I've narrowed my saw choices down to these two. Both have cast iron
wings and a decent (not great) fence. From what I've read, the Jet is
one of the best "contractor's saws" out there, and lots of folks
really like it. The Craftsman is a new model, and built more like a
cabinet saw (nice!) but still has a "small" motor like a contractor's
saw.
My shop is currently in about 1/4 of a good sized two car garage.
Over time I might be able to extend that to 1/2, but I cannot have the
whole thing... I'm a hobbyist and will use the saw for small/medium
furniture & cabinets, jewelry boxes, and the like... I'm currently
using one of those "total crap" $100 Delta tabletop saws and although
I've actually built some OK stuff with it, I finally figured out (what
took me so long!) that its just not accurate enough for real work.
I can get the Jet locally for about $700 to $750 and I'm sure I'd be
"satisfied". However, the Craftsman is actually roughly the same
price (or even slightly less, depending on sales) and I'm tempted
because of all the good stuff I read about cabinet style saws with the
trunnions mounted to the cabinet.
FYI: I have 120 in my shop, and the panel is down there so I can run
220 if needed, but that's extra $$. I've considered the Grizzly
1023S, but the others listed still seem like better choices to me...
SO: between these two saws in the title, which one would you
recommend, and why?
Hi, I was considering a General Contractor type saw, the wait was going to
be no telling how long. So, I decided to go with a Griz 1023s cab. saw.
The saw has a 3 hp motow, plenty of power. The set-up was effortless, love
it. You really should consider it.
Tony
"Bryan Dawson" <[email protected]> wrote in message
news:[email protected]...
> I've narrowed my saw choices down to these two. Both have cast iron
> wings and a decent (not great) fence. From what I've read, the Jet is
> one of the best "contractor's saws" out there, and lots of folks
> really like it. The Craftsman is a new model, and built more like a
> cabinet saw (nice!) but still has a "small" motor like a contractor's
> saw.
>
> My shop is currently in about 1/4 of a good sized two car garage.
> Over time I might be able to extend that to 1/2, but I cannot have the
> whole thing... I'm a hobbyist and will use the saw for small/medium
> furniture & cabinets, jewelry boxes, and the like... I'm currently
> using one of those "total crap" $100 Delta tabletop saws and although
> I've actually built some OK stuff with it, I finally figured out (what
> took me so long!) that its just not accurate enough for real work.
>
> I can get the Jet locally for about $700 to $750 and I'm sure I'd be
> "satisfied". However, the Craftsman is actually roughly the same
> price (or even slightly less, depending on sales) and I'm tempted
> because of all the good stuff I read about cabinet style saws with the
> trunnions mounted to the cabinet.
>
> FYI: I have 120 in my shop, and the panel is down there so I can run
> 220 if needed, but that's extra $$. I've considered the Grizzly
> 1023S, but the others listed still seem like better choices to me...
>
> SO: between these two saws in the title, which one would you
> recommend, and why?
On Mon, 15 Nov 2004 15:15:53 -0800, Bryan Dawson wrote:
> My shop is currently in about 1/4 of a good sized two car garage. Over
> time I might be able to extend that to 1/2, but I cannot have the whole
> thing... I'm a hobbyist and will use the saw for small/medium furniture &
> cabinets, jewelry boxes, and the like...
Sounds like exactly the size shop I have (a smallish room in the basement)
and the same sort of work.
> I can get the Jet locally for about $700 to $750 and I'm sure I'd be
> "satisfied". However, the Craftsman is actually roughly the same price
> (or even slightly less, depending on sales) and I'm tempted because of all
> the good stuff I read about cabinet style saws with the trunnions mounted
> to the cabinet.
I have the mid-range Craftsman, and was very happy for the cabinet-style
construction tonight when I had to align the table to the blade. Loosen
four bolts, a few well-placed whacks with a rubber mallet and done (well,
helps to tighten the table bolts back up too). I suspect that might have
been more of a production with table-mounted trunnions. I've never liked
the standard contractor-style design with the motor sticking out the back,
either. The Craftsman has a built-in dust collection port, but since I
don't have a DC and never remember to hook up the shop vac to it, I just
periodically open the side panel and vacuum out the cabinet.
--
-Chip Olson. | ceo2 at thsi dot org | remove the 2 to reply