Sorry if this questions been around, I can't go back too far...
I remeber that I used to make a utility wood filler from the right color
sawdust and glue.
Now I need some more, and I have the sawust/sanding dust exactly the right
color, but I need to identify a glue that will accept a finish - probably
some type of oil.
Can anyone give me some help?
thanks.
Yeah, you're right. It's the finishing resin. Got turned on to it by a
guitar builder who uses it as a pore filler for the guitar body (sides and
back). After playing around with it, realized it was a perfect filler for
knots and holes because of how thinly it flowed. Works really well for
deeper knots without trapping air pockets inside.
"B A R R Y" <[email protected]> wrote in message
news:[email protected]...
> Gary A in KC wrote:
> >
> > If it's a deep hole, I use Z-Poxy. Much thinner and can be run slowly
into
> > the hole and eliminate air pockets.
>
> Z-Poxy is a brand of epoxy, sold by Zap. I love Zap epoxies and CA.
> There are several formulations of Z-Poxy, not all are that thin.
>
> Are you using the Finishing Resin by chance?
>
> A great way to get any epoxy to flow better is to warm it slightly
> before mixing.
On Sat, 22 Nov 2008 09:51:57 -0600, Steve Turner
<[email protected]> wrote:
>Donna Brandt wrote:
>> Sorry if this questions been around, I can't go back too far...
>>
>> I remeber that I used to make a utility wood filler from the right color
>> sawdust and glue.
>> Now I need some more, and I have the sawust/sanding dust exactly the right
>> color, but I need to identify a glue that will accept a finish - probably
>> some type of oil.
>> Can anyone give me some help?
>>
>> thanks.
>
>Franklin Hide glue.
...clear epoxy works well, also...
cg
Gary A in KC wrote:
> Yeah, you're right. It's the finishing resin. Got turned on to it by a
> guitar builder who uses it as a pore filler for the guitar body (sides and
> back). After playing around with it, realized it was a perfect filler for
> knots and holes because of how thinly it flowed. Works really well for
> deeper knots without trapping air pockets inside.
It's fantastic stuff! I originally used it for fuel proofing model
aircraft engine compartments. It's also really cool when brushed on
fiberglass or carbon fiber cloth.
What lots of folks don't know is that most epoxies can be thinned to a
similar consistency with a dot of denatured alcohol.
"B A R R Y" wrote:
> What lots of folks don't know is that most epoxies can be thinned to
> a similar consistency with a dot of denatured alcohol.
About 5% is the max without adversely affecting physical properties.
The basic blending of the resin is when you establish the viscosity of
epoxy resin by chose of diluents used in the blend.
As you noted in an earlier post, viscosity of epoxy resin is highly
temperature dependant.
Lew
Lew
If you're just using a clear finish, like an oil, lacquer or poly - then use
5 minute epoxy. Once sanded out and finished it well blend in well. I use
this for small knot holes and voids all the time. For a small hole just use
a cyanoacrylate glue. Put the glue in the hole and literally sand over the
surface to drive dust into the glue for filler and color.
If it's a deep hole, I use Z-Poxy. Much thinner and can be run slowly into
the hole and eliminate air pockets.
Gary in KC
"Donna Brandt" <[email protected]> wrote in message
news:[email protected]...
> Sorry if this questions been around, I can't go back too far...
>
> I remeber that I used to make a utility wood filler from the right color
> sawdust and glue.
> Now I need some more, and I have the sawust/sanding dust exactly the right
> color, but I need to identify a glue that will accept a finish - probably
> some type of oil.
> Can anyone give me some help?
>
> thanks.
>
>
Donna Brandt wrote:
> Sorry if this questions been around, I can't go back too far...
>
> I remeber that I used to make a utility wood filler from the right
> color sawdust and glue.
> Now I need some more, and I have the sawust/sanding dust exactly the
> right color, but I need to identify a glue that will accept a finish
> - probably some type of oil.
> Can anyone give me some help?
>
> thanks.
Use whatever finish you plan to use as a binder.
--
dadiOH
____________________________
dadiOH's dandies v3.06...
...a help file of info about MP3s, recording from
LP/cassette and tips & tricks on this and that.
Get it at http://mysite.verizon.net/xico
Gary A in KC wrote:
>
> If it's a deep hole, I use Z-Poxy. Much thinner and can be run slowly into
> the hole and eliminate air pockets.
Z-Poxy is a brand of epoxy, sold by Zap. I love Zap epoxies and CA.
There are several formulations of Z-Poxy, not all are that thin.
Are you using the Finishing Resin by chance?
A great way to get any epoxy to flow better is to warm it slightly
before mixing.
Donna Brandt wrote:
> Sorry if this questions been around, I can't go back too far...
>
> I remeber that I used to make a utility wood filler from the right color
> sawdust and glue.
> Now I need some more, and I have the sawust/sanding dust exactly the right
> color, but I need to identify a glue that will accept a finish - probably
> some type of oil.
> Can anyone give me some help?
>
> thanks.
Franklin Hide glue.
--
Free bad advice available here.
To reply, eat the taco.
http://www.flickr.com/photos/bbqboyee/