You can also use a router on a table with an off set fence, a router with a
pattern bit or bushing guide and a straight edge, a straight edge guide
along a table saw fence, or, maybe it is time to develop the skill, it isn't
something the good fairy is going to leave under your pillow.
--
Mike G.
Heirloom Woods
www.heirloom-woods.net
"spiderrman" <[email protected]> wrote in message
news:[email protected]...
> Granted.
> But with this process there is a certain amount of skill involved
> which I do not process yet.
>
> S
>
> On Sun, 19 Oct 2003 03:44:18 GMT, "danh"
> <[email protected]> wrote:
>
> >Used Jointer hand plane
> >
> >
> >"spiderrman" <[email protected]> wrote in message
> >news:[email protected]...
> >> Howdy all,
> >> Short of buying a joiner, what is the most economical way to put a
> >> good jointed edge on pieces you're planning to glue together. (Making
> >> a panel. say)
> >>
> >> S
> >
>
I suppose you could do it the same way you deal with curved boards:
Clamp it to a know straight board, and run that board along the fence of a
TS to get a clean edge. Then you can simply turn it around and run the
freshly cut edge directly against the fence to make the opposite edge
parallel.
If you have a good blade you will have two good gluable edges.
"spiderrman" <[email protected]> wrote in message
news:[email protected]...
> Howdy all,
> Short of buying a joiner, what is the most economical way to put a
> good jointed edge on pieces you're planning to glue together. (Making
> a panel. say)
>
> S
If your board is shorter than a piece of plywood, cut a piece of plywood out
of a sheet of plywood 8' long and a bit wider that the piece of wood you
want to joint. Screw down or clamp the wood on top of that piece of plywood
with the waste edge hanging over the edge closest to the blade. Use the
opposite edge of the plywood as the guide against the fence.
"spiderrman" <[email protected]> wrote in message
news:[email protected]...
> Howdy all,
> Short of buying a joiner, what is the most economical way to put a
> good jointed edge on pieces you're planning to glue together. (Making
> a panel. say)
>
> S
Use a Forrest WW2 saw blade in yer table saw.
Man that thing leaves a nice edge!
Saw-marks?!? what are those?!?
mikey.
spiderrman wrote:
> Howdy all,
> Short of buying a joiner, what is the most economical way to put a
> good jointed edge on pieces you're planning to glue together. (Making
> a panel. say)
>
> S
spiderrman wrote:
>>> Short of buying a joiner, what is the most economical way to put a
>>> good jointed edge on pieces you're planning to glue together. (Making
>>> a panel. say)
>>Used Jointer hand plane
> Granted.
> But with this process there is a certain amount of skill involved
> which I do not process yet.
So acquire them! :)
I'm in the process of learning how to do just that. I started out because I
can't afford a jointer (no room, no money) but now that I'm getting into
it, I really enjoy working with hand planes. There's something gratifying
about the gentle shick, shick, shick of it all.
The learning curve is pretty steep though. Before you can use the plane,
you have to figure out how to adjust, and most importantly, how to
*sharpen* the plane. That's half of the battle right there.
--
Michael McIntyre ---- Silvan <[email protected]>
Linux fanatic, and certified Geek; registered Linux user #243621
http://www.geocities.com/Paris/Rue/5407/
Larry Jaques wrote:
> Clamp a dowel to the cheek and angle the plane slightly to put the
> iron all the way across the edge. If you pay attention to what you're
> trying to accomplish, you'll quickly get a nicely jointed edge.
Hmmm... I can see that. Cheaper'n that $40 jointing fence gizmo too.
I'll have to try it.
--
Michael McIntyre ---- Silvan <[email protected]>
Linux fanatic, and certified Geek; registered Linux user #243621
http://www.geocities.com/Paris/Rue/5407/
Granted.
But with this process there is a certain amount of skill involved
which I do not process yet.
S
On Sun, 19 Oct 2003 03:44:18 GMT, "danh"
<[email protected]> wrote:
>Used Jointer hand plane
>
>
>"spiderrman" <[email protected]> wrote in message
>news:[email protected]...
>> Howdy all,
>> Short of buying a joiner, what is the most economical way to put a
>> good jointed edge on pieces you're planning to glue together. (Making
>> a panel. say)
>>
>> S
>
On Sun, 19 Oct 2003 03:58:15 GMT, spiderrman <[email protected]>
pixelated:
>Granted.
>But with this process there is a certain amount of skill involved
>which I do not process yet.
Clamp a dowel to the cheek and angle the plane slightly to put the
iron all the way across the edge. If you pay attention to what you're
trying to accomplish, you'll quickly get a nicely jointed edge.
-------------------------------------------------------
Have you read the new book "What Would Machiavelli Do?"
----------------------------
http://diversify.com Dynamic, Interactive Websites!
--------------------------------------------------------
Used Jointer hand plane
"spiderrman" <[email protected]> wrote in message
news:[email protected]...
> Howdy all,
> Short of buying a joiner, what is the most economical way to put a
> good jointed edge on pieces you're planning to glue together. (Making
> a panel. say)
>
> S