I am working (slowly) on a workbench and was wondering if there is a reason
on not using oak for the top? Other than it's not as hard as maple.
I have a bunch of 8/4 oak and want to make the top out of this wood, I like
oak as my favorite wood so that is why the question.....Brian
--
www.members.cox.net/bsnikitas
Brian In Hampton wrote:
> I am working (slowly) on a workbench and was wondering if there is a
> reason on not using oak for the top? Other than it's not as hard as maple.
> I have a bunch of 8/4 oak and want to make the top out of this wood, I
> like oak as my favorite wood so that is why the question.....Brian
>
> --
> www.members.cox.net/bsnikitas
If you are the adventrous type, make the top up out of 1 1/2 strips of oak,
glued up face to face. About 36 strips will give you a nice 28" top with
the side grain showing. Looks nice and removes the splinter problem.
You will want a hand power plane and a good belt sander, as well as three
men and a boy to move it, but makes a nice stable top.
Deb
On Wed, 13 Apr 2005 20:49:54 -0400, "Brian In Hampton"
<[email protected]> wrote:
>I am working (slowly) on a workbench and was wondering if there is a reason
>on not using oak for the top? Other than it's not as hard as maple.
>I have a bunch of 8/4 oak and want to make the top out of this wood, I like
>oak as my favorite wood so that is why the question.....Brian
Lots of people use oak. The short grain of maple has its advantages,
but any hardwood you can get cheap is good. Go for it.
-Leuf
>I am working (slowly) on a workbench and was wondering if there is a reason
> on not using oak for the top? Other than it's not as hard as maple.
> I have a bunch of 8/4 oak and want to make the top out of this wood, I like
> oak as my favorite wood so that is why the question.....Brian
>
> --
> www.members.cox.net/bsnikitas
>
>
Any standard Oak, red or white, and Ash (too soft) are both too open
grained, closed grained is what you want like hard or soft Maple and
Euro or American Beech. Euro Beech and hard rock sugar maple are
the best for the job, though as well Ipe (Pao Lope) decking boards
(harder, common) could be ripped and laminated together with epoxy,
but it would be harder on the cutting edges of hand tools. Southern
Yellow Pine (SYP) would be a good choice if you can get it, so
would Osage Orange.
If you use the Oak you would save bucks. When the top becomes worn,
deeply nicked too much and grain becomes more open from wear, you
would hand plane it down, therefore make it a thick top to begin with,
like 3". It will still last you for many years anyway, so don't sweat it. The
Oak is definitely hard and strong enough to do the job.
--
Alex - newbie_neander in woodworking
cravdraa_at-yahoo_dot-com
not my site: http://www.e-sword.net/
woodworker88 wrote:
>
> The only problem I could forsee with oak is possible difficulties with
> fasteners for building the bench ie attaching the legs to the top. I
> have had some bad experiences with oak cabinets, moulding, etc, and I
> could only see these problems being a much bigger deal on larger pieces
> such as a bench top.
What kind of problems of which you speaketh???
"Brian In Hampton"
>I am working (slowly) on a workbench and was wondering if there is a reason
> on not using oak for the top? Other than it's not as hard as maple.
> I have a bunch of 8/4 oak and want to make the top out of this wood, I
> like
> oak as my favorite wood so that is why the question.
Oak, if I had the quantities on-hand as you have, I would definitely build a
bench from it. Avoid using the wide growth rings flat.
Dave
Posted Via Usenet.com Premium Usenet Newsgroup Services
----------------------------------------------------------
** SPEED ** RETENTION ** COMPLETION ** ANONYMITY **
----------------------------------------------------------
http://www.usenet.com
Maple and Beech are traditional and may offer some advantages....but oak
will work fine.
I started on one myself this past week end, top will be ash, base will be
oak. I'm replacing a bench I made 25 years ago. The top was build up using 2
layers of particle board, then a layer of 4/4 oak. Lots of character.
"Brian In Hampton" <[email protected]> wrote in message
news:P6j7e.39$Zr.23@lakeread08...
> I am working (slowly) on a workbench and was wondering if there is a
reason
> on not using oak for the top? Other than it's not as hard as maple.
> I have a bunch of 8/4 oak and want to make the top out of this wood, I
like
> oak as my favorite wood so that is why the question.....Brian
>
> --
> www.members.cox.net/bsnikitas
>
>
> Maple and Beech are traditional and may offer some advantages....but oak
> will work fine.
>
> I started on one myself this past week end, top will be ash, base will be
> oak. I'm replacing a bench I made 25 years ago. The top was build up using 2
> layers of particle board, then a layer of 4/4 oak. Lots of character.
>
>
I would go the other way and reverse the two, that Oak is harder than the Ash.
--
Alex - newbie_neander in woodworking
cravdraa_at-yahoo_dot-com
not my site: http://www.e-sword.net/
In article <[email protected]>,
[email protected] says...
> On Wed, 13 Apr 2005 20:49:54 -0400, "Brian In Hampton"
> <[email protected]> wrote:
>
> >I have a bunch of 8/4 oak and want to make the top out of this wood, I like
> >oak as my favorite wood so that is why the question.....Brian
>
> Lots of people use oak. The short grain of maple has its advantages,
> but any hardwood you can get cheap is good. Go for it.
>
One suggestion that I picked up from an article in a very old FWW. Put
an edge of softer wood around the top. That way it'll get dinged
instead of the prize project you just bumped against it :-). I used
redwood 2x4s.
--
Homo sapiens is a goal, not a description
"Dr. Deb" <[email protected]> wrote :
> Brian In Hampton wrote:
>
>> I am working (slowly) on a workbench and was wondering if there is a
>> reason on not using oak for the top? Other than it's not as hard as
>> maple.
>> I have a bunch of 8/4 oak and want to make the top out of this wood, I
>> like oak as my favorite wood so that is why the question.....Brian
>>
>> --
>> www.members.cox.net/bsnikitas
>
> If you are the adventrous type, make the top up out of 1 1/2 strips of
> oak,
> glued up face to face. About 36 strips will give you a nice 28" top with
> the side grain showing. Looks nice and removes the splinter problem.
Hm. I have a ton of unfinished T&G 3/4" oak flooring cut-offs just looking
for a project. Think I might have one now... : )
Jason (married to a Deb himself)
<[email protected]> wrote in message
> My bench is built against 2 walls (L shape). It's a 2x4 base, 2 layers
> of 1" particle board overlayed with 3/4" oak T&G flooring. Works like
> a charm and looks like a champ.
It's nice when you're work bench is solid, stable and looks good as well.
On Wed, 13 Apr 2005 20:49:54 -0400, "Brian In Hampton"
<[email protected]> wrote:
>I am working (slowly) on a workbench and was wondering if there is a reason
>on not using oak for the top? Other than it's not as hard as maple.
>I have a bunch of 8/4 oak and want to make the top out of this wood, I like
>oak as my favorite wood so that is why the question.....Brian
The only reason I could think of is that it has open grain that will
feel a little rough to the touch, but other than that, I can't imagine
it would make anything less than a superb bench top.
Aut inveniam viam aut faciam
Short grain of maple, eh? I agree, a long grain such as red oak is painful
under the fingernails! Think about using one of the "wheat boards" as a
top, good stability and no finger nail splinters.
--
Rumpty
Radial Arm Saw Forum: http://forums.delphiforums.com/woodbutcher/start
- - - - - - - - - - - - - - - - - - - - -
"Leuf" <[email protected]> wrote in message
news:[email protected]...
> On Wed, 13 Apr 2005 20:49:54 -0400, "Brian In Hampton"
> <[email protected]> wrote:
>
> >I am working (slowly) on a workbench and was wondering if there is a
reason
> >on not using oak for the top? Other than it's not as hard as maple.
> >I have a bunch of 8/4 oak and want to make the top out of this wood, I
like
> >oak as my favorite wood so that is why the question.....Brian
>
> Lots of people use oak. The short grain of maple has its advantages,
> but any hardwood you can get cheap is good. Go for it.
>
>
> -Leuf