>
>>> https://www.flickr.com/photos/lcb11211/24756262116/in/dateposted-public/
>>>
>>>
>>>
>>
>> That's looking mighty good.
>>
>> I've been following yours and Karl's advice, been spending time in
>> Sketchup, which is why I've not been online but for short spurts.
>>
>> I'll be commenting on previous posts for the goodies I have learned
>> soon.
>>
>> Those drawers look almost tight enough that if high humidity hung
>> around long they'd swell up and become self locking drawers. ;)
>>
>
>If the cabinets were going to be in an uncontrolled environment I might be
>concerned about fit later on. But I too will be sealing with stain and
>varnish which will aid in stability.
>The drawer fronts have a 1/16" gap all of the way around.

Actually I meant that as a joke, seeing as they fit so very well.
Sorry for the confusion.

I had watched a video on making cabinet doors, and the door style he
was the proudest of was doors that fit like your drawer faces do. He
said it was a sign of a true craftsman.

On 2/5/2016 8:47 AM, Leon wrote:

> You should get him to show you a picture of his Canasta Card holder with
> Domino kick stand. ;~)

Too bad we can't get royalties on SketchUp Models.

Since I never look after occasionally uploading stuff to the 3D
Warehouse (always out of the altruistic goodness of my heart, doncha
know) I didn't even know you could get this info:

Just noticed my kitchen island model we installed in the straw bale
house in 2009 has been downloaded 3,748 times.

https://3dwarehouse.sketchup.com/model.html?id=60dc0155e1dffd87b2c2cd006d206129

And my Arts and Crafts Sofa table, I made for my living room, 3,210 times.

https://3dwarehouse.sketchup.com/model.html?id=bdc159bdb0147e2d54f10b531fe5914c

Jeeezzzusss ... where's my royalties, ferrcrssiskaes. LOL

--
eWoodShop: www.eWoodShop.com
Wood Shop: www.e-WoodShop.net
https://www.google.com/+eWoodShop
https://plus.google.com/+KarlCaillouet/posts
http://www.custommade.com/by/ewoodshop/
KarlCaillouet@ (the obvious)

On Thu, 4 Feb 2016 13:54:37 -0600, Leon <lcb11211@swbelldotnet> wrote:

>On 2/4/2016 1:32 PM, OFWW wrote:
>> On Wed, 3 Feb 2016 14:32:20 -0600, Leon <lcb11211@swbelldotnet> wrote:
>>
>>> On 2/3/2016 2:08 PM, OFWW wrote:
>>>> On Wed, 3 Feb 2016 07:50:42 -0600, Leon <[email protected]> wrote:
>>>>
>>>>> OFWW <[email protected]> wrote:
>>>>>> On Tue, 2 Feb 2016 18:40:38 -0600, Leon <lcb11211@swbelldotnet> wrote:
>>>>>>
>>>>>>> On 1/31/2016 3:44 PM, Leon wrote:
>>>>>>>
>>>>>>> So my customer got the pulls that she wanted to put on the drawer fronts
>>>>>>> and I could proceed.
>>>>>>>
>>>>>>> These are inset drawers and that fact always adds a degree of difficulty
>>>>>>> over overlay drawer fronts.
>>>>>>>
>>>>>>> A couple of years ago I applied a bit of unused knowledge to make this
>>>>>>> process much easier.
>>>>>>>
>>>>>>> Shimming is a must but attaching the false fronts to the mounted drawers
>>>>>>> is always a bit tough. In fact there are special washer head screws for
>>>>>>> mounting drawer fronts through over sized holes to allow for
>>>>>>> readjustment after attaching. The typical procedure is to put screws
>>>>>>> into the front of the drawer from the inside and let the points of the
>>>>>>> screws stick out just a bit. Then press the outer false drawer front
>>>>>>> into the screw points, remove the front, locate the dimples made by the
>>>>>>> screw points, predrill shallow holes where there were indentations, line
>>>>>>> up the front with the screws, drive home the screws. And typically the
>>>>>>> drawer front is not perfectly placed.
>>>>>>>
>>>>>>> Now,,,,,,I wait until I have the pulls before I mount the false fronts.
>>>>>>> I drill the holes for the pulls into the false fronts only, place the
>>>>>>> false drawer front into position and place pocket hole screws through
>>>>>>> the false front drawer pull holes into the drawer, snugly. Those screws
>>>>>>> hold the false drawer front and allow you to open the drawer and add the
>>>>>>> remaining screws from the inside with out all of the steps listed above.
>>>>>>> Remove the pocket holes and finish drilling the holes for the pulls
>>>>>>> through the inner drawer.
>>>>>>>
>>>>>>> Anyway,,,
>>>>>>>
>>>>>>> The process with shims.
>>>>>>>
>>>>>>> https://www.flickr.com/photos/lcb11211/24664669262/in/dateposted-public/
>>>>>>>
>>>>>>> And the result, with no need for any adjustments and the pocket holes
>>>>>>> removed.
>>>>>>>
>>>>>>> https://www.flickr.com/photos/lcb11211/24756262116/in/dateposted-public/
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>
>>>>>> That's looking mighty good.
>>>>>>
>>>>>> I've been following yours and Karl's advice, been spending time in
>>>>>> Sketchup, which is why I've not been online but for short spurts.
>>>>>>
>>>>>> I'll be commenting on previous posts for the goodies I have learned
>>>>>> soon.
>>>>>>
>>>>>> Those drawers look almost tight enough that if high humidity hung
>>>>>> around long they'd swell up and become self locking drawers. ;)
>>>>>>
>>>>>
>>>>> If the cabinets were going to be in an uncontrolled environment I might be
>>>>> concerned about fit later on. But I too will be sealing with stain and
>>>>> varnish which will aid in stability.
>>>>> The drawer fronts have a 1/16" gap all of the way around.
>>>>
>>>> Actually I meant that as a joke, seeing as they fit so very well.
>>>> Sorry for the confusion.
>>>
>>> Yeah, I saw the smiley face. ;~)
>>>
>>> I just wanted to explain a bit further my reasoning and spec's. ;~)
>>>
>>>>
>>>> I had watched a video on making cabinet doors, and the door style he
>>>> was the proudest of was doors that fit like your drawer faces do. He
>>>> said it was a sign of a true craftsman.
>>>>
>>>
>>> You do have to pay attention when using inset doors and drawers as
>>> opposed to overlay. Square is a must.
>>>
>>> Here are a couple of examples of inset doors and drawers.
>>>
>>> I built this Murphy bed and side towers 5 years ago for a customer..
>>>
>>> https://www.flickr.com/photos/lcb11211/5807616639/in/dateposted-public/
>>>
>>
>> You know, Murphy beds have really improved, and what a space saver.
>> Nothing can dual purpose a room like that, and most children's rooms
>> should be set up that way. I saw some a year or so ago, a couple even
>> a bunk bed arrangement. I've been considering putting one in a spare
>> bedroom.
>
>And I can point you towards the hardware supplier for that too. ;~)
>IIRC Rockler sells for that company too.
>

Yes, but they don't carry all the stuff available in Europe right now,
and they have a bunch of different products that can literally change
the function of a room in moments. I suppose that its because they are
short on RE in the big cities, so their spaces are small, like in
downtown NY where even 10x10 spaces are marketable.

In my minds eye I see that as a place ripe for the multipurpose
furnishing thus making life more pleasant for many people.

>
>
>>
>>> And Our bedroom 6 years ago... It is now in a newer home. I thought I
>>> would never have to move it. ;~(
>>>
>>> https://www.flickr.com/photos/lcb11211/4436685682/in/dateposted-public/
>>>
>>> The bed and tower have a total of 24 drawers. 18 under the bed.
>>>
>>
>> I didn't show my wife those pictures, got more than enough to do at
>> the moment. :)
>>
>> That must have kept you busy for quite a while.
>
>About 12 weeks.
>

Which in laymen's terms is more like 6 months at the minimum.

>>
>>> https://www.flickr.com/photos/lcb11211/4436686012/in/dateposted-public/
>>
>> Not to detract from the post, but in looking at your photo's I saw
>> this stunning piece of beauty!
>
>
>LOL, Thank you. Those were a labor of love, I built a pair for my
>sister and BIL. They had a walnut chest of drawers and a walnut dresser
>built by Waterford, IIRC. They wanted me to build night stands to
>match. That tested my talents. The tricky parts were the feet and the
>columns on the corners. I actually cut the columns "round" on the table
>saw. I spent an afternoon doing that.
>
>AND I wished I had Sketchup for the design, instead I was still using
>AutoCAD LT.
>
>
>>
>> https://www.flickr.com/photos/lcb11211/4332857960/in/dateposted-public/
>>
>> Is there a matching one to go with it?
>
>There were a pair.
>
>>
>> Something that looks like that needs to be openly displayed.
>>
>;~)

It had me drooling. :)

On 2/5/2016 1:08 AM, OFWW wrote:
> On Thu, 4 Feb 2016 14:08:55 -0600, Swingman <[email protected]> wrote:
>
>> On 2/4/2016 1:32 PM, OFWW wrote:
>>
>>> https://www.flickr.com/photos/lcb11211/4332857960/in/dateposted-public/
>>>
>>> Is there a matching one to go with it?
>>>
>>> Something that looks like that needs to be openly displayed.
>>
>> Good eye.
>>
>> I first saw that years ago and will never forget how stunning I also
>> thought it was. At the time using contrasting woods was just getting a
>> lot of attention on TV woodworking shows ... Leon out did them all.
>>
>> And, there is also a gorgeous, large jewelry box he made for Kim of
>> spalted wood, and a glass display case for a client, and a "Texas" desk
>> that are notable pieces of woodworking.
>>
>> Keep this up and his heads gonna swell bigger than ever ... :)
>
> Well,... Both of you men have a right and history to feel that at
> least once in a while. Neither of you rest on your laurels but seem to
> use that for your standard impelling you to do better. A good work
> ethic with creative skills goes far.
>

Yeah, Swingman has a home full of beautiful furniture too. There are
certain pieces that you simply cannot help but touch when ever you walk
by them. ;~) And he has a few Art and Crafts, or is that Green and
Green lamps that are friggin perfect!

You should get him to show you a picture of his Canasta Card holder with
Domino kick stand. ;~)

On 2/3/2016 2:08 PM, OFWW wrote:
> On Wed, 3 Feb 2016 07:50:42 -0600, Leon <[email protected]> wrote:
>
>> OFWW <[email protected]> wrote:
>>> On Tue, 2 Feb 2016 18:40:38 -0600, Leon <lcb11211@swbelldotnet> wrote:
>>>
>>>> On 1/31/2016 3:44 PM, Leon wrote:
>>>>
>>>> So my customer got the pulls that she wanted to put on the drawer fronts
>>>> and I could proceed.
>>>>
>>>> These are inset drawers and that fact always adds a degree of difficulty
>>>> over overlay drawer fronts.
>>>>
>>>> A couple of years ago I applied a bit of unused knowledge to make this
>>>> process much easier.
>>>>
>>>> Shimming is a must but attaching the false fronts to the mounted drawers
>>>> is always a bit tough. In fact there are special washer head screws for
>>>> mounting drawer fronts through over sized holes to allow for
>>>> readjustment after attaching. The typical procedure is to put screws
>>>> into the front of the drawer from the inside and let the points of the
>>>> screws stick out just a bit. Then press the outer false drawer front
>>>> into the screw points, remove the front, locate the dimples made by the
>>>> screw points, predrill shallow holes where there were indentations, line
>>>> up the front with the screws, drive home the screws. And typically the
>>>> drawer front is not perfectly placed.
>>>>
>>>> Now,,,,,,I wait until I have the pulls before I mount the false fronts.
>>>> I drill the holes for the pulls into the false fronts only, place the
>>>> false drawer front into position and place pocket hole screws through
>>>> the false front drawer pull holes into the drawer, snugly. Those screws
>>>> hold the false drawer front and allow you to open the drawer and add the
>>>> remaining screws from the inside with out all of the steps listed above.
>>>> Remove the pocket holes and finish drilling the holes for the pulls
>>>> through the inner drawer.
>>>>
>>>> Anyway,,,
>>>>
>>>> The process with shims.
>>>>
>>>> https://www.flickr.com/photos/lcb11211/24664669262/in/dateposted-public/
>>>>
>>>> And the result, with no need for any adjustments and the pocket holes
>>>> removed.
>>>>
>>>> https://www.flickr.com/photos/lcb11211/24756262116/in/dateposted-public/
>>>>
>>>>
>>>>
>>>
>>> That's looking mighty good.
>>>
>>> I've been following yours and Karl's advice, been spending time in
>>> Sketchup, which is why I've not been online but for short spurts.
>>>
>>> I'll be commenting on previous posts for the goodies I have learned
>>> soon.
>>>
>>> Those drawers look almost tight enough that if high humidity hung
>>> around long they'd swell up and become self locking drawers. ;)
>>>
>>
>> If the cabinets were going to be in an uncontrolled environment I might be
>> concerned about fit later on. But I too will be sealing with stain and
>> varnish which will aid in stability.
>> The drawer fronts have a 1/16" gap all of the way around.
>
> Actually I meant that as a joke, seeing as they fit so very well.
> Sorry for the confusion.

Yeah, I saw the smiley face. ;~)

I just wanted to explain a bit further my reasoning and spec's. ;~)

>
> I had watched a video on making cabinet doors, and the door style he
> was the proudest of was doors that fit like your drawer faces do. He
> said it was a sign of a true craftsman.
>

You do have to pay attention when using inset doors and drawers as
opposed to overlay. Square is a must.

Here are a couple of examples of inset doors and drawers.

I built this Murphy bed and side towers 5 years ago for a customer..

https://www.flickr.com/photos/lcb11211/5807616639/in/dateposted-public/

And Our bedroom 6 years ago... It is now in a newer home. I thought I
would never have to move it. ;~(

https://www.flickr.com/photos/lcb11211/4436685682/in/dateposted-public/

The bed and tower have a total of 24 drawers. 18 under the bed.

https://www.flickr.com/photos/lcb11211/4436686012/in/dateposted-public/

On 2/5/2016 8:47 AM, Leon wrote:

> You should get him to show you a picture of his Canasta Card holder with
> Domino kick stand. ;~)

That be museum quality woodworking, Bubba ... expensive to even view.

--
eWoodShop: www.eWoodShop.com
Wood Shop: www.e-WoodShop.net
https://www.google.com/+eWoodShop
https://plus.google.com/+KarlCaillouet/posts
http://www.custommade.com/by/ewoodshop/
KarlCaillouet@ (the obvious)

On 1/31/2016 10:11 PM, OFWW wrote:
> On Sun, 31 Jan 2016 15:44:22 -0600, Leon <lcb11211@swbelldotnet>
> wrote:
>
>> I finished the hard part of the drawers, building them.
>> I build them out of Baltic birch and used rabbeted corners reinforced
>> with Domino floating tenons. I have built a few hundred drawers this
>> way and it seems I am still learning how to stream line this process.
>>
>> The pieces,
>>
>> https://www.flickr.com/photos/lcb11211/24382723850/in/dateposted-public/
>>
>> Glued up,
>>
>> https://www.flickr.com/photos/lcb11211/24050071344/in/dateposted-public/
>>
>> Domino floating tenons installed and the drawers mounted in the cabinets.
>>
>
> Are those installed after the drawers are glued up?

Yes


>
>> https://www.flickr.com/photos/lcb11211/24370070979/in/dateposted-public/
>>
>> And the solid drawer fronts ready for stain. I cut the bevels on the TS
>> and then sanded.
>>
>> https://www.flickr.com/photos/lcb11211/24109563244/in/dateposted-public/
>
> Very nice!
>

Thank you.

On 1/31/2016 6:16 PM, Swingman wrote:
> On 1/31/2016 3:44 PM, Leon wrote:
>> I finished the hard part of the drawers, building them.
>> I build them out of Baltic birch and used rabbeted corners reinforced
>> with Domino floating tenons. I have built a few hundred drawers this
>> way and it seems I am still learning how to stream line this process.
>
>
> Ah yes, the infamous "Domino Drawers" ... looking good, as usual.
>


Thank you, partner. ;~0