I have a 7-foot long work table that currently has an (now old) plywood top
and folding metal legs attached to it. I want to use this for electronics
work and the aged plywood surface is just too coarse for trying to locate
small parts dropped onto it.
What do you recommend? Put some kind of plastic laminate on top of this or
replace the entire top -- ie, pull off the folding legs and attach them to
another material? :: laminate MDF or such?
Thanks.
> If it's rigid-enough to satisfy as is and the surface is basically
> sound; sure, laminate is a relatively inexpensive option. Will need
> enough surface-prep work to eliminate any really large (like inches)
> gaps, etc., and knock off any high spots w/ belt sander or equivalent
> and go for it. I'd do it basically like a counter-top; laminate a
> second layer around the edge for the thickness/appearance and either
> laminate it as well or use a solid banding.
> [dpb]
What adhesive would you recommend to stick a melamine laminate to the plywood
top?
Naming brand names is always good... (c; (I'm in the USA)
Thanks.
On Mar 23, 6:11=A0pm, Mike Cook <[email protected]> wrote:
> I have a 7-foot long work table that currently has an (now old) plywood t=
op
> and folding metal legs attached to it. I want to use this for electronics
> work and the aged plywood surface is just too coarse for trying to locate
> small parts dropped onto it.
>
> What do you recommend? Put some kind of plastic laminate on top of this o=
r
> replace the entire top -- ie, pull off the folding legs and attach them t=
o
> another material? :: laminate MDF or such?
>
> Thanks.
For a light duty table, replace the top with a hollow core door.
On 3/26/2012 10:05 AM, Pat Barber wrote:
> On 3/23/2012 3:11 PM, Mike Cook wrote:
>> I have a 7-foot long work table that currently has an (now old)
>> plywood top
>> and folding metal legs attached to it. I want to use this for electronics
>> work and the aged plywood surface is just too coarse for trying to locate
>> small parts dropped onto it.
>>
> Replace the plywood with a 4x8(or whatever size) sheet of melamine.
>
> The melamine is very tough and very white which is better for finding
> small parts on.
>
> Put some snazzy wood edging on it and you will have a nice looking
> work table.
And were I to redo a top for the purpose of an electronics work table,
not only would I welcome the tough melamine surface, I'd trim the whole
top with a nice hardwood band (maple or oak) and leave a small lip ( ~
1/8" - 3/16") around the top to prevent those small parts from rolling
off the table and onto the floor where you REALLY have fun finding them <g>
On 3/23/2012 5:11 PM, Mike Cook wrote:
> I have a 7-foot long work table that currently has an (now old) plywood top
> and folding metal legs attached to it. I want to use this for electronics
> work and the aged plywood surface is just too coarse for trying to locate
> small parts dropped onto it.
>
> What do you recommend? Put some kind of plastic laminate on top of this or
> replace the entire top -- ie, pull off the folding legs and attach them to
> another material? :: laminate MDF or such?
>
> Thanks.
>
If the present top is sturdy enough for your needs and you only object
to the finish of the top, I would cap with a piece of tempered masonite
that is trapped by an edge band so it was easy to turn over and/or change.
If a new sturdy top is in order, consider a damaged solid core door.
Everyone who handles doors ends up with some damaged, but you need to
ask or find a demolition site and ask, they are usually thrown away.
--
___________________________________
Keep the whole world singing . . .
Dan G
remove the seven
On 3/23/2012 5:11 PM, Mike Cook wrote:
> I have a 7-foot long work table that currently has an (now old) plywood top
> and folding metal legs attached to it. I want to use this for electronics
> work and the aged plywood surface is just too coarse for trying to locate
> small parts dropped onto it.
>
> What do you recommend? Put some kind of plastic laminate on top of this or
> replace the entire top -- ie, pull off the folding legs and attach them to
> another material? :: laminate MDF or such?
If it's rigid-enough to satisfy as is and the surface is basically
sound; sure, laminate is a relatively inexpensive option. Will need
enough surface-prep work to eliminate any really large (like inches)
gaps, etc., and knock off any high spots w/ belt sander or equivalent
and go for it. I'd do it basically like a counter-top; laminate a
second layer around the edge for the thickness/appearance and either
laminate it as well or use a solid banding.
Remember to use a reasonably light (as in color) surface; it's much
easier to find stuff on.
I did the above except built solid legs when switched from consulting
through a firm to independent and found a piece of cheap laminate of
sufficient size at a building salvage/seconds outlet. Depending on how
large you want, it's also possible to find leftovers from kitchen
cabinet redo's, etc., that are as cheap or cheaper than just the laminate.
--
On 3/23/2012 6:34 PM, dpb wrote:
> On 3/23/2012 5:11 PM, Mike Cook wrote:
>> I have a 7-foot long work table that currently has an (now old)
>> plywood top
>> and folding metal legs attached to it. I want to use this for electronics
>> work and the aged plywood surface is just too coarse for trying to locate
>> small parts dropped onto it.
>>
>> What do you recommend? Put some kind of plastic laminate on top of
>> this or
>> replace the entire top -- ie, pull off the folding legs and attach
>> them to
>> another material? :: laminate MDF or such?
>
> If it's rigid-enough to satisfy as is and the surface is basically
> sound; sure, laminate is a relatively inexpensive option. Will need
> enough surface-prep work to eliminate any really large (like inches)
> gaps, etc., and knock off any high spots w/ belt sander or equivalent
> and go for it. I'd do it basically like a counter-top; laminate a second
> layer around the edge for the thickness/appearance and either laminate
> it as well or use a solid banding.
>
> Remember to use a reasonably light (as in color) surface; it's much
> easier to find stuff on.
>
> I did the above except built solid legs when switched from consulting
> through a firm to independent and found a piece of cheap laminate of
> sufficient size at a building salvage/seconds outlet. Depending on how
> large you want, it's also possible to find leftovers from kitchen
> cabinet redo's, etc., that are as cheap or cheaper than just the laminate.
>
> --
>
In our area there is a Habitat for Humanity outlet store. Habitatâs
ReStore resale outlets sell reusable and surplus building materials to
the public.
They may have what you are looking for.
"Mike Cook" <[email protected]> wrote in message
news:[email protected]...
>I have a 7-foot long work table that currently has an (now old) plywood top
> and folding metal legs attached to it. I want to use this for electronics
> work and the aged plywood surface is just too coarse for trying to locate
> small parts dropped onto it.
>
> What do you recommend? Put some kind of plastic laminate on top of this or
> replace the entire top -- ie, pull off the folding legs and attach them to
> another material? :: laminate MDF or such?
>
> Thanks.
These requests are so difficult because of each individual's needs. In some
cases, an exterior door is just fine. In others, something with ninety
degree fences or jigs, or flat plane surfaces is the way to go.
I would identify your needs, then go from there.
A GOOD! (and I emphasize that point on purpose) is worth its weight in gold,
but what is just perfect to one may be worthless, or at least, inadequate
for another.
Identify your needs, then design from there.
I currently have just put up four doors as work tables. One, because they
were free, and two, I have every intention of them teaching me what I need
exactly, so I do expect to morph into further mods.
There is no "right", nor "perfect". If I had enough space, I would have
probably six tables, each for specific purposes.
HTH
Steve
"Keith Nuttle" <[email protected]> wrote in message
news:[email protected]...
> On 3/23/2012 6:34 PM, dpb wrote:
>> On 3/23/2012 5:11 PM, Mike Cook wrote:
>>> I have a 7-foot long work table that currently has an (now old)
>>> plywood top
>>> and folding metal legs attached to it. I want to use this for
>>> electronics
>>> work and the aged plywood surface is just too coarse for trying to
>>> locate
>>> small parts dropped onto it.
>>>
>>> What do you recommend? Put some kind of plastic laminate on top of
>>> this or
>>> replace the entire top -- ie, pull off the folding legs and attach
>>> them to
>>> another material? :: laminate MDF or such?
>>
>> If it's rigid-enough to satisfy as is and the surface is basically
>> sound; sure, laminate is a relatively inexpensive option. Will need
>> enough surface-prep work to eliminate any really large (like inches)
>> gaps, etc., and knock off any high spots w/ belt sander or equivalent
>> and go for it. I'd do it basically like a counter-top; laminate a second
>> layer around the edge for the thickness/appearance and either laminate
>> it as well or use a solid banding.
>>
>> Remember to use a reasonably light (as in color) surface; it's much
>> easier to find stuff on.
>>
>> I did the above except built solid legs when switched from consulting
>> through a firm to independent and found a piece of cheap laminate of
>> sufficient size at a building salvage/seconds outlet. Depending on how
>> large you want, it's also possible to find leftovers from kitchen
>> cabinet redo's, etc., that are as cheap or cheaper than just the
>> laminate.
>>
>> --
>>
> In our area there is a Habitat for Humanity outlet store. Habitat's
> ReStore resale outlets sell reusable and surplus building materials to the
> public.
>
> They may have what you are looking for.
ReStore has some awesome things, particularly that one piece of a puzzle
that you could never identify, let alone find. I am building a wind wall
for my barbecue area out of double sets of dual pane glass doors. I have
about four more sets until I get enough, then I'll get to the good part
............... making the metal frame to hold them all.
I love ReStore, and like to just go browse, never knowing what the discards
du jour may be.
Steve
>
Mike Cook wrote:
> I have a 7-foot long work table that currently has an (now old)
> plywood top and folding metal legs attached to it. I want to use this
> for electronics work and the aged plywood surface is just too coarse
> for trying to locate small parts dropped onto it.
>
> What do you recommend? Put some kind of plastic laminate on top of
> this or replace the entire top -- ie, pull off the folding legs and
> attach them to another material? :: laminate MDF or such?
>
> Thanks.
I'd go get a sheet of melamine board and some 2x4s. Make frame & legs with
2x4s' cut mel board to size for top....smooth, hard, durable. And cheaper
than a sheet of laminate.
If you just have to have folding legs, use what you have but make an apron
all around the mel board - and a couple of pieces crosswise - to support it
and attach the legs to that.
--
dadiOH
____________________________
dadiOH's dandies v3.06...
...a help file of info about MP3s, recording from
LP/cassette and tips & tricks on this and that.
Get it at http://mysite.verizon.net/xico
On 3/23/2012 3:11 PM, Mike Cook wrote:
> I have a 7-foot long work table that currently has an (now old) plywood top
> and folding metal legs attached to it. I want to use this for electronics
> work and the aged plywood surface is just too coarse for trying to locate
> small parts dropped onto it.
>
> What do you recommend? Put some kind of plastic laminate on top of this or
> replace the entire top -- ie, pull off the folding legs and attach them to
> another material? :: laminate MDF or such?
>
> Thanks.
>
Replace the plywood with a 4x8(or whatever size) sheet of melamine.
The melamine is very tough and very white which is better for finding
small parts on.
Put some snazzy wood edging on it and you will have a nice looking
work table.
Cheap,tough and quick.
On Fri, 23 Mar 2012 15:11:24 -0700, Mike Cook <[email protected]>
wrote:
>I have a 7-foot long work table that currently has an (now old) plywood top
>and folding metal legs attached to it. I want to use this for electronics
>work and the aged plywood surface is just too coarse for trying to locate
>small parts dropped onto it.
>
>What do you recommend? Put some kind of plastic laminate on top of this or
>replace the entire top -- ie, pull off the folding legs and attach them to
>another material? :: laminate MDF or such?
>
>Thanks.
Laminate makes a nice smooth and easy to clean surface. You may get
lucky and score some cheap if you have a kitchen installer nearby. Ask
if they have any leftovers or cancellations they will sell cheap.
On 3/29/2012 6:00 PM, Mike Cook wrote:
>> If it's rigid-enough to satisfy as is and the surface is basically
>> sound; sure, laminate is a relatively inexpensive option. Will need
>> enough surface-prep work to eliminate any really large (like inches)
>> gaps, etc., and knock off any high spots w/ belt sander or equivalent
>> and go for it. I'd do it basically like a counter-top; laminate a
>> second layer around the edge for the thickness/appearance and either
>> laminate it as well or use a solid banding.
>> [dpb]
>
> What adhesive would you recommend to stick a melamine laminate to the plywood
> top?
>
> Naming brand names is always good... (c; (I'm in the USA)
>
> Thanks.
>
Once again?
G-Flex epoxy