I have a Ridgid hand-held router that I've been using with 1/2" bits. More
than once, the collet has stuck and held the bit in place AFTER the nut has
been loosened and removed.
My research shows a few solutions such as parafin wax, graphite, or just
making sure the collet and recieving end are clean. Has anyone tried these
solutions, and do they work?
I'll try cleaning the collet and recieving end next time I use the router.
Puckdropper
--
Wise is the man who attempts to answer his question before asking it.
To email me directly, send a message to puckdropper (at) fastmail.fm
"Puckdropper" wrote:
>I have a Ridgid hand-held router that I've been using with 1/2" bits. More
> than once, the collet has stuck and held the bit in place AFTER the nut
> has
> been loosened and removed.
>
> My research shows a few solutions such as parafin wax, graphite, or just
> making sure the collet and recieving end are clean. Has anyone tried
> these
> solutions, and do they work?
>
> I'll try cleaning the collet and recieving end next time I use the router.
SFWIW, have had the same problem with a PC690 and 1/4" shank bits.
My solution has been to place collet nut on vice and tap shank out using a
1/4" wood dowel and a hammer.
YMMV
Lew
On Dec 3, 1:41 am, Puckdropper <[email protected]> wrote:
> I have a Ridgid hand-held router that I've been using with 1/2" bits. More
> than once, the collet has stuck and held the bit in place AFTER the nut has
> been loosened and removed.
>
> My research shows a few solutions such as parafin wax, graphite, or just
> making sure the collet and recieving end are clean. Has anyone tried these
> solutions, and do they work?
>
> I'll try cleaning the collet and recieving end next time I use the router.
>
> Puckdropper
> --
> Wise is the man who attempts to answer his question before asking it.
>
> To email me directly, send a message to puckdropper (at) fastmail.fm
You might try: http://www.meyerplastics.com/adhesives_seal_tape/anti-seize_comp_sht.htm
"Lew Hodgett" <[email protected]> wrote in
news:[email protected]:
>
> "Puckdropper" wrote:
>
>>I have a Ridgid hand-held router that I've been using with 1/2" bits.
>>More
>> than once, the collet has stuck and held the bit in place AFTER the
>> nut has
>> been loosened and removed.
>>
>> My research shows a few solutions such as parafin wax, graphite, or
>> just making sure the collet and recieving end are clean. Has anyone
>> tried these
>> solutions, and do they work?
>>
>> I'll try cleaning the collet and recieving end next time I use the
>> router.
>
> SFWIW, have had the same problem with a PC690 and 1/4" shank bits.
>
> My solution has been to place collet nut on vice and tap shank out
> using a 1/4" wood dowel and a hammer.
>
> YMMV
>
> Lew
>
>
My problem is the bit and collet won't come out of the router. I might
even be able to turn the router on with the nut off and use the router!
(Not that I'd try it, however.)
Puckdropper
--
Wise is the man who attempts to answer his question before asking it.
To email me directly, send a message to puckdropper (at) fastmail.fm
I'm not sure how the Ridgid router collet is designed, but other newer name
brand routers have collets with snap rings on the end to keep the nut
attached to the collet and they also serve to pull the collet out of the
router when the nut is unscrewed. Is your snap ring missing? If one belongs
there the end of the collet would have a groove in it for the snap ring.
Charley
"Puckdropper" <[email protected]> wrote in message
news:[email protected]...
> "Lew Hodgett" <[email protected]> wrote in
> news:[email protected]:
>
> >
> > "Puckdropper" wrote:
> >
> >>I have a Ridgid hand-held router that I've been using with 1/2" bits.
> >>More
> >> than once, the collet has stuck and held the bit in place AFTER the
> >> nut has
> >> been loosened and removed.
> >>
> >> My research shows a few solutions such as parafin wax, graphite, or
> >> just making sure the collet and recieving end are clean. Has anyone
> >> tried these
> >> solutions, and do they work?
> >>
> >> I'll try cleaning the collet and recieving end next time I use the
> >> router.
> >
> > SFWIW, have had the same problem with a PC690 and 1/4" shank bits.
> >
> > My solution has been to place collet nut on vice and tap shank out
> > using a 1/4" wood dowel and a hammer.
> >
> > YMMV
> >
> > Lew
> >
> >
>
> My problem is the bit and collet won't come out of the router. I might
> even be able to turn the router on with the nut off and use the router!
> (Not that I'd try it, however.)
>
> Puckdropper
> --
> Wise is the man who attempts to answer his question before asking it.
>
> To email me directly, send a message to puckdropper (at) fastmail.fm
"Charley" <[email protected]> wrote in
news:[email protected]:
> I'm not sure how the Ridgid router collet is designed, but other newer
> name brand routers have collets with snap rings on the end to keep the
> nut attached to the collet and they also serve to pull the collet out
> of the router when the nut is unscrewed. Is your snap ring missing? If
> one belongs there the end of the collet would have a groove in it for
> the snap ring.
>
> Charley
>
The 1/4" collet is set up that way, and it seems to be a good system.
However, the 1/2" is just the standard seperate nut, collet, and router.
My Craftsman (B&D) router/shaper is the same way.
Puckdropper
--
Wise is the man who attempts to answer his question before asking it.
To email me directly, send a message to puckdropper (at) fastmail.fm
"Leon" <[email protected]> wrote in
news:[email protected]:
>
> "Puckdropper" <[email protected]> wrote in message
> news:[email protected]...
>>I have a Ridgid hand-held router that I've been using with 1/2" bits.
>>More
>> than once, the collet has stuck and held the bit in place AFTER the
>> nut has
>> been loosened and removed.
>>
>> My research shows a few solutions such as parafin wax, graphite, or
>> just making sure the collet and recieving end are clean. Has anyone
>> tried these
>> solutions, and do they work?
>>
>> I'll try cleaning the collet and recieving end next time I use the
>> router.
>>
>> Puckdropper
>> --
>> Wise is the man who attempts to answer his question before asking it.
>>
>> To email me directly, send a message to puckdropper (at) fastmail.fm
>
>
> Clean the fittings but I would steer clear of any type of lubricant or
> wax as those will continue to work when you do not want slippage.
>
> I have an old Bosch that does that. I simply gently tap the side of
> the bit shank until it pops loose.
>
Those were my thoughts, too.
Puckdropper
--
Wise is the man who attempts to answer his question before asking it.
To email me directly, send a message to puckdropper (at) fastmail.fm
I remember another router having this problem, although I don't know
which one it was. The problem seemed to be a combination of poor
internal machining of the collet and dirt accumulation.
I think the problem was resolved by cleaning the collet and polishing
the inside fo the collet with a Dremel and a small bit.
Might be worth searching the group archives.
Robert
"Puckdropper" <[email protected]> wrote in message
news:[email protected]...
>I have a Ridgid hand-held router that I've been using with 1/2" bits. More
> than once, the collet has stuck and held the bit in place AFTER the nut
> has
> been loosened and removed.
>
> My research shows a few solutions such as parafin wax, graphite, or just
> making sure the collet and recieving end are clean. Has anyone tried
> these
> solutions, and do they work?
>
> I'll try cleaning the collet and recieving end next time I use the router.
>
> Puckdropper
> --
> Wise is the man who attempts to answer his question before asking it.
>
> To email me directly, send a message to puckdropper (at) fastmail.fm
Clean the fittings but I would steer clear of any type of lubricant or wax
as those will continue to work when you do not want slippage.
I have an old Bosch that does that. I simply gently tap the side of the bit
shank until it pops loose.
Puckdropper wrote:
> My problem is the bit and collet won't come out of the router. I
> might even be able to turn the router on with the nut off and use
> the router! (Not that I'd try it, however.)
Put the nut back on (if it's off) a bit less than finger tight and tap
it with the wrench. Tap...tap...tap...the collet/bit will eventually
loosen. To avoid the problem in the future, take the bit out as soon
as you finish using it.
--
dadiOH
____________________________
dadiOH's dandies v3.06...
...a help file of info about MP3s, recording from
LP/cassette and tips & tricks on this and that.
Get it at http://mysite.verizon.net/xico