I got an 8" grinder. Got an 80x white wheel. Got the spiffy Veritas
rest and holder.
First attempt was with my beater chisel that I use for scraping glue
off the bench and various other nasty business. It actually has a
decent bevel on it for the first time ever now.
Then I went for the pitted #6 blade.
http://www.krtwood.com/burn1.jpg
I was going to show that picture and ask if it was okay if it turned
that color as long as it didn't turn blue, but well once I saw it
zoomed in I could see that it *was* blue in one spot near the top,
which I couldn't see by eye before. So clearly that's bad.
http://www.krtwood.com/burn2.jpg
This blade I still don't care too much about, but it's not garbage.
It's mostly not changed color at all, except for that one spot near
the top again. which this time I don't see any blue. So now I get to
ask my question, is this okay?
The plane iron is thinner than the chisel so I assume it's harder for
it to dissipate the heat. Because it's in the same spot on two
attempts that got hotter it must be a technique thing. I was trying
to just make a light pass straight across, and I went for the water
after every pass. I guess not light enough.
-Leuf
You most likely need to dress the wheel to remove glazed abrasive and
open it up a bit.
In addition you will get less heat if you radius the wheel to make a
smaller contact with the steel.
A 60grit wheel is more than sufficient, after all you will be honing
the cutting edge after grinding.
If you have not flattened the back of the chisel then your best
efforts will be wasted.
Daily Grind Sharpening Service
On Feb 2, 4:43 pm, Leuf <[email protected]> wrote:
> I got an 8" grinder. Got an 80x white wheel. Got the spiffy Veritas
> rest and holder.
>
> First attempt was with my beater chisel that I use for scraping glue
> off the bench and various other nasty business. It actually has a
> decent bevel on it for the first time ever now.
>
> Then I went for the pitted #6 blade.
>
> http://www.krtwood.com/burn1.jpg
>
> I was going to show that picture and ask if it was okay if it turned
> that color as long as it didn't turn blue, but well once I saw it
> zoomed in I could see that it *was* blue in one spot near the top,
> which I couldn't see by eye before. So clearly that's bad.
>
> http://www.krtwood.com/burn2.jpg
>
> This blade I still don't care too much about, but it's not garbage.
> It's mostly not changed color at all, except for that one spot near
> the top again. which this time I don't see any blue. So now I get to
> ask my question, is this okay?
>
> The plane iron is thinner than the chisel so I assume it's harder for
> it to dissipate the heat. Because it's in the same spot on two
> attempts that got hotter it must be a technique thing. I was trying
> to just make a light pass straight across, and I went for the water
> after every pass. I guess not light enough.
>
> -Leuf
"Old guy" <[email protected]> wrote in message
news:NX0xh.1170437$084.358299@attbi_s22...
> And third, if I am sharpening HSS tools (like lathe chisels),I don't dunk
> them in water. The rapid cooling makes for micro cracks which degrade the
> edge quickly.
It is OK to dunk HSS, the key is to not get the metal so screaming hot
before dunking. Think for a moment about the tools for a metal lathe.
For a wood chisel the grinder is a great tool for getting the blade close to
sharp, then you get it sharp by hand with the stone.
--
Roger Shoaf
About the time I had mastered getting the toothpaste back in the tube, then
they come up with this striped stuff.
On Feb 3, 5:25 pm, Leuf <[email protected]> wrote:
> On 2 Feb 2007 14:30:06 -0800, "beecrofter" <[email protected]>
> wrote:
>
>
>
> >You most likely need to dress the wheel to remove glazed abrasive and
> >open it up a bit.
>
> I think that did the trick. How often should the wheel need to be
> dressed?
>
> -Leuf
It varies quite a bit, but you can see the difference in the amount of
material being removed vs hopw hot it gets as well as the wheel
taking on a glazed shine. A dressing brick is just coarse silicon
carbide, much like a rubbing stone for concrete. Don't breathe the
dust! A good jig for chisels is a piece of pvc pipe rested against
your foot ( or a batten on the floor) with the chisel inside. It's
like having a 6' handle on the chisel and puts an ever so slight
radius on the blade in the process. I use a similar setup with timber
framing slicks.
As for squareing things up, nothing beats a line scribed through a
layer of magic marker ink as a guide.
You also may find that a shorter bevel is more durable than the
factory one. An 8" wheel gives a nice hollow grind and saves on
honing time.
Daily Grind
Sounds like you have the right equipment. I love my Veritas rest and
holder.
I've learned some things that you might already know, but I'll pass them on
anyhow.
First, I shape the blade at a 90* bevel. If I'm trying to remove serious
metal, the feather edge will burn every time. After it is shaped/square or
what have you, then I set the bevel angle (and it's so easy with the
Veritas) and sharpen the blunt edge I just made.
The second is to put a finger on the blade about 1" back from the wheel. (I
keep alert, don't want to be known as Stumpy). When my finger gets hot, the
blade is too, and it needs air or water cooling.
And third, if I am sharpening HSS tools (like lathe chisels),I don't dunk
them in water. The rapid cooling makes for micro cracks which degrade the
edge quickly.
It's wonderful to have sharp tools!
Old Guy
"Leuf" <[email protected]> wrote in message
news:[email protected]...
>I got an 8" grinder. Got an 80x white wheel. Got the spiffy Veritas
> rest and holder.
>
> First attempt was with my beater chisel that I use for scraping glue
> off the bench and various other nasty business. It actually has a
> decent bevel on it for the first time ever now.
>
> Then I went for the pitted #6 blade.
>
> http://www.krtwood.com/burn1.jpg
>
> I was going to show that picture and ask if it was okay if it turned
> that color as long as it didn't turn blue, but well once I saw it
> zoomed in I could see that it *was* blue in one spot near the top,
> which I couldn't see by eye before. So clearly that's bad.
>
> http://www.krtwood.com/burn2.jpg
>
> This blade I still don't care too much about, but it's not garbage.
> It's mostly not changed color at all, except for that one spot near
> the top again. which this time I don't see any blue. So now I get to
> ask my question, is this okay?
>
> The plane iron is thinner than the chisel so I assume it's harder for
> it to dissipate the heat. Because it's in the same spot on two
> attempts that got hotter it must be a technique thing. I was trying
> to just make a light pass straight across, and I went for the water
> after every pass. I guess not light enough.
>
>
> -Leuf
I had to learn to use the darn thing. I don't understand why there is so
much slop between the base and the slider part. I prefer to let the bar
ride on the bottom of the slot. Trying to keep it riding on the top of the
slot doesn't work well for me.
What I do is to set the blade up just touching the wheel. Of course after
the first pass it doesn't. So I just put a little downward pressure on the
blade, the tool rest base flexes, and the blade touches the wheel again. I'm
aware it changes the bevel angle a smitch, but I don't worry about it.
It seems to let me grind my tools gently.
As far as square, I've never been able to just put the tool in the slider
piece and have it come out square. I need a visual reference to help me.
I've found that it works best for me to color the back edge of the blade
with a magic marker, then scratch a true square line in the color with an
awl. With that visual reference, I can get the end as true as I want it. I
don't grind all the way back to the mark.
Actually, I use the grinder to get the shape and the bevel on the tool, and
then switch to sandpaper for the sharpening and honing. (Using the cheap
one wheeled $15 honing guide.)
My main use for the tool rest is getting the right bevel on lathe chisels.
It's a pain when EVERYTHING is dull!
Old Guy
"Leuf" <[email protected]> wrote in message
news:[email protected]...
> On Sat, 03 Feb 2007 14:25:49 GMT, "Old guy" <[email protected]> wrote:
>
>>Sounds like you have the right equipment. I love my Veritas rest and
>>holder.
>
> I need more practice. I ended up not even close to square on the
> plane iron. Everything with the rest seems to be square, I even tried
> clamping up one of my squares in the holder and it made even contact
> across the stone, so I'm pretty sure the rest is setup right
>
> There's a lot of play between the slot in the rest and the bar on the
> holder, necessary so you can pivot. Do you keep the bar pushed in, or
> let it rest on the back edge?
>
>
>>It's wonderful to have sharp tools!
>
> I've been putting off a sharpening session for too long. Pretty much
> everything in the shop that's supposed to be sharp aint. There's one
> chisel that's still borderline useableI have the original veritas
> honing guide, I'm probably going to suck it up and get the mk II. I
> have a $50 GC from christmas that has somehow managed to not be spent
> already.
>
>
> -Leuf
On 2 Feb 2007 14:30:06 -0800, "beecrofter" <[email protected]>
wrote:
>
>You most likely need to dress the wheel to remove glazed abrasive and
>open it up a bit.
I think that did the trick. How often should the wheel need to be
dressed?
-Leuf
On Fri, 02 Feb 2007 16:43:13 -0500, Leuf <[email protected]>
wrote:
>I got an 8" grinder. Got an 80x white wheel. Got the spiffy Veritas
>rest and holder.
>
>First attempt was with my beater chisel that I use for scraping glue
>off the bench and various other nasty business. It actually has a
>decent bevel on it for the first time ever now.
>
>Then I went for the pitted #6 blade.
>
>http://www.krtwood.com/burn1.jpg
>
>I was going to show that picture and ask if it was okay if it turned
>that color as long as it didn't turn blue, but well once I saw it
>zoomed in I could see that it *was* blue in one spot near the top,
>which I couldn't see by eye before. So clearly that's bad.
>
>http://www.krtwood.com/burn2.jpg
>
>This blade I still don't care too much about, but it's not garbage.
>It's mostly not changed color at all, except for that one spot near
>the top again. which this time I don't see any blue. So now I get to
>ask my question, is this okay?
Probably.
I wouldn't lose any sleep over it, anyhow- as I use a regular grinder
with stock wheels, I've burned a fairish number of chisels over the
years, and had to grind past the bluing a little bit at a time, and it
has always seemed to me that any loss of temper is confined to the
specific area that changed color. Once the discolored area is ground
away, everything seems to be just fine again.
Also, when I say I've burned chisels in the past, I mean it- what
you've got shown is almost nothing. I wouldn't have even seen it if
you hadn't pointed it out. If it turns dark blue, with some yellow
and orange discoloration around it, that's the time to worry about it.
On Sat, 03 Feb 2007 14:25:49 GMT, "Old guy" <[email protected]> wrote:
>Sounds like you have the right equipment. I love my Veritas rest and
>holder.
I need more practice. I ended up not even close to square on the
plane iron. Everything with the rest seems to be square, I even tried
clamping up one of my squares in the holder and it made even contact
across the stone, so I'm pretty sure the rest is setup right
There's a lot of play between the slot in the rest and the bar on the
holder, necessary so you can pivot. Do you keep the bar pushed in, or
let it rest on the back edge?
>It's wonderful to have sharp tools!
I've been putting off a sharpening session for too long. Pretty much
everything in the shop that's supposed to be sharp aint. There's one
chisel that's still borderline useableI have the original veritas
honing guide, I'm probably going to suck it up and get the mk II. I
have a $50 GC from christmas that has somehow managed to not be spent
already.
-Leuf