Table saw splitter

Mike,

Be careful with this saw. I had a Delta 36-600 and I loved it. Great
saw to get started but it had some limitations, which can be overcome
with some jigs and some patience. I believe this saw is the same as
what is now your model. Correct me if I'm wrong, the the spitter hand
from a support that is connected to a rod coming out of the back of the
saw and there is no support through the throat plate. Is that correct?

If so, be very careful with that blade guard. The splitters on most
saws have that additional support through the throat plate, but the
lack of that additional support makes this very flimsy. When cross
cutting some wood, my splitter deflected and was actually caught by the
blade. I quickly turned the saw off, and no wood flew any where, but
it scared me. I started using the saw without the guard.

I made a homemade zero clearance throat plate out of some extra 1/8th
inch panaling. You can glue some sort of a homemde splitter to that.
Unfortunately, none of the after market splitters will work.

Good luck with the saw. I've since moved on, but I made a basement
full of cabinets with that saw and in the process got hooked on this
woodworking. If you DAWGS on my handle Woodchuck34 + 36-600, you'll
see a lot of old info on my experiences with the saw. I just double
checked Delta's website and it does appear to be the smae saw.

Chuck

You might be able to guess why I was asking. The rod that the splitter
connects to extends several inches beyond the back of the table and in
a one-car garage I was looking to push the TS further against the wall
when not in use. Taking the splitter off still leaves the rod sticking
out. So I was thinking about shortening the rod and rethreading it.
This alone would push the splitter closer to the blade so I'd also have
to modify the splitter too.

I'll post a picture to the woodworking binaries group; it'll be
obvious.

Mike

Can't buy a Micro Jig for that model of TS as the throat plate is too
thin (1/4" thick). I know because I used to own that model and the you
can't get the micro jig to work. I do use it now and love it.

Chuck

[email protected] wrote:
> Anyway, my question is about the splitter. At the back, where it
> mounts to the rod...it's a considerable distance away from the table.
> Is there a reason for this?

If you consider what the splitter does, you'll see it doesn't need
to be close to the blade. It's stopping wood that would have warped
the cut closed from doing that, so it can't bind on the rising part
of the blade and get tossed out.

<[email protected]> wrote in message
news:[email protected]...
>I just got a Delta TS350. I like it so far. I wish I could have fit a
> larger contractor saw, but my space is limited and this should keep me
> busy for a while. Even before I build the drawers for my workbench I
> think I'll build a crosscut sled and a tenon jig this weekend.
>
> Anyway, my question is about the splitter. At the back, where it
> mounts to the rod...it's a considerable distance away from the table.
> Is there a reason for this? I checked out the manuals for other Delta
> table saws and they look similar. Is there any reason why it couldn't
> have been moved to within 1/4" or so of the table?
>
> Mike
>

If you move it closer it may come in contact with the blade as you raise the
blade higher.

"Clifford Heath" <[email protected]> wrote in message
news:[email protected]...
>
> If you consider what the splitter does, you'll see it doesn't need
> to be close to the blade. It's stopping wood that would have warped
> the cut closed from doing that, so it can't bind on the rising part
> of the blade and get tossed out.

Well the closer the better. I have had wood start to close up on me before
reaching the splitter and that was after cutting several pieces from the
same board with no problems.

[email protected] writes:

> You might be able to guess why I was asking. The rod that the splitter
> connects to extends several inches beyond the back of the table and in
> a one-car garage I was looking to push the TS further against the wall
> when not in use. Taking the splitter off still leaves the rod sticking
> out. So I was thinking about shortening the rod and rethreading it.
> This alone would push the splitter closer to the blade so I'd also have
> to modify the splitter too.


You can buy a Micro-Jig splitter for under $25.

http://www.microjig.com/MJ%20Splitter.htm


--
Sending unsolicited commercial e-mail to this account incurs a fee of
$500 per message, and acknowledges the legality of this contract.

<[email protected]> wrote in message
news:[email protected]...
>I just got a Delta TS350. I like it so far. I wish I could have fit a
> larger contractor saw, but my space is limited and this should keep me
> busy for a while. Even before I build the drawers for my workbench I
> think I'll build a crosscut sled and a tenon jig this weekend.
>
> Anyway, my question is about the splitter. At the back, where it
> mounts to the rod...it's a considerable distance away from the table.
> Is there a reason for this? I checked out the manuals for other Delta
> table saws and they look similar. Is there any reason why it couldn't
> have been moved to within 1/4" or so of the table?
>
It is raised above the table? That can't be right, it won't work for thin
wood. I must be misunderstanding you.
All I can think is that it is a distance to accomodate angling the blade;
but that would be a lousy design.