Is there a 3/4" attachment for the Delta mortiser out there somewhere? I
did a quick search of the usual sources, but only found CMT with a 3/4
diameter shank. Unfortunately the Delta has a 5/8 shank. I'd need to make a
lot of 3/4 square openings (too many to chisel) and I'd rather do it in one
shot, as opposed to using the 1/2" and scooting it over. Anyone know whether
these exist? Thanks, Mark
On Mar 23, 1:22 pm, "mark" <[email protected]> wrote:
> Is there a 3/4" attachment for the Delta mortiser out there somewhere? I
> did a quick search of the usual sources, but only found CMT with a 3/4
> diameter shank. Unfortunately the Delta has a 5/8 shank. I'd need to make a
> lot of 3/4 square openings (too many to chisel) and I'd rather do it in one
> shot, as opposed to using the 1/2" and scooting it over. Anyone know whether
> these exist? Thanks, Mark
I've picked up a few on ebay. it takes a while at the rate I lurk the
'bay, but I've gotten some good deals.
replying to bridgerfafc, Dan wrote:
> bridgerfafc wrote:
>
> I've picked up a few on ebay. it takes a while at the rate I lurk the
> 'bay, but I've gotten some good deals.
eBay has a bushing that fits a 3/4" shank bit the bushing allows you to
use a 3/4" shank bit in the delta mortiser.
--
posted from
http://www.homeownershub.com/woodworking/3-4-hollow-chisel-mortising-attachment-for-a-delta-mortiser-419362-.htm
using HomeOwnersHub's Web, RSS and Social Media Interface
to home and garden related groups
On Sun, 23 Mar 2008 15:22:04 -0500, "mark" <[email protected]> wrote:
>Is there a 3/4" attachment for the Delta mortiser out there somewhere? I
>did a quick search of the usual sources, but only found CMT with a 3/4
>diameter shank. Unfortunately the Delta has a 5/8 shank. I'd need to make a
>lot of 3/4 square openings (too many to chisel) and I'd rather do it in one
>shot, as opposed to using the 1/2" and scooting it over. Anyone know whether
>these exist?
My Powermatic chisels have a 3/4" shank.
What about replacing your chuck with a 3/4" chuck?
"Bonehenge (B A R R Y)" <[email protected]> wrote in message
news:[email protected]...
> On Sun, 23 Mar 2008 15:22:04 -0500, "mark" <[email protected]> wrote:
>
>>Is there a 3/4" attachment for the Delta mortiser out there somewhere? I
>>did a quick search of the usual sources, but only found CMT with a 3/4
>>diameter shank. Unfortunately the Delta has a 5/8 shank. I'd need to make
>>a
>>lot of 3/4 square openings (too many to chisel) and I'd rather do it in
>>one
>>shot, as opposed to using the 1/2" and scooting it over. Anyone know
>>whether
>>these exist?
>
> My Powermatic chisels have a 3/4" shank.
>
> What about replacing your chuck with a 3/4" chuck?
Would rather find a chisel that will fit the existing chuck. But not ruling
out the larger chuck.....
<[email protected]> wrote in message
news:[email protected]...
> On Mar 23, 1:22 pm, "mark" <[email protected]> wrote:
>> Is there a 3/4" attachment for the Delta mortiser out there somewhere? I
>> did a quick search of the usual sources, but only found CMT with a 3/4
>> diameter shank. Unfortunately the Delta has a 5/8 shank. I'd need to
>> make a
>> lot of 3/4 square openings (too many to chisel) and I'd rather do it in
>> one
>> shot, as opposed to using the 1/2" and scooting it over. Anyone know
>> whether
>> these exist? Thanks, Mark
>
> I've picked up a few on ebay. it takes a while at the rate I lurk the
> 'bay, but I've gotten some good deals.
Jeez, why is it I never think about Ebay??? Thanks