http://www.garrettwade.com/jump.jsp?lGen=detail&itemID=105774&itemType=PRODUCT&iMainCat=0&iSubCat=0&iProductID=105774
It says "Drilling holes for the recess of screw heads and other joinery and
then cutting plugs to fill the hole is a frequent woodworking task. And it
is best done with matched tooling designed for this purposes"
But the two pieces would cut pretty much the same hole; a plug cut with one
will be way too small to fill the recess cut by the other.
Either I am really dumb, or their catalog is screwed up.(Okay, the smart
money is on the first possibility)
Any idea how these are used?
I think you missed the part about "matched sets". One for cutting the plug,
one for making the hole to accept the plug.
Bob S.
"toller" <[email protected]> wrote in message
news:[email protected]...
>
http://www.garrettwade.com/jump.jsp?lGen=detail&itemID=105774&itemType=PRODUCT&iMainCat=0&iSubCat=0&iProductID=105774
>
> It says "Drilling holes for the recess of screw heads and other joinery
and
> then cutting plugs to fill the hole is a frequent woodworking task. And it
> is best done with matched tooling designed for this purposes"
>
> But the two pieces would cut pretty much the same hole; a plug cut with
one
> will be way too small to fill the recess cut by the other.
> Either I am really dumb, or their catalog is screwed up.(Okay, the smart
> money is on the first possibility)
>
> Any idea how these are used?
>
>
> I think you missed the part about "matched sets". One for cutting the
plug,
> one for making the hole to accept the plug.
No, I got that. They both cut about the same sort of hole, and the same
size.
I expected one would cut a small hole, and the other would cut a plug to fit
it, but they don't. Or, at least I can't see how they do.
"toller" <[email protected]> wrote in message
news:[email protected]...
>
http://www.garrettwade.com/jump.jsp?lGen=detail&itemID=105774&itemType=PRODUCT&iMainCat=0&iSubCat=0&iProductID=105774
>
> It says "Drilling holes for the recess of screw heads and other joinery
and
> then cutting plugs to fill the hole is a frequent woodworking task. And it
> is best done with matched tooling designed for this purposes"
>
> But the two pieces would cut pretty much the same hole; a plug cut with
one
> will be way too small to fill the recess cut by the other.
> Either I am really dumb, or their catalog is screwed up.(Okay, the smart
> money is on the first possibility)
>
> Any idea how these are used?
It says: ""Drilling holes for the recess of screw heads and other joinery ",
keyword is "drill"
Holes are made with a regular drill bit, then if you are hiding a screw,
using a plug cutter (4 cutters at the rear of the box) cut a plug that you
would use to insert on the drilled hole or if you are joining two pieces of
wood, use a dowel or tenon cutter (the 4 cutters at the front of the box)
and cut the tenon on the piece you are joining to the first (the mortise
would be the hole made with the drill bit). The dowel/tenon cutter can also
cut plugs, but the plug made with the plug cutter are slightly tapered (I
think) and would get a better fit.
Ok, look here:
http://www.leevalley.com/wood/page.asp?page=32320&category=1,180,42288&ccurrency=2&SID=
if that doesn't take you to the right page, the go to
http://www.leevalley.com , select Us, then Woodworking, then Drilling, then
Dowel, Plug & Tenon Cutters, then Snug-Plug Cutters to see a picture that
will give you a better idea. The graphic shows the difference between a
regular plug cutter and a tapered plug cutter which should help you
understand.
Bob S.
"toller" <[email protected]> wrote in message
news:[email protected]...
>
> > I think you missed the part about "matched sets". One for cutting the
> plug,
> > one for making the hole to accept the plug.
>
> No, I got that. They both cut about the same sort of hole, and the same
> size.
> I expected one would cut a small hole, and the other would cut a plug to
fit
> it, but they don't. Or, at least I can't see how they do.
>
>
These sets cut plugs to fit into previously drilled holes. Drill a hole
with your set of drill bits that match the plug size cut by these cutters.
Typically for a #10 sized screw and smaller a 3/8" diameter hole cut with a
brad point or forstner bit work well. Then use the 3/8" plug cutter to cut
a plug for that hole./
"toller" <[email protected]> wrote in message
news:[email protected]...
>
http://www.garrettwade.com/jump.jsp?lGen=detail&itemID=105774&itemType=PRODUCT&iMainCat=0&iSubCat=0&iProductID=105774
>
> It says "Drilling holes for the recess of screw heads and other joinery
and
> then cutting plugs to fill the hole is a frequent woodworking task. And it
> is best done with matched tooling designed for this purposes"
>
> But the two pieces would cut pretty much the same hole; a plug cut with
one
> will be way too small to fill the recess cut by the other.
> Either I am really dumb, or their catalog is screwed up.(Okay, the smart
> money is on the first possibility)
>
> Any idea how these are used?
>
>
"toller" writes:
> It says "Drilling holes for the recess of screw heads and other joinery
and
> then cutting plugs to fill the hole is a frequent woodworking task. And it
> is best done with matched tooling designed for this purposes"
Fuller makes a nice set available thru Jamestown Distributors.
Supplied with tapered drills, c'sinks, depth collars and plug cutters.
The set I use handles #6 thru #12 flat head wood screws.
HTH
Lew
"toller" <[email protected]> wrote in message
news:[email protected]...
>
http://www.garrettwade.com/jump.jsp?lGen=detail&itemID=105774&itemType=PRODUCT&iMainCat=0&iSubCat=0&iProductID=105774
>
> It says "Drilling holes for the recess of screw heads and other joinery
and
> then cutting plugs to fill the hole is a frequent woodworking task. And it
> is best done with matched tooling designed for this purposes"
>
> But the two pieces would cut pretty much the same hole; a plug cut with
one
> will be way too small to fill the recess cut by the other.
> Either I am really dumb, or their catalog is screwed up.(Okay, the smart
> money is on the first possibility)
>
> Any idea how these are used?
It says: ""Drilling holes for the recess of screw heads and other joinery ",
keyword is "drill"
Holes are made with a regular drill bit, then if you are hiding a screw,
using a plug cutter (4 cutters at the rear of the box) cut a plug that you
would use to insert on the drilled hole or if you are joining two pieces of
wood, use a dowel or tenon cutter (the 4 cutters at the front of the box)
and cut the tenon on the piece you are joining to the first (the mortise
would be the hole made with the drill bit). The dowel/tenon cutter can also
cut plugs, but the plug made with the plug cutter are slightly tapered (I
think) and would get a better fit.