The exterior doors on my four-year-old home have started to rot. In true
woodworker fashion I decided to rebuild the doors. I even decided to
redesign the doors into french doors.
I have rebuilt the door frames and repaired the doors; then I ordered a
t astrigal to seal between the doors.
Here is my problem, do any of you fine people know the proper way to
install this thing? It is just slightly longer than the door (maybe an inch
or less) but if I cut it the flush bolts will not line up with the
predrilled holes.
I purchased the thing from a local door manufacturer and the smug little
salesman
laughed when I told him I was going to install it myself. As I was leaving
he yelled "good luck" and I am sure he made some type of "he'll be back"
comment.
Now I realize I am probably being arrogant and maybe even
foolish....but...damn-it I'm an American, and I don't like be told I can't
do something; especially by some sniveling sales puke that probably doesn't
know how to hold a hammer.
So fellow woodworkers, give me some advice or websites or something. You
see, even though this tough old American isn't afraid of any salesman, my
wife hates the plywood covered hole in our living room, and I am scared to
death of her.
>> Here is my problem, do any of you fine people know the proper way to
>>install this thing? It is just slightly longer than the door (maybe an
>>inch
>>or less) but if I cut it the flush bolts will not line up with the
>>predrilled holes.
You'll probably have to trim a bit off both the top and the bottom, and if
you don't have enough ground clearance to to line up the holes you'll have
to remove the door.
I worked in a door shop for about 14 years but I'm a little confused with
your question. You state the predrilled holes for the flush bolts won't
line up if you cut the astragal off. If you mean the holes in the sill and
header of the frame, cutting or not cutting the astragal isn't going to
change the position of the pins on the flush bolts. If it's a wooden
astragal and you actually mean the premortise for the flushbolts themselves
then you can cut the astragal off and lengthen the mortise with either a
router or use a forstner bit in your drill press and a bandsaw. If you are
talking about a metal product there should be a strip of plastic that snaps
into a channel that can be removed and trimmed. The flush bolt can then be
moved and repositioned.. hopefully.... depending on who the manufacturer is.
If it is actually the holes in the sill and the header of the frame causing
you trouble then plug the holes in the header with a dowell and glue. cut
some slivers of wood to drive into the screw holes with some glue and trim
flush.. then redrill in the position you need. If you have a wood sill do
the same there.... if it's metal get a small piece of flat aluminum and make
yourself a plate wide enough to cover the existing holes and drill where
needed.
On Thu, 28 Oct 2004 21:50:59 -0500, "Ron" <[email protected]>
wrote:
> The exterior doors on my four-year-old home have started to rot. In true
>woodworker fashion I decided to rebuild the doors. I even decided to
>redesign the doors into french doors.
> I have rebuilt the door frames and repaired the doors; then I ordered a
>t astrigal to seal between the doors.
> Here is my problem, do any of you fine people know the proper way to
>install this thing? It is just slightly longer than the door (maybe an inch
>or less) but if I cut it the flush bolts will not line up with the
>predrilled holes.
> I purchased the thing from a local door manufacturer and the smug little
>salesman
>laughed when I told him I was going to install it myself. As I was leaving
>he yelled "good luck" and I am sure he made some type of "he'll be back"
>comment.
> Now I realize I am probably being arrogant and maybe even
>foolish....but...damn-it I'm an American, and I don't like be told I can't
>do something; especially by some sniveling sales puke that probably doesn't
>know how to hold a hammer.
> So fellow woodworkers, give me some advice or websites or something. You
>see, even though this tough old American isn't afraid of any salesman, my
>wife hates the plywood covered hole in our living room, and I am scared to
>death of her.
>
get her to do it?
OK, bad idea.
I'm used to an astragal being a wood molding used to finish the join
between two doors. it sounds like you are talking about a metal
product. can you find a name of it anywhere? posting a link to a
picture somewhere on the web would be helpful.
Cut it the same length as the door and let the weatherstripping do the rest.
It usually goes on the 'fixed" door.
"Ron" <[email protected]> wrote in message
news:[email protected]...
> The exterior doors on my four-year-old home have started to rot. In
true
> woodworker fashion I decided to rebuild the doors. I even decided to
> redesign the doors into french doors.
> I have rebuilt the door frames and repaired the doors; then I ordered
a
> t astrigal to seal between the doors.
> Here is my problem, do any of you fine people know the proper way to
> install this thing? It is just slightly longer than the door (maybe an
inch
> or less) but if I cut it the flush bolts will not line up with the
> predrilled holes.
> I purchased the thing from a local door manufacturer and the smug
little
> salesman
> laughed when I told him I was going to install it myself. As I was leaving
> he yelled "good luck" and I am sure he made some type of "he'll be back"
> comment.
> Now I realize I am probably being arrogant and maybe even
> foolish....but...damn-it I'm an American, and I don't like be told I can't
> do something; especially by some sniveling sales puke that probably
doesn't
> know how to hold a hammer.
> So fellow woodworkers, give me some advice or websites or something.
You
> see, even though this tough old American isn't afraid of any salesman, my
> wife hates the plywood covered hole in our living room, and I am scared to
> death of her.
>
>
In article <[email protected]>,
"Ron" <[email protected]> wrote:
> The exterior doors on my four-year-old home have started to rot.
If you haven't done so already, you need to figure out why your doors
only lasted 4 years and remedy that situation before you go about
building new doors.
--
Owen Lowe and his Fly-by-Night Copper Company
____
"To know the world intimately is the beginning of caring."
-- Ann Hayman Zwinger