"Gramps' shop" <[email protected]> wrote in
news:[email protected]:
> Got it ... and I am embarrassed beyond measure to report I was
> tightening it instead of loosening it. I misread the docs on the
> direction to turn. That's what I get for trying to read something
> upside down (the docs, not me).
>
I've been advised to tighten a stuck nut to try to break it free.
Sometimes that reveals the nut turns the other way.
Puckdropper
--
Make it to fit, don't make it fit.
Got it ... and I am embarrassed beyond measure to report I was tightening it instead of loosening it. I misread the docs on the direction to turn. That's what I get for trying to read something upside down (the docs, not me).
On Thursday, May 1, 2014 2:04:32 PM UTC-5, woodchucker wrote:
> On 5/1/2014 2:28 PM, Gramps' shop wrote:
>
> > Hey Domino guys ...
>
> >
>
> > I need to swap cutters and the one currently installed won't budge. Before I start hitting it with WD-40, I wonder if any of you have some better ideas.
>
> >
>
> > Larry
>
> >
>
>
>
> Maybe take a wooden clamp (hand screw or regular clamp with wooden
>
> blocks) tighten it on the bit and pull it off twist if necessary. Try
>
> twisting it in the direction it spins... thinking it picked up a burr
>
> and its against the turn direction, with it might free it up.
>
>
>
>
>
>
>
> --
>
> Jeff
On 5/1/2014 2:12 PM, Gramps' shop wrote:
> Got it ... and I am embarrassed beyond measure to report I was tightening it instead of loosening it. I misread the docs on the direction to turn. That's what I get for trying to read something upside down (the docs, not me).
>
>
> On Thursday, May 1, 2014 2:04:32 PM UTC-5, woodchucker wrote:
>> On 5/1/2014 2:28 PM, Gramps' shop wrote:
>>
>>> Hey Domino guys ...
>>
>>>
>>
>>> I need to swap cutters and the one currently installed won't budge. Before I start hitting it with WD-40, I wonder if any of you have some better ideas.
>>
>>>
>>
>>> Larry
>>
>>>
>>
>>
>>
>> Maybe take a wooden clamp (hand screw or regular clamp with wooden
>>
>> blocks) tighten it on the bit and pull it off twist if necessary. Try
>>
>> twisting it in the direction it spins... thinking it picked up a burr
>>
>> and its against the turn direction, with it might free it up.
Remember that a nut/blade/cutter always loosens in the same direction
that it normally spins.
On 5/1/2014 3:12 PM, Gramps' shop wrote:
> Got it ... and I am embarrassed beyond measure to report I was tightening it instead of loosening it. I misread the docs on the direction to turn. That's what I get for trying to read something upside down (the docs, not me).
>
>
Damn, I had the acetylene torch out ready to help. Have anything else
that needs to be loosened?
On 5/1/2014 1:28 PM, Gramps' shop wrote:
> Hey Domino guys ...
>
> I need to swap cutters and the one currently installed won't budge. Before I start hitting it with WD-40, I wonder if any of you have some better ideas.
>
> Larry
>
Yes, support the turret so that you do not force it to move in the
direction that it normally moves. Festool advised me many years ago to
preferably apply force either up or down. Apparently you can knock the
left and right calibration out of whack if you force in those,
left/right, directions. And support the turret on a bench top with the
bit hanging our over the edge.
Other than that a penetrating lube should work, I do find that the bit
does get tight so anything past a little snug when reinstalled is too much.
I wonder if a bit of Teflon tape or grease might alleviate the problem.
On 5/2/2014 11:01 AM, Morgans wrote:
> Impact wrench or tap a wrench with a hammer.
NO. Way too radical for this particular situation. Likely to do more
harm than good.
>
> "Puckdropper" <puckdropper(at)yahoo(dot)com> wrote in message
> news:[email protected]...
>> "Gramps' shop" <[email protected]> wrote in
>> news:[email protected]:
>>
>>> Got it ... and I am embarrassed beyond measure to report I was
>>> tightening it instead of loosening it. I misread the docs on the
>>> direction to turn. That's what I get for trying to read something
>>> upside down (the docs, not me).
>>>
>>
>> I've been advised to tighten a stuck nut to try to break it free.
>> Sometimes that reveals the nut turns the other way.
>>
>> Puckdropper
>> --
>> Make it to fit, don't make it fit.
>
>
> ---
> This email is free from viruses and malware because avast! Antivirus
> protection is active.
> http://www.avast.com
>
Impact wrench or tap a wrench with a hammer.
"Puckdropper" <puckdropper(at)yahoo(dot)com> wrote in message
news:[email protected]...
> "Gramps' shop" <[email protected]> wrote in
> news:[email protected]:
>
>> Got it ... and I am embarrassed beyond measure to report I was
>> tightening it instead of loosening it. I misread the docs on the
>> direction to turn. That's what I get for trying to read something
>> upside down (the docs, not me).
>>
>
> I've been advised to tighten a stuck nut to try to break it free.
> Sometimes that reveals the nut turns the other way.
>
> Puckdropper
> --
> Make it to fit, don't make it fit.
---
This email is free from viruses and malware because avast! Antivirus protection is active.
http://www.avast.com
On 5/1/2014 2:28 PM, Gramps' shop wrote:
> Hey Domino guys ...
>
> I need to swap cutters and the one currently installed won't budge. Before I start hitting it with WD-40, I wonder if any of you have some better ideas.
>
> Larry
>
Maybe take a wooden clamp (hand screw or regular clamp with wooden
blocks) tighten it on the bit and pull it off twist if necessary. Try
twisting it in the direction it spins... thinking it picked up a burr
and its against the turn direction, with it might free it up.
--
Jeff
On 5/1/2014 2:12 PM, Gramps' shop wrote:
> Got it ... and I am embarrassed beyond measure to report I was tightening it instead of loosening it. I misread the docs on the direction to turn. That's what I get for trying to read something upside down (the docs, not me).
Nah, you were just looking at it from the wrong side. ;)
--
eWoodShop: www.eWoodShop.com
Wood Shop: www.e-WoodShop.net
https://www.google.com/+eWoodShop
https://plus.google.com/+KarlCaillouet/posts
http://www.custommade.com/by/ewoodshop/
KarlCaillouet@ (the obvious)