Hello experienced woodworkers :)
I am working on a special project (I'm actually a textile artist), and I
need to have some masonite or hardboard cut into a specific size and shape
(small squares) in some quantity.
I will have to shop this out to someone, and I need to have as ultra smooth
edges as I can get with exact size. Is what I'm looking for called laser
cutting or dye cutting, and what is the difference?
Where would I look to find someone like this to do this type of work?
Thanks for any kind help :)
L&D
In article <[email protected]>, L&D
<[email protected]> wrote:
> Hello experienced woodworkers :)
>
> I am working on a special project (I'm actually a textile artist), and I
> need to have some masonite or hardboard cut into a specific size and shape
> (small squares) in some quantity.
>
> I will have to shop this out to someone, and I need to have as ultra smooth
> edges as I can get with exact size. Is what I'm looking for called laser
> cutting or dye cutting, and what is the difference?
>
> Where would I look to find someone like this to do this type of work?
>
> Thanks for any kind help :)
>
> L&D
Not quite an answer to your question, but any woodworker with a good
table saw and top-notch blade, a Forrest WWII, for example, could
probably do the job for less expense than either of your alternatives,
depending on the size of the squares, of course.
I'd guess about than an hour to cut several hundred squares of any size
from 1" to, say 4" if you brought the hardboard. And the edges would
be smooth as silk.
'course, everything takes more time and costs more than the estimate.
:-)
--
Vince Heuring ECE Department, University of Colorado - Boulder
To email, remove the Vince.
Thanks, I will check out his website--it looks like I don't really require
die-cutting which is good news!
L&D
"Bill Price" <[email protected]> wrote in message
news:[email protected]...
> Talk to David Donoho at http:\\www.teccut.com He is laser-cutting complex
> parts for me in 1/16" x 4 x 24 sheets of basswood for about $4 a sheet.
The
> kerf is .007", my biggest part is 16" long and comes out within .002" of
> design. I did my own CAD drawing so there was no setup charge. He can
> recommend a material for your project.
>
> Die cutting has problems with sharp corners, slight wavy lines, and a
> whopping charge to build the die. Production is much less expensive.
>
> Sawing them on a table saw is easy, sawing them accurately requires skill
> and patience.
>
> "L&D" <[email protected]> wrote in message
> news:[email protected]...
> > Hello experienced woodworkers :)
> >
> > I am working on a special project (I'm actually a textile artist), and I
> > need to have some masonite or hardboard cut into a specific size and
shape
> > (small squares) in some quantity.
> >
> > I will have to shop this out to someone, and I need to have as ultra
> smooth
> > edges as I can get with exact size. Is what I'm looking for called
laser
> > cutting or dye cutting, and what is the difference?
> >
> > Where would I look to find someone like this to do this type of work?
> >
> > Thanks for any kind help :)
> >
> > L&D
> >
> >
>
>
>
Talk to David Donoho at http:\\www.teccut.com He is laser-cutting complex
parts for me in 1/16" x 4 x 24 sheets of basswood for about $4 a sheet. The
kerf is .007", my biggest part is 16" long and comes out within .002" of
design. I did my own CAD drawing so there was no setup charge. He can
recommend a material for your project.
Die cutting has problems with sharp corners, slight wavy lines, and a
whopping charge to build the die. Production is much less expensive.
Sawing them on a table saw is easy, sawing them accurately requires skill
and patience.
"L&D" <[email protected]> wrote in message
news:[email protected]...
> Hello experienced woodworkers :)
>
> I am working on a special project (I'm actually a textile artist), and I
> need to have some masonite or hardboard cut into a specific size and shape
> (small squares) in some quantity.
>
> I will have to shop this out to someone, and I need to have as ultra
smooth
> edges as I can get with exact size. Is what I'm looking for called laser
> cutting or dye cutting, and what is the difference?
>
> Where would I look to find someone like this to do this type of work?
>
> Thanks for any kind help :)
>
> L&D
>
>
Sounds to me like a guy with a table saw would be a better bet than either.
When you say "exact size", bear in mind that there is no such thing as
exact.
"L&D" <[email protected]> wrote in message
news:[email protected]...
> Hello experienced woodworkers :)
>
> I am working on a special project (I'm actually a textile artist), and I
> need to have some masonite or hardboard cut into a specific size and shape
> (small squares) in some quantity.
>
> I will have to shop this out to someone, and I need to have as ultra
smooth
> edges as I can get with exact size. Is what I'm looking for called laser
> cutting or dye cutting, and what is the difference?
>
> Where would I look to find someone like this to do this type of work?
>
> Thanks for any kind help :)
>
> L&D
>
>
Thanks for responding, this sounds exactly what I am look for, and if it can
be done with traditional methods I'm all for it :).
Specifically I am looking for 4"x4" squares, uniformity being very important
. I am trying to decide between 2 different types of board as described
here:
One type is described as follows:
>>>
16 x 20" Painting panels made from special (approximately 5/32" thick)
compressed
wood and covered with an even textured canvas that has an acid-free, all
media priming. >>>>>
The second type is described:
"Canvas Mounted Hardboard Panel": Crafted on a 3.2 mm thick, non-direction
composite hardboard (similar to masonite). The 100% cotton, acid-free all
media primed cotton canvas surface Size 20x24" panel.
I would probably need 100-150 initially, with the ability to re-order
(unsure yet of the duration between orders yet>)
Is this do-able as you describe?
Thanks for your input :)
L&D
"Vince Heuring" <[email protected]> wrote in message
news:100820031404430454%[email protected]...
> In article <[email protected]>, L&D
> <[email protected]> wrote:
>
> > Hello experienced woodworkers :)
> >
> > I am working on a special project (I'm actually a textile artist), and I
> > need to have some masonite or hardboard cut into a specific size and
shape
> > (small squares) in some quantity.
> >
> > I will have to shop this out to someone, and I need to have as ultra
smooth
> > edges as I can get with exact size. Is what I'm looking for called
laser
> > cutting or dye cutting, and what is the difference?
> >
> > Where would I look to find someone like this to do this type of work?
> >
> > Thanks for any kind help :)
> >
> > L&D
>
> Not quite an answer to your question, but any woodworker with a good
> table saw and top-notch blade, a Forrest WWII, for example, could
> probably do the job for less expense than either of your alternatives,
> depending on the size of the squares, of course.
>
> I'd guess about than an hour to cut several hundred squares of any size
> from 1" to, say 4" if you brought the hardboard. And the edges would
> be smooth as silk.
>
> 'course, everything takes more time and costs more than the estimate.
> :-)
>
> --
> Vince Heuring ECE Department, University of Colorado - Boulder
> To email, remove the Vince.
I would try GlobalSpec
http://www.globalspec.com/
You can search for waterjet cutting services by capabilities and location.
You can find suppliers and discuss your needs one to one
"L&D" <[email protected]> wrote in message news:<[email protected]>...
> Thanks to everyone for your kind and fast responses--I will continue doing
> research using all of your suggestions :)
>
> L&D
> "Carl Olsen" <[email protected]> wrote in message
> news:[email protected]...
> > I agree with some of the others that a saw is likely the way to go for
> > this particular project (though it might not be). In the event that
> > you are looking for water jet or laser cutting job shops to do the
> > work for you, you can look a the following directories:
> >
> > Look here for waterjet shops in the USA (And many of them have lasers
> > and other equipment):
> >
> > http://www.waterjets.org/waterjet_jobshops.html
> >
> > Look here for waterjet shops around the world (Again, with many of
> > them having other equipment also):
> >
> > http://www.waterjets.org/international_waterjet_jobshops.html
> >
> > To learn more about waterjets in general, visit:
> >
> > http://www.waterjets.org
> >
> > - Carl
> > Web Master
> > Waterjet Web Reference (the above mentioned site).
> >
> > [email protected] (Phil) wrote in message
> news:<[email protected]>...
> > > "L&D" <[email protected]> wrote in message
> news:<[email protected]>...
> > > > Hello experienced woodworkers :)
> > > >
> > > > I am working on a special project (I'm actually a textile artist), and
> I
> > > > need to have some masonite or hardboard cut into a specific size and
> shape
> > > > (small squares) in some quantity.
> > > >
> > > > I will have to shop this out to someone, and I need to have as ultra
> smooth
> > > > edges as I can get with exact size. Is what I'm looking for called
> laser
> > > > cutting or dye cutting, and what is the difference?
> > > >
> > > > Where would I look to find someone like this to do this type of work?
> > > >
> > > > Thanks for any kind help :)
> > > >
> > > > L&D
> > >
> > > Hi,
> > > Look online for waterjet or laser cutting. Both of these processes
> > > can usually deliver +/-.005 to .010 inch tolerances, tighter if you
> > > ask for it and don't mind paying a little extra.
> > >
> > > I've used both for metal, plastic and glass and it works great. I've
> > > read that it works well on wood as well, the waterjet uses very little
> > > water and if you mask the surfaces you shouldn't experiences any
> > > problems. The lasers will burn the materail slightly but it is easy to
> > > sand off.
> > >
> > > Do a search for waterjet cutting, laser cutting in the Google.com
> > > directory listings or you can also find many listings in the
> > > Thomas Register, go here: http://www.thomasregister.com/
> > >
> > > Good Luck,
> > >
> > > Phil
Thanks Greybeard, do you know if 1/8" or 1/25" thick hardboard/masonite be
too much for a dye cut? Would this give me a smoother cut than laser?
I appreciate your comments :)
L&D
"Greybeard" <[email protected]> wrote in message
news:[email protected]...
> Also-there will be some charring on the edges from the burning process-die
> cutting has limits to material thickness-usually thinner stuff like
> cardboards, etc.
>
>
"L&D" <[email protected]> wrote in message news:<[email protected]>...
> Hello experienced woodworkers :)
>
> I am working on a special project (I'm actually a textile artist), and I
> need to have some masonite or hardboard cut into a specific size and shape
> (small squares) in some quantity.
>
> I will have to shop this out to someone, and I need to have as ultra smooth
> edges as I can get with exact size. Is what I'm looking for called laser
> cutting or dye cutting, and what is the difference?
>
> Where would I look to find someone like this to do this type of work?
>
> Thanks for any kind help :)
>
> L&D
Hi,
Look online for waterjet or laser cutting. Both of these processes
can usually deliver +/-.005 to .010 inch tolerances, tighter if you
ask for it and don't mind paying a little extra.
I've used both for metal, plastic and glass and it works great. I've
read that it works well on wood as well, the waterjet uses very little
water and if you mask the surfaces you shouldn't experiences any
problems. The lasers will burn the materail slightly but it is easy to
sand off.
Do a search for waterjet cutting, laser cutting in the Google.com
directory listings or you can also find many listings in the
Thomas Register, go here: http://www.thomasregister.com/
Good Luck,
Phil
I agree with some of the others that a saw is likely the way to go for
this particular project (though it might not be). In the event that
you are looking for water jet or laser cutting job shops to do the
work for you, you can look a the following directories:
Look here for waterjet shops in the USA (And many of them have lasers
and other equipment):
http://www.waterjets.org/waterjet_jobshops.html
Look here for waterjet shops around the world (Again, with many of
them having other equipment also):
http://www.waterjets.org/international_waterjet_jobshops.html
To learn more about waterjets in general, visit:
http://www.waterjets.org
- Carl
Web Master
Waterjet Web Reference (the above mentioned site).
[email protected] (Phil) wrote in message news:<[email protected]>...
> "L&D" <[email protected]> wrote in message news:<[email protected]>...
> > Hello experienced woodworkers :)
> >
> > I am working on a special project (I'm actually a textile artist), and I
> > need to have some masonite or hardboard cut into a specific size and shape
> > (small squares) in some quantity.
> >
> > I will have to shop this out to someone, and I need to have as ultra smooth
> > edges as I can get with exact size. Is what I'm looking for called laser
> > cutting or dye cutting, and what is the difference?
> >
> > Where would I look to find someone like this to do this type of work?
> >
> > Thanks for any kind help :)
> >
> > L&D
>
> Hi,
> Look online for waterjet or laser cutting. Both of these processes
> can usually deliver +/-.005 to .010 inch tolerances, tighter if you
> ask for it and don't mind paying a little extra.
>
> I've used both for metal, plastic and glass and it works great. I've
> read that it works well on wood as well, the waterjet uses very little
> water and if you mask the surfaces you shouldn't experiences any
> problems. The lasers will burn the materail slightly but it is easy to
> sand off.
>
> Do a search for waterjet cutting, laser cutting in the Google.com
> directory listings or you can also find many listings in the
> Thomas Register, go here: http://www.thomasregister.com/
>
> Good Luck,
>
> Phil
Thanks to everyone for your kind and fast responses--I will continue doing
research using all of your suggestions :)
L&D
"Carl Olsen" <[email protected]> wrote in message
news:[email protected]...
> I agree with some of the others that a saw is likely the way to go for
> this particular project (though it might not be). In the event that
> you are looking for water jet or laser cutting job shops to do the
> work for you, you can look a the following directories:
>
> Look here for waterjet shops in the USA (And many of them have lasers
> and other equipment):
>
> http://www.waterjets.org/waterjet_jobshops.html
>
> Look here for waterjet shops around the world (Again, with many of
> them having other equipment also):
>
> http://www.waterjets.org/international_waterjet_jobshops.html
>
> To learn more about waterjets in general, visit:
>
> http://www.waterjets.org
>
> - Carl
> Web Master
> Waterjet Web Reference (the above mentioned site).
>
> [email protected] (Phil) wrote in message
news:<[email protected]>...
> > "L&D" <[email protected]> wrote in message
news:<[email protected]>...
> > > Hello experienced woodworkers :)
> > >
> > > I am working on a special project (I'm actually a textile artist), and
I
> > > need to have some masonite or hardboard cut into a specific size and
shape
> > > (small squares) in some quantity.
> > >
> > > I will have to shop this out to someone, and I need to have as ultra
smooth
> > > edges as I can get with exact size. Is what I'm looking for called
laser
> > > cutting or dye cutting, and what is the difference?
> > >
> > > Where would I look to find someone like this to do this type of work?
> > >
> > > Thanks for any kind help :)
> > >
> > > L&D
> >
> > Hi,
> > Look online for waterjet or laser cutting. Both of these processes
> > can usually deliver +/-.005 to .010 inch tolerances, tighter if you
> > ask for it and don't mind paying a little extra.
> >
> > I've used both for metal, plastic and glass and it works great. I've
> > read that it works well on wood as well, the waterjet uses very little
> > water and if you mask the surfaces you shouldn't experiences any
> > problems. The lasers will burn the materail slightly but it is easy to
> > sand off.
> >
> > Do a search for waterjet cutting, laser cutting in the Google.com
> > directory listings or you can also find many listings in the
> > Thomas Register, go here: http://www.thomasregister.com/
> >
> > Good Luck,
> >
> > Phil
"L&D" <[email protected]> wrote:
>Hello experienced woodworkers :)
>
>I am working on a special project (I'm actually a textile artist), and I
>need to have some masonite or hardboard cut into a specific size and shape
>(small squares) in some quantity.
What quantity, it makes a big difference. Give dimensions.
>
>I will have to shop this out to someone, and I need to have as ultra smooth
>edges as I can get with exact size. Is what I'm looking for called laser
>cutting or dye cutting, and what is the difference?
Laser burns material and has cutting beam guided by some sort of
motion control system. Die Cutting uses steel blades embeded in die
board (really great plywood) that is forced into material by a full
revolution press or a hyd press against a steel score plate.
>
>Where would I look to find someone like this to do this type of work?
Where do you live? There is a laser shop in GR Michigan iirc and I
know that there is a die cutter in Traverse City Mi. A web search
should find someone close to you.
>
>
Wes
--
Reply to:
Whiskey Echo Sierra Sierra AT Gee Tee EYE EYE dot COM
Lycos address is a spam trap.