Recently I finished working on 3 similar jewelry boxes. It's a design
I have done before with a dovetailed box in the middle suspended
between two vertical natural edge slabs. Rails across the top and
bottom of the box are pocket-screwed into the slabs, and the pocket
holes covered with some decorative pieces. The box houses a number of
drawers, which may also have some natural edged drawer fronts, so the
drawers are odd heights. The drawer slides are dadoed into the sides
of the box, only glued at the front to allow for expansion /
contraction.
After completing all of them, with the caps glued over the pocket
holes and finishing complete it was with much chagrin that I noticed
that the orientation arrow inside the box which ought to be pointing
up was in fact pointing down. Oh well, flip it over, right? Except
the slabs on this one were quite nice at the 'top' ends and not very
nice at all at the 'bottom', with one of them tapering significantly
so that the back rail was only partially flush to it.
However, on only this one out of the three the drawers were
symmetrical. So theoretically I could put the drawers in with it
upside-down. But there was no way that the slides were going to line
up like that. But what is the harm in trying, right?
They fit almost perfectly.
All I had to do was lower two of them on one side by 1/32" or so. And
I was able to just barely fit my LV miniature shoulder plane in
between the slides. So it took all of 2 minutes to fix what would
have been the biggest mistake I've made all year.
If you are anything like me, at this point you would now be wondering
when the other shoe was going to drop, because that just doesn't
happen without something else happening to make up for it. And I
didn't have to wait long.
The next thing to do was to drill the holes in one of the other ones
for the knobs. Take a drawer out, mark the center, drill the hole,
put it back. That's a pretty simple task, eh? One that would really
cause a problem if you screwed it up, eh? Yeah. On the 4th one I
went from marking at whatever dimension minus an 1/8th to plus an
1/8th.
So I got to sand all those drawer fronts down, make wooden pulls and
glue them on, and refinish them. And all is right with the universe
again.
Anyway, here are the three of them:
http://www.etsy.com/listing/62798076/spirit-of-the-woods-ii-jewelry-box
http://www.etsy.com/listing/62941009/spirit-of-the-woods-iii-jewelry-box
http://www.etsy.com/listing/63544321/spirit-of-the-woods-iv-jewelry-box
-Kevin
PS that mini shoulder plane has caused me more pain, it's so darn
small I keep smacking my hand into stuff, so it's about time its size
came in handy. Still I wish they made one just like it the same width
but double the rest. I have the bigger rabbet plane but this one is
much easier to adjust.
On Sat, 4 Dec 2010 13:59:50 -0800 (PST), Robatoy
<[email protected]> wrote:
>It has always been exciting for me to see 'rough-and-tumble' elegance.
>Very hard to categorize (probably impossible anyway) it is an form of
>art that I have seen and heard in many disciplines. Stevie Ray Vaughn
>is, in terms of technical ability, as rough and crude as it gets. But
>he creates warmth with spikes and barbs. A true artist. Early
>Picasso... same deal. In a documentary I saw once, he took a simple
>brush with black ink and slobbered some shapes and before my very
>eyes, they became alive.
>
>Your stuff talks to me that way. Beautiful, just absolutely
>gorgeous..... This stuff should be in a gallery somewhere.. like 5th
>Ave NYC
Aww shucks... I was just going for fairly simple to make but with
enough wow factor to get a decent margin, but I will settle for art.
Hey can I quote you on that for the website? :)
>Refined like a Keith Moon drum solo.
Now you have me wondering what would have happened if Keith Moon had
gotten into shop class instead of music. Blow up tree with dynamite,
start putting it back together until it looks like a table?
-Kevin
"Kevin" <[email protected]> wrote in message
news:[email protected]...
> Recently I finished working on 3 similar jewelry boxes. It's a design
> I have done before with a dovetailed box in the middle suspended
> between two vertical natural edge slabs. Rails across the top and
> bottom of the box are pocket-screwed into the slabs, and the pocket
> holes covered with some decorative pieces. The box houses a number of
> drawers, which may also have some natural edged drawer fronts, so the
> drawers are odd heights. The drawer slides are dadoed into the sides
> of the box, only glued at the front to allow for expansion /
> contraction.
>
> After completing all of them, with the caps glued over the pocket
> holes and finishing complete it was with much chagrin that I noticed
> that the orientation arrow inside the box which ought to be pointing
> up was in fact pointing down. Oh well, flip it over, right? Except
> the slabs on this one were quite nice at the 'top' ends and not very
> nice at all at the 'bottom', with one of them tapering significantly
> so that the back rail was only partially flush to it.
>
> However, on only this one out of the three the drawers were
> symmetrical. So theoretically I could put the drawers in with it
> upside-down. But there was no way that the slides were going to line
> up like that. But what is the harm in trying, right?
>
> They fit almost perfectly.
>
> All I had to do was lower two of them on one side by 1/32" or so. And
> I was able to just barely fit my LV miniature shoulder plane in
> between the slides. So it took all of 2 minutes to fix what would
> have been the biggest mistake I've made all year.
>
> If you are anything like me, at this point you would now be wondering
> when the other shoe was going to drop, because that just doesn't
> happen without something else happening to make up for it. And I
> didn't have to wait long.
>
> The next thing to do was to drill the holes in one of the other ones
> for the knobs. Take a drawer out, mark the center, drill the hole,
> put it back. That's a pretty simple task, eh? One that would really
> cause a problem if you screwed it up, eh? Yeah. On the 4th one I
> went from marking at whatever dimension minus an 1/8th to plus an
> 1/8th.
>
> So I got to sand all those drawer fronts down, make wooden pulls and
> glue them on, and refinish them. And all is right with the universe
> again.
>
> Anyway, here are the three of them:
>
> http://www.etsy.com/listing/62798076/spirit-of-the-woods-ii-jewelry-box
> http://www.etsy.com/listing/62941009/spirit-of-the-woods-iii-jewelry-box
> http://www.etsy.com/listing/63544321/spirit-of-the-woods-iv-jewelry-box
>
>
> -Kevin
>
> PS that mini shoulder plane has caused me more pain, it's so darn
> small I keep smacking my hand into stuff, so it's about time its size
> came in handy. Still I wish they made one just like it the same width
> but double the rest. I have the bigger rabbet plane but this one is
> much easier to adjust.
Beautiful!
"Kevin" <[email protected]> wrote
>
> Anyway, here are the three of them:
>
> http://www.etsy.com/listing/62798076/spirit-of-the-woods-ii-jewelry-box
> http://www.etsy.com/listing/62941009/spirit-of-the-woods-iii-jewelry-box
> http://www.etsy.com/listing/63544321/spirit-of-the-woods-iv-jewelry-box
>
>
Beautiful work there Kevin.
I don't wish to alarm you but somebody sold you some wood that still had
bark on it. And there appears to be some kind of rot or insect infestation
in the middle of two of the boxes. Just though you should know.
<grin, duck and run>
Kevin wrote:
>
> So I got to sand all those drawer fronts down, make wooden pulls and
> glue them on, and refinish them. And all is right with the universe
> again.
>
> Anyway, here are the three of them:
>
> http://www.etsy.com/listing/62798076/spirit-of-the-woods-ii-jewelry-box
> http://www.etsy.com/listing/62941009/spirit-of-the-woods-iii-jewelry-box
> http://www.etsy.com/listing/63544321/spirit-of-the-woods-iv-jewelry-box
>
Beautifully done Kevin!
--
Jack Novak
Buffalo, NY - USA
[email protected]
On Dec 4, 5:14=A0pm, FrozenNorth <[email protected]>
wrote:
> On 12/03/10 11:16 PM, Kevin wrote:
>
>
>
> > Recently I finished working on 3 similar jewelry boxes. =A0It's a desig=
n
> > I have done before with a dovetailed box in the middle suspended
> > between two vertical natural edge slabs. =A0Rails across the top and
> > bottom of the box are pocket-screwed into the slabs, and the pocket
> > holes covered with some decorative pieces. =A0The box houses a number o=
f
> > drawers, which may also have some natural edged drawer fronts, so the
> > drawers are odd heights. =A0The drawer slides are dadoed into the sides
> > of the box, only glued at the front to allow for expansion /
> > contraction.
>
> > After completing all of them, with the caps glued over the pocket
> > holes and finishing complete it was with much chagrin that I noticed
> > that the orientation arrow inside the box which ought to be pointing
> > up was in fact pointing down. =A0Oh well, flip it over, right? =A0Excep=
t
> > the slabs on this one were quite nice at the 'top' ends and not very
> > nice at all at the 'bottom', with one of them tapering significantly
> > so that the back rail was only partially flush to it.
>
> > However, on only this one out of the three the drawers were
> > symmetrical. =A0So theoretically I could put the drawers in with it
> > upside-down. =A0But there was no way that the slides were going to line
> > up like that. =A0But what is the harm in trying, right?
>
> > They fit almost perfectly.
>
> > All I had to do was lower two of them on one side by 1/32" or so. =A0An=
d
> > I was able to just barely fit my LV miniature shoulder plane in
> > between the slides. =A0So it took all of 2 minutes to fix what would
> > have been the biggest mistake I've made all year.
>
> > If you are anything like me, at this point you would now be wondering
> > when the other shoe was going to drop, because that just doesn't
> > happen without something else happening to make up for it. =A0And I
> > didn't have to wait long.
>
> > The next thing to do was to drill the holes in one of the other ones
> > for the knobs. =A0Take a drawer out, mark the center, drill the hole,
> > put it back. =A0That's a pretty simple task, eh? =A0One that would real=
ly
> > cause a problem if you screwed it up, eh? =A0Yeah. =A0On the 4th one I
> > went from marking at whatever dimension minus an 1/8th to plus an
> > 1/8th.
>
> > So I got to sand all those drawer fronts down, make wooden pulls and
> > glue them on, and refinish them. =A0And all is right with the universe
> > again.
>
> > Anyway, here are the three of them:
>
> >http://www.etsy.com/listing/62798076/spirit-of-the-woods-ii-jewelry-box
> >http://www.etsy.com/listing/62941009/spirit-of-the-woods-iii-jewelry-box
> >http://www.etsy.com/listing/63544321/spirit-of-the-woods-iv-jewelry-box
>
> I have one word for you, fucking WOW, that is gorgeous.
>
> --
> Froz...
>
> The system will be down for 10 days for preventive maintenance.
"Fucking WOW" works for me too...<G>
Scraping lowers the chatoyance a bit. I am looking for this to really
pop, I want the best use of this wood. It looks so amazing even with the
scar of the pith.
BTW did you ever notice the most beatiful pieces of wood are all
technically or near defects.
Burls,
Birds Eye Maple
Quilted stock...
etc...
On 12/6/2010 8:16 AM, Ecnerwal wrote:
> In article<[email protected]>,
> tiredofspam<nospam.nospam.com> wrote:
>
>> I'm actually doing a night table for my wife and it has similar grain
>> and pith.. My problem has been planing by hand. It's been tough the
>> grain has not been very friendly to work on. I want the chatoyance, so I
>> don't want to sand it.
>
> Scraping is the way to take on grain that does not want to plane.
>
In article <[email protected]>,
tiredofspam <nospam.nospam.com> wrote:
> I'm actually doing a night table for my wife and it has similar grain
> and pith.. My problem has been planing by hand. It's been tough the
> grain has not been very friendly to work on. I want the chatoyance, so I
> don't want to sand it.
Scraping is the way to take on grain that does not want to plane.
--
Cats, coffee, chocolate...vices to live by
On Dec 4, 2:22=A0pm, Robatoy <[email protected]> wrote:
> On Dec 4, 5:14=A0pm, FrozenNorth <[email protected]>
> wrote:
>
>
>
>
>
> > On 12/03/10 11:16 PM, Kevin wrote:
>
> > > Recently I finished working on 3 similar jewelry boxes. =A0It's a des=
ign
> > > I have done before with a dovetailed box in the middle suspended
> > > between two vertical natural edge slabs. =A0Rails across the top and
> > > bottom of the box are pocket-screwed into the slabs, and the pocket
> > > holes covered with some decorative pieces. =A0The box houses a number=
of
> > > drawers, which may also have some natural edged drawer fronts, so the
> > > drawers are odd heights. =A0The drawer slides are dadoed into the sid=
es
> > > of the box, only glued at the front to allow for expansion /
> > > contraction.
>
> > > After completing all of them, with the caps glued over the pocket
> > > holes and finishing complete it was with much chagrin that I noticed
> > > that the orientation arrow inside the box which ought to be pointing
> > > up was in fact pointing down. =A0Oh well, flip it over, right? =A0Exc=
ept
> > > the slabs on this one were quite nice at the 'top' ends and not very
> > > nice at all at the 'bottom', with one of them tapering significantly
> > > so that the back rail was only partially flush to it.
>
> > > However, on only this one out of the three the drawers were
> > > symmetrical. =A0So theoretically I could put the drawers in with it
> > > upside-down. =A0But there was no way that the slides were going to li=
ne
> > > up like that. =A0But what is the harm in trying, right?
>
> > > They fit almost perfectly.
>
> > > All I had to do was lower two of them on one side by 1/32" or so. =A0=
And
> > > I was able to just barely fit my LV miniature shoulder plane in
> > > between the slides. =A0So it took all of 2 minutes to fix what would
> > > have been the biggest mistake I've made all year.
>
> > > If you are anything like me, at this point you would now be wondering
> > > when the other shoe was going to drop, because that just doesn't
> > > happen without something else happening to make up for it. =A0And I
> > > didn't have to wait long.
>
> > > The next thing to do was to drill the holes in one of the other ones
> > > for the knobs. =A0Take a drawer out, mark the center, drill the hole,
> > > put it back. =A0That's a pretty simple task, eh? =A0One that would re=
ally
> > > cause a problem if you screwed it up, eh? =A0Yeah. =A0On the 4th one =
I
> > > went from marking at whatever dimension minus an 1/8th to plus an
> > > 1/8th.
>
> > > So I got to sand all those drawer fronts down, make wooden pulls and
> > > glue them on, and refinish them. =A0And all is right with the univers=
e
> > > again.
>
> > > Anyway, here are the three of them:
>
> > >http://www.etsy.com/listing/62798076/spirit-of-the-woods-ii-jewelry-bo=
x
> > >http://www.etsy.com/listing/62941009/spirit-of-the-woods-iii-jewelry-b=
ox
> > >http://www.etsy.com/listing/63544321/spirit-of-the-woods-iv-jewelry-bo=
x
>
> > I have one word for you, fucking WOW, that is gorgeous.
>
> > --
> > Froz...
>
> > The system will be down for 10 days for preventive maintenance.
>
> "Fucking WOW" works for me too...<G>
Me three
Luigi
On Dec 3, 11:16=A0pm, Kevin <[email protected]> wrote:
> Recently I finished working on 3 similar jewelry boxes. =A0It's a design
> I have done before with a dovetailed box in the middle suspended
> between two vertical natural edge slabs. =A0Rails across the top and
> bottom of the box are pocket-screwed into the slabs, and the pocket
> holes covered with some decorative pieces. =A0The box houses a number of
> drawers, which may also have some natural edged drawer fronts, so the
> drawers are odd heights. =A0The drawer slides are dadoed into the sides
> of the box, only glued at the front to allow for expansion /
> contraction.
>
> After completing all of them, with the caps glued over the pocket
> holes and finishing complete it was with much chagrin that I noticed
> that the orientation arrow inside the box which ought to be pointing
> up was in fact pointing down. =A0Oh well, flip it over, right? =A0Except
> the slabs on this one were quite nice at the 'top' ends and not very
> nice at all at the 'bottom', with one of them tapering significantly
> so that the back rail was only partially flush to it.
>
> However, on only this one out of the three the drawers were
> symmetrical. =A0So theoretically I could put the drawers in with it
> upside-down. =A0But there was no way that the slides were going to line
> up like that. =A0But what is the harm in trying, right?
>
> They fit almost perfectly.
>
> All I had to do was lower two of them on one side by 1/32" or so. =A0And
> I was able to just barely fit my LV miniature shoulder plane in
> between the slides. =A0So it took all of 2 minutes to fix what would
> have been the biggest mistake I've made all year.
>
> If you are anything like me, at this point you would now be wondering
> when the other shoe was going to drop, because that just doesn't
> happen without something else happening to make up for it. =A0And I
> didn't have to wait long.
>
> The next thing to do was to drill the holes in one of the other ones
> for the knobs. =A0Take a drawer out, mark the center, drill the hole,
> put it back. =A0That's a pretty simple task, eh? =A0One that would really
> cause a problem if you screwed it up, eh? =A0Yeah. =A0On the 4th one I
> went from marking at whatever dimension minus an 1/8th to plus an
> 1/8th.
>
> So I got to sand all those drawer fronts down, make wooden pulls and
> glue them on, and refinish them. =A0And all is right with the universe
> again.
>
> Anyway, here are the three of them:
>
> http://www.etsy.com/listing/62798076/spirit-of-the-woods-ii-jewelry-boxht=
tp://www.etsy.com/listing/62941009/spirit-of-the-woods-iii-jewelry-boxhttp:=
//www.etsy.com/listing/63544321/spirit-of-the-woods-iv-jewelry-box
>
> -Kevin
>
> PS that mini shoulder plane has caused me more pain, it's so darn
> small I keep smacking my hand into stuff, so it's about time its size
> came in handy. =A0Still I wish they made one just like it the same width
> but double the rest. =A0I have the bigger rabbet plane but this one is
> much easier to adjust.
It has always been exciting for me to see 'rough-and-tumble' elegance.
Very hard to categorize (probably impossible anyway) it is an form of
art that I have seen and heard in many disciplines. Stevie Ray Vaughn
is, in terms of technical ability, as rough and crude as it gets. But
he creates warmth with spikes and barbs. A true artist. Early
Picasso... same deal. In a documentary I saw once, he took a simple
brush with black ink and slobbered some shapes and before my very
eyes, they became alive.
Your stuff talks to me that way. Beautiful, just absolutely
gorgeous..... This stuff should be in a gallery somewhere.. like 5th
Ave NYC
Refined like a Keith Moon drum solo.
Nice work, nice design.
On 12/3/2010 11:16 PM, Kevin wrote:
> Recently I finished working on 3 similar jewelry boxes. It's a design
> I have done before with a dovetailed box in the middle suspended
> between two vertical natural edge slabs. Rails across the top and
> bottom of the box are pocket-screwed into the slabs, and the pocket
> holes covered with some decorative pieces. The box houses a number of
> drawers, which may also have some natural edged drawer fronts, so the
> drawers are odd heights. The drawer slides are dadoed into the sides
> of the box, only glued at the front to allow for expansion /
> contraction.
>
> After completing all of them, with the caps glued over the pocket
> holes and finishing complete it was with much chagrin that I noticed
> that the orientation arrow inside the box which ought to be pointing
> up was in fact pointing down. Oh well, flip it over, right? Except
> the slabs on this one were quite nice at the 'top' ends and not very
> nice at all at the 'bottom', with one of them tapering significantly
> so that the back rail was only partially flush to it.
>
> However, on only this one out of the three the drawers were
> symmetrical. So theoretically I could put the drawers in with it
> upside-down. But there was no way that the slides were going to line
> up like that. But what is the harm in trying, right?
>
> They fit almost perfectly.
>
> All I had to do was lower two of them on one side by 1/32" or so. And
> I was able to just barely fit my LV miniature shoulder plane in
> between the slides. So it took all of 2 minutes to fix what would
> have been the biggest mistake I've made all year.
>
> If you are anything like me, at this point you would now be wondering
> when the other shoe was going to drop, because that just doesn't
> happen without something else happening to make up for it. And I
> didn't have to wait long.
>
> The next thing to do was to drill the holes in one of the other ones
> for the knobs. Take a drawer out, mark the center, drill the hole,
> put it back. That's a pretty simple task, eh? One that would really
> cause a problem if you screwed it up, eh? Yeah. On the 4th one I
> went from marking at whatever dimension minus an 1/8th to plus an
> 1/8th.
>
> So I got to sand all those drawer fronts down, make wooden pulls and
> glue them on, and refinish them. And all is right with the universe
> again.
>
> Anyway, here are the three of them:
>
> http://www.etsy.com/listing/62798076/spirit-of-the-woods-ii-jewelry-box
> http://www.etsy.com/listing/62941009/spirit-of-the-woods-iii-jewelry-box
> http://www.etsy.com/listing/63544321/spirit-of-the-woods-iv-jewelry-box
>
>
> -Kevin
>
> PS that mini shoulder plane has caused me more pain, it's so darn
> small I keep smacking my hand into stuff, so it's about time its size
> came in handy. Still I wish they made one just like it the same width
> but double the rest. I have the bigger rabbet plane but this one is
> much easier to adjust.
On Sat, 04 Dec 2010 15:56:59 -0500, Kevin <[email protected]>
wrote:
>On Sat, 4 Dec 2010 05:25:14 -0500, "Lee Michaels"
><leemichaels*nadaspam* at comcast dot net> wrote:
>
>>I don't wish to alarm you but somebody sold you some wood that still had
>>bark on it. And there appears to be some kind of rot or insect infestation
>>in the middle of two of the boxes. Just though you should know.
>>
>><grin, duck and run>
>>
>
>I was hoping no one would catch on to that. I ran out of good wood
>and had to raid the burn pile ;)
>
>But seriously, I think the walnut on the front of one of them was from
>a section most people would have cut out and tossed in the burn pile,
>perhaps with a bit of regret. Big ol' knot and a punky spot
>surrounded by nice figure. On a different day I might not stop to
>save it myself.
Congrats on the restraint and end product, Kevin. Well done.
--
"Human nature itself is evermore an advocate for liberty.
There is also in human nature a resentment of injury, and
indignation against wrong. A love of truth and a veneration
of virtue. These amiable passions, are the latent spark. If
the people are capable of understanding, seeing and feeling
the differences between true and false, right and wrong,
virtue and vice, to what better principle can the friends of
mankind apply than to the sense of this difference?"
--John Adams
On 12/03/10 11:16 PM, Kevin wrote:
> Recently I finished working on 3 similar jewelry boxes. It's a design
> I have done before with a dovetailed box in the middle suspended
> between two vertical natural edge slabs. Rails across the top and
> bottom of the box are pocket-screwed into the slabs, and the pocket
> holes covered with some decorative pieces. The box houses a number of
> drawers, which may also have some natural edged drawer fronts, so the
> drawers are odd heights. The drawer slides are dadoed into the sides
> of the box, only glued at the front to allow for expansion /
> contraction.
>
> After completing all of them, with the caps glued over the pocket
> holes and finishing complete it was with much chagrin that I noticed
> that the orientation arrow inside the box which ought to be pointing
> up was in fact pointing down. Oh well, flip it over, right? Except
> the slabs on this one were quite nice at the 'top' ends and not very
> nice at all at the 'bottom', with one of them tapering significantly
> so that the back rail was only partially flush to it.
>
> However, on only this one out of the three the drawers were
> symmetrical. So theoretically I could put the drawers in with it
> upside-down. But there was no way that the slides were going to line
> up like that. But what is the harm in trying, right?
>
> They fit almost perfectly.
>
> All I had to do was lower two of them on one side by 1/32" or so. And
> I was able to just barely fit my LV miniature shoulder plane in
> between the slides. So it took all of 2 minutes to fix what would
> have been the biggest mistake I've made all year.
>
> If you are anything like me, at this point you would now be wondering
> when the other shoe was going to drop, because that just doesn't
> happen without something else happening to make up for it. And I
> didn't have to wait long.
>
> The next thing to do was to drill the holes in one of the other ones
> for the knobs. Take a drawer out, mark the center, drill the hole,
> put it back. That's a pretty simple task, eh? One that would really
> cause a problem if you screwed it up, eh? Yeah. On the 4th one I
> went from marking at whatever dimension minus an 1/8th to plus an
> 1/8th.
>
> So I got to sand all those drawer fronts down, make wooden pulls and
> glue them on, and refinish them. And all is right with the universe
> again.
>
> Anyway, here are the three of them:
>
> http://www.etsy.com/listing/62798076/spirit-of-the-woods-ii-jewelry-box
> http://www.etsy.com/listing/62941009/spirit-of-the-woods-iii-jewelry-box
> http://www.etsy.com/listing/63544321/spirit-of-the-woods-iv-jewelry-box
>
>
I have one word for you, fucking WOW, that is gorgeous.
--
Froz...
The system will be down for 10 days for preventive maintenance.
On Sun, 05 Dec 2010 23:07:14 -0500, tiredofspam <nospam.nospam.com>
wrote:
>I'm actually doing a night table for my wife and it has similar grain
>and pith.. My problem has been planing by hand. It's been tough the
>grain has not been very friendly to work on. I want the chatoyance, so I
>don't want to sand it. Did you sand or plane?
Drum sander, then random orbit sander. Never went near the planer
with that stuff.
-Kevin
On Sat, 4 Dec 2010 05:25:14 -0500, "Lee Michaels"
<leemichaels*nadaspam* at comcast dot net> wrote:
>I don't wish to alarm you but somebody sold you some wood that still had
>bark on it. And there appears to be some kind of rot or insect infestation
>in the middle of two of the boxes. Just though you should know.
>
><grin, duck and run>
>
I was hoping no one would catch on to that. I ran out of good wood
and had to raid the burn pile ;)
But seriously, I think the walnut on the front of one of them was from
a section most people would have cut out and tossed in the burn pile,
perhaps with a bit of regret. Big ol' knot and a punky spot
surrounded by nice figure. On a different day I might not stop to
save it myself.
-Kevin
I'm actually doing a night table for my wife and it has similar grain
and pith.. My problem has been planing by hand. It's been tough the
grain has not been very friendly to work on. I want the chatoyance, so I
don't want to sand it. Did you sand or plane?
On 12/4/2010 3:56 PM, Kevin wrote:
> On Sat, 4 Dec 2010 05:25:14 -0500, "Lee Michaels"
> <leemichaels*nadaspam* at comcast dot net> wrote:
>
>> I don't wish to alarm you but somebody sold you some wood that still had
>> bark on it. And there appears to be some kind of rot or insect infestation
>> in the middle of two of the boxes. Just though you should know.
>>
>> <grin, duck and run>
>>
>
> I was hoping no one would catch on to that. I ran out of good wood
> and had to raid the burn pile ;)
>
> But seriously, I think the walnut on the front of one of them was from
> a section most people would have cut out and tossed in the burn pile,
> perhaps with a bit of regret. Big ol' knot and a punky spot
> surrounded by nice figure. On a different day I might not stop to
> save it myself.
>
> -Kevin