"philly45" <[email protected]> wrote in message
news:[email protected]...
> What size dado should be used with a 1.5 HP (120V) Delta Profession Table
> Saw? Is the power adequate for an 8" dado set or should a 6" set be used?
> Does anyone have experience using an 8" dado set with a 1.5 HP Contractor
> saw? What are the CONS of such a setup?
>
>
I use a 8" on my Delta contractors saw, no problems.
Greg
"philly45" <[email protected]> wrote in message
> What size dado should be used with a 1.5 HP (120V) Delta Profession Table
> Saw? Is the power adequate for an 8" dado set or should a 6" set be used?
> Does anyone have experience using an 8" dado set with a 1.5 HP Contractor
> saw? What are the CONS of such a setup?
>
>
When I bought my dado at a show, the owner of the company, Ridge Carbide
Tool, told me to get the 8". He said the 6" is for the smaller benchtop
type saws and any 1 1/2 HP can handle the 8". I've used mine for oak
plywood, MDF and solid wood with no problem.
You do have to slow the feed rate for deep cuts if you are taking a wide
cut. Removing 3/4" of material takes a bit more than a normal blade kerf.
Been using a Freud SD508 set on a Jet contractor's 1 and 1/2 hp for
about ten years. Don't see any downside
bob g.
philly45 wrote:
> What size dado should be used with a 1.5 HP (120V) Delta Profession Table
> Saw? Is the power adequate for an 8" dado set or should a 6" set be used?
> Does anyone have experience using an 8" dado set with a 1.5 HP Contractor
> saw? What are the CONS of such a setup?
>
>
philly45 wrote:
> What size dado should be used with a 1.5 HP (120V) Delta Profession Table
> Saw? Is the power adequate for an 8" dado set or should a 6" set be used?
> Does anyone have experience using an 8" dado set with a 1.5 HP Contractor
> saw? What are the CONS of such a setup?
Can't speak directly for the Delta but an 8" works fine on my 1.5 HP
Craftsman RAS on everything I've tried it on--haven't set it for max width
and gone after a piece of Ipe yet but even there the worst that's likely is
that it would be necessary to make multiple passes.
The only real con I see is cost.
--
--John
Reply to jclarke at ae tee tee global dot net
(was jclarke at eye bee em dot net)
On Sat, 04 Sep 2004 02:26:50 GMT, "philly45"
<[email protected]> wrote:
>What size dado should be used with a 1.5 HP (120V) Delta Profession Table
>Saw? Is the power adequate for an 8" dado set or should a 6" set be used?
>Does anyone have experience using an 8" dado set with a 1.5 HP Contractor
>saw? What are the CONS of such a setup?
>
I'd use the 8" dado set. I can't think of any considerable "CON",
other than perhaps cost. A 8" will run smoother and should provide a
cleaner cut.
In article <[email protected]>,
"Edwin Pawlowski" <[email protected]> wrote:
> "philly45" <[email protected]> wrote in message
>
> > What size dado should be used with a 1.5 HP (120V) Delta Profession Table
> > Saw? Is the power adequate for an 8" dado set or should a 6" set be used?
> > Does anyone have experience using an 8" dado set with a 1.5 HP Contractor
> > saw? What are the CONS of such a setup?
> >
> >
>
> When I bought my dado at a show, the owner of the company, Ridge Carbide
> Tool, told me to get the 8". He said the 6" is for the smaller benchtop
> type saws and any 1 1/2 HP can handle the 8". I've used mine for oak
> plywood, MDF and solid wood with no problem.
>
> You do have to slow the feed rate for deep cuts if you are taking a wide
> cut. Removing 3/4" of material takes a bit more than a normal blade kerf.
My first saw was a BT-3000. I got a 6" dado blade for it because there
wasn't clearance inside the dust collection shroud for an 8" one (yes, I
know some people say it can be done).
I had never actually run into anything I couldn't do with the 6" dado
blade, but when I upgraded to a unisaw, I went out and bought an 8" set
anyway. Funny thing is that now I more often than not just use the 6"
set, and the 8" one sits on the shelf. I find the smaller blades easier
to maneuver on and off the arbor without banging the teeth into metal
stuff.
On Sat, 04 Sep 2004 10:09:10 -0400, Roy Smith <[email protected]> wrote:
>I had never actually run into anything I couldn't do with the 6" dado
>blade,
Do you ever use a crosscut sled to dado?
Barry