I understand that if you promote the wands as "Harry Potter" wands, you
will be in trouble, I read a posting of a guy who had his listing
kicked off eBay for this. If you promote them as "magic wands" you will
be OK.
There is a group on Yahoo called "wandcrafters". Not very active, but
they have some images and info on making wands.
Brad Harding
HardingPens.com
Owen Lawrence wrote:
>
> Actually, that's exactly what I was trying to do. I got it down to about a
> minimum of 3/8" thick by 1' or less, but after that I get a lot of catches.
> I'm not willing to blame my lathe entirely, but it vibrates a lot. My tools
> are as sharp as I can make them. I think I'll ask if I can try it on a
> friend's lathe to see if it makes any difference. It got to the point where
> I gave up pending building a steady. I don't know if I could make a
> trapping plane that would work any good, but that's a new idea to me (thanks
> Andy).
>
> - Owen -
It's a lot easier if you use a chuck like the SuperNova2 or
Talon type. Cut your stock square, chuck up the handle
piece and drill a hole in the end for the tenon you'll turn
on the end of the wand part later.
By using a chuck to hold the drive end and a live center on the
tail stock you can greatly reduce one source of the problem -
the springing you get when using a spur or stebb center on
the drive side. Compressing the blank between the head
stock spur drive and the live center will
If you start rounding from the tails stock end and work your
way back to the chuck - cutting towards the tail stock also
helps because you're automatically tapering, k with lots of
beef to the left for rigidity. Cut the tenon on the wand part
last as it will be closest to the chuck where things are
the most stabile.
If you set the tool rest lower than normal and use a 1/2"
or 3/4" roughing gouge, handle pretty low and do light
passes, you'll reduce the likelyhood of a catch. Higher RPMs
also helps.
And don't forget about the "80 grit gouge" I've NEVER had
a catch using my trusty "80".
Sand to 320 before cutting in details.
Handle details with a half inch skew - at low RPMS, detail
gouge at higher RPMs
(Here's some ideas for wands
http://home.comcast.net/~charliebcz/MagicWands/MagicWands.html
http://home.comcast.net/~charliebcz/Turning/Turning2.html
and then try doing some hair sticks
http://home.comcast.net/~charliebcz/Turning/Turning12.html
charlie b
On Wed, 14 Dec 2005 10:21:06 GMT, Lobby Dosser
<[email protected]> wrote:
>"Buddy Matlosz" <[email protected]> wrote:
>
>> Newspaper story of a NJ guy who turns Harry Potter-type magic wands:
>>
>> http://www.app.com/apps/pbcs.dll/article?AID=/20051212/NEWS/512120328&S
>> earchID=73229370875998
>>
>>
>>
>
>But, do they Glow In The Dark?
LOL!
--
Chuck *#:^)
chaz3913(AT)yahoo(DOT)com
Anti-spam sig: please remove "NO SPAM" from e-mail address to reply.
<><
September 11, 2001 - Never Forget
----== Posted via Newsfeeds.Com - Unlimited-Unrestricted-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----
"BillR" <[email protected]> wrote in message
news:[email protected]...
>I made one but it wouldn't work. Do I need a unicorn or will the ashes from
> a phoenix work?
>
> "Andy Dingley" <[email protected]> wrote in message
> news:[email protected]...
>> I'm now finding it _very_ easy to turn these long thin tapers.
>> I made a "trapping plane"
>
>
It _is_ a dowel, after all.
http://web.onetel.com/~ashemcrafts/products_trapping_plane.htm
Or drive it through a plate, lay in tapered V-block and scrape the taper.
"Buddy Matlosz" <[email protected]> wrote in message
news:[email protected]...
> Newspaper story of a NJ guy who turns Harry Potter-type magic wands:
>
> http://www.app.com/apps/pbcs.dll/article?AID=/20051212/NEWS/512120328&SearchID=73229370875998
I've tried to do this. It's not as easy as it looks. I'll keep trying.
- Owen -
Geez, I've been making them for the neighborhood kids since shortly after
the first book came out.
Nothing hard about it. Getting 60+ bucks for them is impressive though.
Guess it just goes to show that marketing is whats its all about......
--JD
"Buddy Matlosz" <[email protected]> wrote in message
news:[email protected]...
> Newspaper story of a NJ guy who turns Harry Potter-type magic wands:
>
> http://www.app.com/apps/pbcs.dll/article?AID=/20051212/NEWS/512120328&SearchID=73229370875998
>
>
Owen, I don't know how you do it but it's a little easier if you make
the handle one part and then make the pointy stick end another part,
rather than trying to make the whole thing a one piece turning.
Also using different woods for some nice color combination and/or contrast.
Have fun and take care
Leo Van Der Loo
Owen Lawrence wrote:
> I've tried to do this. It's not as easy as it looks. I'll keep trying.
>
> - Owen -
>
>
Juergen Hannappel wrote:
> "Buddy Matlosz" <[email protected]> writes:
>
>> Newspaper story of a NJ guy who turns Harry Potter-type magic wands:
>>
>>
http://www.app.com/apps/pbcs.dll/article?AID=/20051212/NEWS/512120328&SearchID=73229370875998
>
> Sounds like a terrilby risky business: What if Lord Vol^H^H^H^H the
> lawyers of the marchadise company find out and come for their 1000%
> share of the profits?
He's not claiming any relationship to the movie on his site, and magic wands
were certainly readily available in commerce before the Harry Potter movies
so it seems unlikely that they would have a chance of collecting anything.
Besides, he's small potatoes in the wand business.
--
--John
to email, dial "usenet" and validate
(was jclarke at eye bee em dot net)
I made one but it wouldn't work. Do I need a unicorn or will the ashes from
a phoenix work?
"Andy Dingley" <[email protected]> wrote in message
news:[email protected]...
> On Tue, 13 Dec 2005 23:30:57 -0500, "Owen Lawrence"
> <[email protected]> wrote:
>
> >I've tried to do this. It's not as easy as it looks. I'll keep trying.
>
> I'm now finding it _very_ easy to turn these long thin tapers.
> I made a "trapping plane"
"Leo Van Der Loo" <[email protected]> wrote in message
news:[email protected]...
> Owen, I don't know how you do it but it's a little easier if you make the
> handle one part and then make the pointy stick end another part, rather
> than trying to make the whole thing a one piece turning.
> Also using different woods for some nice color combination and/or
> contrast.
>
Actually, that's exactly what I was trying to do. I got it down to about a
minimum of 3/8" thick by 1' or less, but after that I get a lot of catches.
I'm not willing to blame my lathe entirely, but it vibrates a lot. My tools
are as sharp as I can make them. I think I'll ask if I can try it on a
friend's lathe to see if it makes any difference. It got to the point where
I gave up pending building a steady. I don't know if I could make a
trapping plane that would work any good, but that's a new idea to me (thanks
Andy).
- Owen -
"Buddy Matlosz" <[email protected]> wrote:
> Newspaper story of a NJ guy who turns Harry Potter-type magic wands:
>
> http://www.app.com/apps/pbcs.dll/article?AID=/20051212/NEWS/512120328&S
> earchID=73229370875998
>
>
>
But, do they Glow In The Dark?
George,
Not sure I understand the "plate and V-block" arrangement. Any pictures of
just how this is done?
And any comments on turning cue sticks?
Thanks
TomNie
"George" <George@least> wrote in message
news:[email protected]...
>
> "BillR" <[email protected]> wrote in message
> news:[email protected]...
>>I made one but it wouldn't work. Do I need a unicorn or will the ashes
>>from
>> a phoenix work?
>>
>> "Andy Dingley" <[email protected]> wrote in message
>> news:[email protected]...
>
>>> I'm now finding it _very_ easy to turn these long thin tapers.
>>> I made a "trapping plane"
>>
>>
>
> It _is_ a dowel, after all.
> http://web.onetel.com/~ashemcrafts/products_trapping_plane.htm
> Or drive it through a plate, lay in tapered V-block and scrape the taper.
>
On Tue, 13 Dec 2005 23:30:57 -0500, "Owen Lawrence"
<[email protected]> wrote:
>I've tried to do this. It's not as easy as it looks. I'll keep trying.
I'm now finding it _very_ easy to turn these long thin tapers.
I made a "trapping plane"
On Wed, 14 Dec 2005 22:38:18 -0000, "BillR" <[email protected]> wrote:
>I made one but it wouldn't work. Do I need a unicorn or will the ashes from
>a phoenix work?
>
Oh man, "a phoenix", I thought it said "ashes from Phoenix". No wonder
mine didn't work.
>"Andy Dingley" <[email protected]> wrote in message
>news:[email protected]...
>> On Tue, 13 Dec 2005 23:30:57 -0500, "Owen Lawrence"
>> <[email protected]> wrote:
>>
>> >I've tried to do this. It's not as easy as it looks. I'll keep trying.
>>
>> I'm now finding it _very_ easy to turn these long thin tapers.
>> I made a "trapping plane"
>
+--------------------------------------------------------------------------------+
If you're gonna be dumb, you better be tough
+--------------------------------------------------------------------------------+
"Buddy Matlosz" <[email protected]> writes:
> Newspaper story of a NJ guy who turns Harry Potter-type magic wands:
>
> http://www.app.com/apps/pbcs.dll/article?AID=/20051212/NEWS/512120328&SearchID=73229370875998
Sounds like a terrilby risky business: What if Lord Vol^H^H^H^H the
lawyers of the marchadise company find out and come for their 1000%
share of the profits?
--
Dr. Juergen Hannappel http://lisa2.physik.uni-bonn.de/~hannappe
mailto:[email protected] Phone: +49 228 73 2447 FAX ... 7869
Physikalisches Institut der Uni Bonn Nussallee 12, D-53115 Bonn, Germany
CERN: Phone: +412276 76461 Fax: ..77930 Bat. 892-R-A13 CH-1211 Geneve 23