I made a sanding table years ago from peg board that I enlarged the hole
in and supported the board using small dowels to keep the board level
but not block air flow.
I would like to cover that with a glued on router/sanding pad.
My biggest fear is that spray 77 which I thought of using would just
collect dust, and also get past just the glue-able area to the top of
the pad, rolling on a contact cement would lead to the same.
How should I attach the pad to avoid gumming up the works? Thanks
Thanks both of you. I will give that a try.
On 10/6/2010 12:41 PM, tiredofspam wrote:
> I made a sanding table years ago from peg board that I enlarged the hole
> in and supported the board using small dowels to keep the board level
> but not block air flow.
>
> I would like to cover that with a glued on router/sanding pad.
> My biggest fear is that spray 77 which I thought of using would just
> collect dust, and also get past just the glue-able area to the top of
> the pad, rolling on a contact cement would lead to the same.
>
> How should I attach the pad to avoid gumming up the works? Thanks
My reason is two fold.. laziness for one and the pad creeps around after
a while. I wipe it with alcohol or water to clean on a cloth to clean it.
The sanding table is removeable, so instead of having to setup the top
on the bench and then add the pad, I just figured being sheer lazy and
wanting to do the work and not have to spread out the mat that I would
just glue it on.
On 10/7/2010 6:00 PM, Leon wrote:
> "tiredofspam"<nospam.nospam.com> wrote in message
> news:[email protected]...
>> I made a sanding table years ago from peg board that I enlarged the hole in
>> and supported the board using small dowels to keep the board level but not
>> block air flow.
>>
>> I would like to cover that with a glued on router/sanding pad.
>> My biggest fear is that spray 77 which I thought of using would just
>> collect dust, and also get past just the glue-able area to the top of the
>> pad, rolling on a contact cement would lead to the same.
>>
>> How should I attach the pad to avoid gumming up the works? Thanks
>
> Think about what the function of a router/sanding pad is.....Why would you
> want to glue down a pad that naturally does not want to move?
> So your answer might be because as it gets loaded with dust it becomes less
> effective in holding itself and or things that you put on it in place. So
> again I ask why would you want to glue down a router pad?
>
> Seems the suction of the sanding table should keep the pad in place..
>
> I used router/sanding pads for years to cushion my work from the hard work
> surface and they worked fine but now I prefer to use the Bench Cookies that
> Rockler sells.
>
>
"tiredofspam" <nospam.nospam.com> wrote in message
news:[email protected]...
> My reason is two fold.. laziness for one and the pad creeps around after a
> while. I wipe it with alcohol or water to clean on a cloth to clean it.
Whel ther is nothing wrong with being lazy. ;~) but if you glue it down to
tyour peg board, using water to clean it will be a thing of the past. I
find that tossing the pad in the washer cleanis it pretty good.
>
> The sanding table is removeable, so instead of having to setup the top on
> the bench and then add the pad, I just figured being sheer lazy and
> wanting to do the work and not have to spread out the mat that I would
> just glue it on.
"tiredofspam" <nospam.nospam.com> wrote in message
news:[email protected]...
>I made a sanding table years ago from peg board that I enlarged the hole in
>and supported the board using small dowels to keep the board level but not
>block air flow.
>
> I would like to cover that with a glued on router/sanding pad.
> My biggest fear is that spray 77 which I thought of using would just
> collect dust, and also get past just the glue-able area to the top of the
> pad, rolling on a contact cement would lead to the same.
>
> How should I attach the pad to avoid gumming up the works? Thanks
Think about what the function of a router/sanding pad is.....Why would you
want to glue down a pad that naturally does not want to move?
So your answer might be because as it gets loaded with dust it becomes less
effective in holding itself and or things that you put on it in place. So
again I ask why would you want to glue down a router pad?
Seems the suction of the sanding table should keep the pad in place..
I used router/sanding pads for years to cushion my work from the hard work
surface and they worked fine but now I prefer to use the Bench Cookies that
Rockler sells.
On Wed, 06 Oct 2010 12:41:02 -0400, tiredofspam <nospam.nospam.com> wrote:
>I made a sanding table years ago from peg board that I enlarged the hole
>in and supported the board using small dowels to keep the board level
>but not block air flow.
>
>I would like to cover that with a glued on router/sanding pad.
>My biggest fear is that spray 77 which I thought of using would just
>collect dust, and also get past just the glue-able area to the top of
>the pad, rolling on a contact cement would lead to the same.
>
>How should I attach the pad to avoid gumming up the works? Thanks
I use a pad on mine, actually the stuff they sell to make shelves non-skid, cuz
I'm cheap..
I find that the pad tends to cling to the pegboard by itself, so I just lay it
on the surface and tack the corners down..
Just a note... the pad does decrease the air flow to the DC..
mac
Please remove splinters before emailing
On 10/6/10 11:41 AM, tiredofspam wrote:
> I made a sanding table years ago from peg board that I enlarged the hole
> in and supported the board using small dowels to keep the board level
> but not block air flow.
>
> I would like to cover that with a glued on router/sanding pad.
> My biggest fear is that spray 77 which I thought of using would just
> collect dust, and also get past just the glue-able area to the top of
> the pad, rolling on a contact cement would lead to the same.
>
> How should I attach the pad to avoid gumming up the works? Thanks
Find a self adhesive pad.
Spray just the pad and apply it while the glue is still wet.
--
-MIKE-
"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com
[email protected]
---remove "DOT" ^^^^ to reply
I make sails. Sails are held together with double sided tape then sewn
through cloth, tape and all. Sometimes there is some stickiness at the seams
that could easily pick up dirt and look bad. My solution is to dust the
finished seams with talcum powder and then brush it off. The talc dust takes
away the stickiness and is so thin it can't be seen. Go ahead and use the
spray. The first time you use the sanding table, it will take care of
itself.
"tiredofspam" <nospam.nospam.com> wrote in message
news:[email protected]...
>I made a sanding table years ago from peg board that I enlarged the hole in
>and supported the board using small dowels to keep the board level but not
>block air flow.
>
> I would like to cover that with a glued on router/sanding pad.
> My biggest fear is that spray 77 which I thought of using would just
> collect dust, and also get past just the glue-able area to the top of the
> pad, rolling on a contact cement would lead to the same.
>
> How should I attach the pad to avoid gumming up the works? Thanks