If you could get something like an old or cheap new dartboard that would be
practically indestructable for this sort of application. The wires can be
removed fairly easily and then you'd only have to deal with it being round
:).
"Morris Dovey" <[email protected]> wrote in message
news:[email protected]...
> Roy Smith wrote:
> | In article <[email protected]>,
> | "Morris Dovey" <[email protected]> wrote:
> |
> || Roy Smith wrote:
> ||| Pardon me for what's probably a silly question. I'm looking for a
> ||| wood that's easy to stick tacks or push-pins into (by hand), but
> ||| more substantial than cork or balsa. Any suggestions?
> ||
> || How easy?
> |
> | A plain old notice board for a public area. I'm just worried that
> | cork will get beat up quickly.
>
> I think I'd be seriously tempted to glue 1/8" cork over something like
> fiberboard. Several people have suggested end-grain solutions, an idea
> I like, but I'm not sure that end-grain slices will heal as well as
> I'd expect the cork to do.
>
> [ Not believing that no one was willing to play straight man and ask:
> "What's a 'split'?" Ah, well... ]
>
> --
> Morris Dovey
> DeSoto Solar
> DeSoto, Iowa USA
> http://www.iedu.com/DeSoto/
>
>
On Tue, 17 Jul 2007 16:22:34 -0400, Roy Smith <[email protected]> wrote:
>Pardon me for what's probably a silly question. I'm looking for a wood
>that's easy to stick tacks or push-pins into (by hand), but more
>substantial than cork or balsa. Any suggestions?
There are many. Pine is usually available cheap most places. Most
softwoods should work well. I use an old piece of Styrofoam to keep a
few pins in my shop.
Roy,
Forget using wood. Get a sheet of 'Homosote' {spelling ?}. Cut to size, slap
on a couple of coats 'Sealer & Primer' of your choice. Then give it a couple
of coats of the water-based finish of your choice.
A few years ago I taught Marksmanship at a summer camp. This was their
'public' bulletin board. Exposed to all kinds of weather, just gave it a
fresh coat of paint when it got to 'holey'. Absolutely dirt cheap and I know
it lasted at least 2 years . . . probably more.
Regards & Good Luck,
Ron Magen
Backyard Boatshop
"Roy Smith" <[email protected]> wrote in message >
> > Roy Smith wrote:
> > | Pardon me for what's probably a silly question. I'm looking for a
> > | wood that's easy to stick tacks or push-pins into (by hand), but
> > | more substantial than cork or balsa. Any suggestions?
> >
SNIP
> A plain old notice board for a public area. I'm just worried that cork
> will get beat up quickly.
Roy Smith wrote:
| Pardon me for what's probably a silly question. I'm looking for a
| wood that's easy to stick tacks or push-pins into (by hand), but
| more substantial than cork or balsa. Any suggestions?
How easy?
white pine, date palm
Of course, for _real_ easy it's hard to beat carefully kiln-dried
banana wood. The problem is that it isn't usually available in
boards - generally it's sold in 'splits'.
--
Morris Dovey
DeSoto Solar
DeSoto, Iowa USA
http://www.iedu.com/DeSoto/
Roy Smith wrote:
| In article <[email protected]>,
| "Morris Dovey" <[email protected]> wrote:
|
|| Roy Smith wrote:
||| Pardon me for what's probably a silly question. I'm looking for a
||| wood that's easy to stick tacks or push-pins into (by hand), but
||| more substantial than cork or balsa. Any suggestions?
||
|| How easy?
|
| A plain old notice board for a public area. I'm just worried that
| cork will get beat up quickly.
I think I'd be seriously tempted to glue 1/8" cork over something like
fiberboard. Several people have suggested end-grain solutions, an idea
I like, but I'm not sure that end-grain slices will heal as well as
I'd expect the cork to do.
[ Not believing that no one was willing to play straight man and ask:
"What's a 'split'?" Ah, well... ]
--
Morris Dovey
DeSoto Solar
DeSoto, Iowa USA
http://www.iedu.com/DeSoto/
Lew Hodgett <[email protected]> wrote in news:RuLni.10008$zA4.5718
@newsread3.news.pas.earthlink.net:
*snip*
>
> I also had a board hanging on the wall of my home office for years.
>
> Lew
I've threatened to do that a couple times! My mother complains about my
use of a table top as an um, table top. (Beautiful as it may be.) We've
got more of that particular wood, next time she complains I'll probably
oil it and put some up on the wall.
:-)
Puckdropper
--
Wise is the man who attempts to answer his question before asking it.
To email me directly, send a message to puckdropper (at) fastmail.fm
On Tue, 17 Jul 2007 16:22:34 -0400, Roy Smith <[email protected]> wrote:
>Pardon me for what's probably a silly question. I'm looking for a wood
>that's easy to stick tacks or push-pins into (by hand), but more
>substantial than cork or balsa. Any suggestions?
Might depend on how big the notice board or whatever is...
For a fairly small area or a large budget, I'd go with the pine or basswood,
probably end grain..
For larger, less expensive applications, I'd use an inexpensive fiberboard
bulletin board (no use re-inventing the wheel) with a replaceable skin of thin
wood, like those door skins they sell at the Borg..
The fiber will hold up to push pins for years and the wood skin would be nice
looking and easy to replace whenever it needs it..
mac
Please remove splinters before emailing
One thing about cork... it's pretty much self healing.
Wood on the other hand will gather holes like crazy and eventualy splinter
and chip.
I'd find some good quality cork and put a lovely wooden frame around it.
Kate
______
/l ,[____],
l-L -OlllllllO-
()_)-()_)--)_)
"Roy Smith" <[email protected]> wrote in message
news:[email protected]...
Pardon me for what's probably a silly question. I'm looking for a wood
that's easy to stick tacks or push-pins into (by hand), but more
substantial than cork or balsa. Any suggestions?
In article <[email protected]>, Roy Smith <[email protected]> wrote:
>Pardon me for what's probably a silly question. I'm looking for a wood
>that's easy to stick tacks or push-pins into (by hand), but more
>substantial than cork or balsa. Any suggestions?
Sugar pine, basswood, aspen, redwood
--
Regards,
Doug Miller (alphageek at milmac dot com)
It's time to throw all their damned tea in the harbor again.
End grain basswood
"Roy Smith" <[email protected]> wrote in message
news:[email protected]...
> Pardon me for what's probably a silly question. I'm looking for a wood
> that's easy to stick tacks or push-pins into (by hand), but more
> substantial than cork or balsa. Any suggestions?
In article <[email protected]>,
"Morris Dovey" <[email protected]> wrote:
> Roy Smith wrote:
> | Pardon me for what's probably a silly question. I'm looking for a
> | wood that's easy to stick tacks or push-pins into (by hand), but
> | more substantial than cork or balsa. Any suggestions?
>
> How easy?
A plain old notice board for a public area. I'm just worried that cork
will get beat up quickly.