Carved Wooden Threads

Sonny wrote:
> And the mineral oil didn't soak in but about 5/8". You can see the penetration in the pics.... dark vs light wood. Probably needs to soak for a month, at least.
>
> Sonny
>
Maybe thin it with mineral spirits would speed it up. Or put under
pressure (as in a closed container under pressure).

--
G Ross

On Tuesday, February 25, 2020 at 4:19:52 PM UTC-5, Sonny wrote:
> Working on half the nut, carving the threads is not easy, nor very succes=
sful, yet. It took me 30 minutes to carve the one thread. This was too sl=
ow of going.
>=20
> First pic shows a pointed drill bit I used for gouging most of the waste.=
This bit's point was almost the valley profile needed.
> https://www.flickr.com/photos/43836144@N04/49585310742/in/dateposted-publ=
ic/
>=20
> Scroll left for two more pics relative to this next paragraph.
>=20
> It took 2.5 hours to carve the remainder of the threads. The screw aspe=
ct tracked well within the threads, but the threads were not nearly deep en=
ough. Today I deepened the threads (another 1.5 hours work) and still they=
are not deep enough. It will take a good bit more time to get this half n=
ut carved reasonably well.
>=20
> I'll finish this half and reluctantly carve the other half, but I think I=
'll stick to making wheel barrow handles. This thread carving is turning =
out to be quite a chore. I'll definitely further consult with the machinis=
t.
>=20
> Sonny

Truly a labor of love. Or stubbornness.

And the mineral oil didn't soak in but about 5/8". You can see the penetration in the pics.... dark vs light wood. Probably needs to soak for a month, at least.

Sonny

On Tue, 25 Feb 2020 19:18:15 -0500, G Ross <[email protected]> wrote:

>Sonny wrote:
>> And the mineral oil didn't soak in but about 5/8". You can see the penetration in the pics.... dark vs light wood. Probably needs to soak for a month, at least.
>>
>> Sonny
>>
>Maybe thin it with mineral spirits would speed it up. Or put under
>pressure (as in a closed container under pressure).

Maybe an old pressure cooker and some air fittings.

On Tuesday, February 25, 2020 at 7:18:23 PM UTC-5, G Ross wrote:
> Sonny wrote:
> > And the mineral oil didn't soak in but about 5/8". You can see the penetration in the pics.... dark vs light wood. Probably needs to soak for a month, at least.
> >
> > Sonny
> >
> Maybe thin it with mineral spirits would speed it up. Or put under
> pressure (as in a closed container under pressure).
>
> --
> G Ross

Maybe use one of these?

https://images-na.ssl-images-amazon.com/images/I/51T6JKFpuvL.jpg

I completely disavow that recommendation and state that any use of said
suggestion (which I didn't post) legally triggers the hold harmless clause
of this agreement, a clause which will remain in full effect ad infinitum.

On Tuesday, February 25, 2020 at 6:18:23 PM UTC-6, G Ross wrote:

> Maybe thin it with mineral spirits would speed it up.

Or maybe better yet, soak it in mineral spirits only. When working it, keep the surface moist with thinned mineral oil.

Sonny

On Tuesday, February 25, 2020 at 7:10:14 PM UTC-6, DerbyDad03 wrote:

> Truly a labor of love. Or stubbornness.

A little of both. I liked the caring. My biggest problem was standing fo=
r long periods. My legs and back can't handle the subsequent/eventual slou=
ching posture.

I like to finish what I start, so I won't give up just yet. My aim is to f=
ix that second work table.

Another issue: I made eight 1" square bench dogs for the table that is rep=
aired, proud of the results. Alas, the dog holes aren't symmetrically cut =
and my dogs don't fit into all the holes. They were hand cut, but a poor j=
ob. I've started to trim them more neatly square, better fitting my dogs. =
I suppose the original cutter was an apprentice in training and/or didn't =
have a decent (paring?) chisel.

Sonny